ORiNG TGAR-1062PLUS-3GS-M12 User manual

Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
QIG 1907-2-29-TGAR+GPS-1.0
Designed for industrial and rolling stock wireless applications with two LAN
ports in M12 connectors and EN50155 compliance, the
are IEEE802.11 a/b/g/n routers capable of
providing a fast and effective way to communicate with the Internet over
wired or wireless LANs. The series includes PoE models and 3G/4G models
with GPS functions. The series of devices can be configured to operate in 3
modes of routing function: dynamic/static IP route, PPPoE authentication,
and cellular modem dial up. You can set up WLAN environment to fulfill
demands of various applications rapidly by dialing up cellular modem. With
dual Ethernet ports in switch mode, you can use Daisy Chain to reduce the
usage of Ethernet switch ports. The router also provides VPN capabilities
which create encrypted virtual tunnels on the Internet, allowing remote or
mobile users to connect to the network of your office.
TGAR-
1062/2062/1662+ series
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below
to install the device on the wall.
Hold the evice upright against the wall
Insert four screws through the large opening of
the keyhole-shaped apertures at the top and bottom of
the unit and fasten the screw to the wall with a screwdriver.
Slide the evice downwards and tighten the four
screws for added stability.
Step 1:
Step 2:
Step 3:
d
d
The devices are shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
CD
3G or 4G Antenna
Router
Pictures Number
1
1
QIG 1
2.4GHz/5GHz Wi-Fi
Antenna
2 (TGAR-1062+/2062+) or
4 (TGAR-1662+)
Dimension
Panel Layouts
Front Panel
Power
DO DI ETH2
(P.O.E)
ETH1
Console
RelayOutput
1BI_DC+
2BI_DD+
3BI_DD-
4BI_DA-
5BI_DB+
6BI_DA+
7BI_DC-
8BI_DB-
4
5
6
7
8
21
3
V1+
V1-
V2+
V2-
RSVD
RxD
RS-232,115200bps,8, N, 1
GND
TxD
N.C.
Relay N.C.
1A@24VDC
DI1
COM
DI2
DI3DI4
GND
DO1 DO2
DO3DO4
TGAR-1062+-GPS-M12
PWR1
PWR2
(P.O.E)
ETH1
ETH2
Fault
WLAN
1
3
25
6
7
8
9
10
TGAR-1062+-3/4GS-M12
11
TGAR-1662+-3/4GS-M12
1. PWR status LED
(PW2 with PoE indicator)
2. LAN port status LED
3. Fault status LED
4. WAN status LED
Wireless
EN50155
ACCESS POINT ROUTER
EN50155 Industrial Wireless LAN
PoE Access Point Router
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for the dual power inputs.
Insert a power cable to the power connector on the device.
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Step 1:
Step 2:
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay N.C.
1A@24VDC
DI/DO Port Pinouts
DODI
DI1
COM
DI2
DI3DI4
GND
DO1 DO2
DO3DO4
Network Connection
The AP router has two 10/100/1000 Base-T(X) Ethernet ports. According to the link type, theAP
router uses CAT 3, 4, 5, 5e, UTP cables to connect to any other network device (PCs, servers,
evicees, routers, or hubs). Please refer to the following table for cable specifications.d
Cable Type Max. Length Connector
10Base-T Cat. 3, 4, 5 10 0-ohm UTP 100 m ( 328 f t) M12
100Base-TX Cat. 5 100-ohm UTP UTP 100 m ( 328 f t) M12
1000Base-T Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m ( 328 f t) M12
1 (TGAR-1062+/1662+) or
2 (TGAR-2062+)
SIMCard Slot
Cellular
ANT.
Power
DO DI ETH2
(P.O.E)
ETH1
Console
RelayOutput
1BI_DC+
2BI_DD+
3BI_DD-
4BI_DA-
5BI_DB+
6BI_DA+
7BI_DC-
8BI_DB-
4
5
6
7
8
21
3
V1+
V1-
V2+
V2-
RSVD
RxD
RS-232,115200bps,8, N, 1
GND
TxD
N.C.
Relay N.C.
1A@24VDC
DI1
COM
DI2
DI3DI4
GND
DO1 DO2
DO3DO4
TGAR+GPS Series
PWR1
PWR2
(P.O.E)
ETH1
ETH2
Fault
WAN
WLAN1
WLAN2
R2.5
168.4
7.50
R4.0
86.0
56.5
3.50
WIFI1
ANT.1
WIFI2
ANT.1
Reset
196.1
125.6
15.0
6519.1
12.5
WAN
TGAR-2062+-3/4GS-M12
5. WLAN status LED
6.Relayoutputport
7. Console port
8. Ethernet LAN ports
(ETH2withPoE)
4
1312
Power
DO DI ETH2
(P.O.E)
ETH1
Console
RelayOutput
1BI_DC+
2BI_DD+
3BI_DD-
4BI_DA-
5BI_DB+
6BI_DA+
7BI_DC-
8BI_DB-
4
5
6
7
8
21
3
V1+
V1-
V2+
V2-
RSVD
RxD
RS-232,115200bps,8, N, 1
GND
TxD
N.C.
