ORiNG TGXPS-1080-M12-MV Series User manual

Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
ORing's Transporter series un-managed Ethernet switches are designed for
TM
industrial applications, such as rolling stock, vehicle, and railway applications.
The is an un-managed PoE Ethernet switch withTGXPS-1080-M12-MV
8x10/100/500/1000Base-T(X) P.S.E. which is specifically designed for the
toughest and fully compliant with EN50155 requirement. TGXPS-1080-M12-
MV also supports Power over Ethernet, a system to transmit electrical power,
along with data, to remote devices over standard twisted-pair cable in an
E t h e r n e t n e t w o r k . E a c h s w i t c h h a sT G X P S - 1 0 8 0 - M 1 2 - M V
8X10/100/500/1000Base-T(X) IEEE 802.3af/at P.S.E. (Power Sourcing
Equipment) ports, but the PoE total power budget is 60Watts Max. P.S.E. is a
device (switch or hub for instance) that will provide power in a PoE setup.
TGXPS-1080-M12-MV EN50155 Ethernet switch use M12 connectors to
ensure tight, robust connections, and guarantee reliable operation against
environmental disturbances, such as vibration and shock. In addition, the wide
operating temperature range from -40 C to 75 C can satisfy most of operating
o o
environment. Therefore, the switch is one of the most reliable choices for
rolling stock and highly-managed PoE Ethernet application.
While installing in the train, is mainly used for in-trainTGXPS-1080-M12-MV
monitoring and Entertainment service due to its high-speed Gigabit Ethernet
connection and PoE capability. Devices connected will be IP camera or CCTV
for the use of train surveillance. As an unmanaged Ethernet Switch, TGXPS-
1080-M12-MV is not able and will not be used for any control related
application. Its main function is simply forwarding the Ethernet packet from one
Ethernet based device to another Ethernet device which are all connected to
the Switch.
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1: Hold the evice upright against the walld
Step 2: Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Step 3: Slide the evice downwards and tighten the four screws for added stability.d
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available.
Elevated Operating Ambient: If installed in a closed environment, make
sure the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe
operation of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Consideration should be given to the connection of theCircuit Overloading:
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when
Safety & Warnings
For pin assignments of power and relay output ports, please refer to the following tables.
Contents
TGXPS-1080-M12-MV or
TGXPS-1080-M12-BP2-MV
Pictures Number
1
Dimension
Panel Layouts
Front View
1. Power status LED
2. Power input port
3. Relay output port
4. LNK/ACT & Speed LED for Gigabit ports
(1Gbps/10Mbps/100Mbps)
5. LNK/ACT & Speed LED for Gigabit ports (500Mbps)
6. Gigabit Ethernet ports
(G5-G8 of TGXPS-1080-M12-BP2-MV are bypass ports)
7. PoE status LED
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports one set of power supplies and uses the 7/8 inch
M23 5-pin male connector on the front panel for the power input.
Step 1: Insert a power cable to the power connector on the device.
Step 2: Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Relay output port pinouts
Relay N.C.
3A@24VDC
Network Connection
The device provides Ethernet ports in M12 connector type. According to the link type, the switch
uses CAT 3, 4, 5,5e UTP cables to connect to any other network devices (PCs, servers, switches,
routers, or hubs). Please refer to the following table for cable specifications.
TGXPS-1080-M12-MV Series
TGXPS-1080-M12-MV Series 1907-200-T1080MVXX1-FX010
S w i tc h
E N 5 0 1 5 5
EN50155 8-port unmanaged
Gigabit PoE Ethernet switch
I N D U S T R I A L
1
2
3
4
5
66 7
Instead of screwing the screws in all the way, it is advised
to leave a space of about 2mm to allow room for sliding
the switch between the wall and the screws.
The switch uses the M12 A-coded 5-pin female connector
on the front panel for relay output. Use a power cord with an
M12 A-coded 5-pin male connector to connect the relay.
The relay contacts will detect power off event to trigger
warning system.
For pin assignments of the LAN ports, please refer to the following tables.
QIG 1
Cable
Type
Max. Length
Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) M12 A-coding connector
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) M12 A-coding connector
1000BASE-T Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328ft) M12 A-coding connector
4
5
6
7
8
21
3
10/100/1000Base-T(X) M12 port
PIN Definition
1BI_DC+
2BI_DD+
3BI_DD-
4BI_DA- / PoE Vout+
5BI_DB+ / PoE Vout-
6BI_DA+ / PoE Vout+
7BI_DC-
8BI_DB- / PoE Vout-
Unit =mm (Tolerance ±0.5mm)
150.0
196.0
160.0
65.0
6.50
170.4
81.5
111.0
Ø5.0
Ø8.00
Rel ay Outp ut
Ø4.0
175.9
Pow er
Power
Relay N.C.
3A@24 VDC
N.C.
N.C.
V+
V-
TGXP S-1080-M 12-BP2- MV
Power
Failu re
Bypas s
Power
Failu re
Bypas s
72~ 110VDC
PoE
LNK/A CT
10/100/1G
500M
G1 G5
G2 G6
G3 G7
G4 G8
4
5
6
7
8
21
1 BI_DC +
2 BI_DD +
3 BI_DD -
4 BI_DA - / PoE Vo ut+
5 BI_DB + / PoE Vout -
6 BI_DA + / PoE Vout +
7 BI_DC -
8 BI_DB - / PoE Vout -
G1~ G 8
PoE
LNK/A CT
10/100/1G
500M
PoE
LNK/A CT
10/100/1G
500M
PoE
LNK/A CT
10/100/1G
500M
Rel ay Outp ut
Pow er
Powe r
Rela y N.C.
3A@2 4VDC
N.C.
N.C.
V+
V-
TGX PS-108 0-M12- BP2-MV
Powe r
Fail ure
Bypa ss
Powe r
Fail ure
Bypa ss
72~ 110VD C
PoE
LNK/ ACT
10/100/1G
500M
G1 G5
G2 G6
G3 G7
G4 G8
4
5
6
7
8
21
1 BI_D C+
2 BI_D D+
3 BI_D D-
4 BI_D A- / PoE Vout +
5 BI_D B+ / PoE Vou t-
6 BI_D A+ / PoE Vou t+
7 BI_D C-
8 BI_D B- / PoE Vou t-
G1~ G 8
PoE
LNK/ ACT
10/100/1G
500M
PoE
LNK/ ACT
10/100/1G
500M
PoE
LNK/ ACT
10/100/1G
500M
N.C .
N.C .
V+
V-

Q I G Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
Version 1.0
Q I G
S w i tc h
E N 5 0 1 5 5
I N D U S T R I A L
EN50155 8-port unmanaged
Gigabit PoE Ethernet switch
Configurations
After installing the switch and connecting cables, start the evice byd
turning on power. The green power LED should turn on. Please refer to the
following tablet for LED indication.
LED
Color
Status
Description
PWR Green On Power is enabled
10/100/500/1000Base-T(X) Ethernet ports
10/100/1G
Green On Port is running at 1Gbps
Amber On Port is running at 10/100 Mbps
500M Amber On Port is running at 500Mbps
PoE Blue On PoE power is enabled
Regulatory Approvals
EN 55032, CISPR32 , EN 61000-3-2, EN 6100 0-3-3, FCC Part 15B class A
EMI
EN 55024 (IEC/EN 61 000-4-2 (ESD), IE C/ EN 61000-4-3 (RS) ,IEC/EN 61000-4 -4 (EFT),
IEC/EN 61000-4- 5 (Surge), IEC/EN 6 10 00-4-6 (CS), IE C/ EN 61000-4-8(PF MF), IEC/EN 61000 -4 -11 (DIP))
EMS
IEC60068-2-27
Shock
IEC60068-2-31
IEC60068-2-6
Vibration
Free Fal l
MTBF
229942.9636 hrs
Specifications
Power
Input power
Power Consump tion(Typ.) 72VDC@9Wa tts Max. (power con sumption of P.S.E. is not inc lu ded)
110VDC@12Watts Max. (power co ns umption of P.S.E . is not included)
Physical Characteristic
Enclosure IP-30
Dimension (W x D x H) 150(W) x 65(D) x 196( H) m m (5.90 x 2.56 x 7.66 inc h. )
Weight ( g) 1320 g
Environmental
-40 to 85 C (-40 to 185 F)
o o
Storage Temperature
5% to 95% Non-conde nsing
Operating Hum idity
Fault Contact
Rela y Relay ou tput to carry capac it y of 3 A at 24VDC on M12 femal e co nnector (5-pi n M1 2 A-co di ng )
Overload Cu rrent Protection
Reve rse Po larity Protection
Present
Present
-40 to 75 C (-40 to 167 F)
o o
Operating Temperatur e
ORing Switch Model
10/100/500/1000B ase-T(X)
Port s in M12 With P.S.E .
8 x M12 female connector
(8 pin A-coding)
Physical Ports
Technology
Ethernet Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Bas e-TX
IEEE 802.3ab for 1000B ase-T
IEEE 802.3x for Flow con trol
IEEE 802.3af complia nt PoE specific ation (Ma ximum 15.4Watts per p ort)
IEEE 802.3at complia nt PoE specific ation (Ma ximum 30Watts per por t)
4K MAC addresses
MAC Table
Store-and -Forward
Processing
8 x M12 female connector
(8-pin A-coding, bypass function
included on p ort5~8)
1350 g
TGXPS-1080-M12-MV TGXPS-1080-M12-BP2-MV
72/96/110VDC (5 0.4-154VDC). 7/ 8 in ch 5-pin male conne ct or
PoE Output Total Power
Budget 60 Watts
Warranty
5 ye ars
172181.8534 hrs
ORing Industrial Networking Corp.
Copyright© 2019 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oringnet.com
E-mail: [e-mail]
LED indicators
Green : Power LED x 1
Power Indicat or
Top for 10/100/100 0Mbps por t Link/Act in dicator.
Green for 1Gbps link, Amber for 10/ 100 Mbps link
Middle Amber for 500Mb ps port Link/Act indic ator
Bottom blue for PoE Injected indicato r
10/100/500/1000B ase-T(X)
M12 port indicator and PoE
indicator
CE EMC (EN 55024, EN 55 032), FCC Part 15B, EN 50155(EN 5 01 21-1, EN 50121-3- 2)
EMC
EN 60950-1
EN 50155 (IEC 61373 )
Other
Safety
TGXPS-1080-M12-MV Series
TGXPS-1080-M12-MV Series