Relay N.C.
1A@24VDC
DI1
COM
DI2
DI3DI4
GND
DO1 DO2
DO3DO4
TGAR-2062+-GPS-M12
PWR1
PWR2
(P.O.E)
ETH1
ETH2
Fault
WLAN
1
3
25
6
7
8
9
10
11
WAN1 4
1312
WAN2
Power
DO DI ETH2
(P.O.E)
ETH1
Console
RelayOutput
1BI_DC+
2BI_DD+
3BI_DD-
4BI_DA-
5BI_DB+
6BI_DA+
7BI_DC-
8BI_DB-
4
5
6
7
8
21
3
V1+
V1-
V2+
V2-
RSVD
RxD
RS-232,115200bps,8, N, 1
GND
TxD
N.C.
Relay N.C.
1A@24VDC
DI1
COM
DI2
DI3DI4
GND
DO1 DO2
DO3DO4
TGAR-1662+-GPS-M12
PWR1
PWR2
(P.O.E)
ETH1
ETH2
Fault
WLAN1
1
3
2
5
6
7
8
9
10
11
WAN 4
1312
WLAN2
WIFI
ANT.1
Reset
1
2
1. 3G/4G Antenna connector
2. Reset button
3. GPS antenna connector
Side Panel
Allen Key 1
PoE
Circuit Overloading: Consideration should be given to the connection of the equipment to
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
9. DI/DO ports
10. Power connector
11. 2.4/5GHz Wi-Fi antenna
12. Cellular antenna connector
13. SIM card slot
14. Ground
WIFI ANT.1
GPS ANT
1 3
Bottom Panel
TGAR-2062+-3/4GS-M12
SIMCardSlot2
Cellular2
ANT.
Top Panel
SIMCard Slot
Cellular
ANT.
SIMCardSlot
Cellular
ANT.
TGAR-1062+/1662+
-3/4GS-M12
TGAR-2062+-3/4GS-M12
TGAR+ GPS Series
TGAR+ GPS Series
14 1413 12 14

QIG Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
Version 1.0
QIG
Configurations
After installing the router and connecting cables, start the evice by
turning on power. The green power LED should turn on. Please refer to
the following tablet for LED indication.
d
1. Launch the Internet Explorer and type in IP address of the device. The default static
IP address is 192.168.10.1
Specifications
Follow the steps below to log in and access the system:
2. Log in with default user name and password (both are ).admin
3. After logging in, you should see the following screen. For more information on
configurations, please refer to the user manual. For information on operating the device
using ORing’s Open-Vision management utility, please go to ORing website.
Power
Redundant Input Power Dual Power Inputs. 12~48 VDC on M23 connector (24 VDC Typ.)
Physical Characteristic
Enclosure IP-40
Dimension(WxDxH) 125(W) x 65(D) x 196(H) mm (4.92 x 2.56 x 7.72 inch.)
Weig ht ( g)
Environmental
-40to85 C(-40to185 F)
oo
Storage Temperature
5% to 95% Non-condensing
Operating Humidity
Regulatory Approvals
FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN55011, EN50121-4)
EMI
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27, EN61373
Shock
IEC60068-2-32
IEC60068-2-6
Vibration
Free Fall
Warranty
5 years
Frequency Band
Transmission Rate
Encryption Security
WEP: (64-bit, 128-bit key supported)
WPA/WPA2: (WEP and AES encryption)
WPA-PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
802.11i
Wireless Security SSID broadcast disable
Transmit Power
Receiver Senstivity
Protocol Support
Protocol ARP,BOOTP,DHCP,DNS,HTTP,IP,ICMP,SNTP,TCP,UDP,RADIUS,SNMP,PPPoE,STP(IEEE802.1D)
EN60950-1
Safety
-25to70 C(-13to158 F)
oo
Operating Temperature
ORing WLAN Access
Point Model
10/100/1000Base-T(X) Ports in
M12 Auto MDI/MDIX
(8-pin A-coding)
2 (PoE P.D. present at ETH2 Fully compliant with IEEE 802.3af)
Physical Ports
Technology
Modulation
WLAN Interface
Antenna and Connector 4 x External reverse SMA type
antenna connector
Radio Frequency Type DSSS, OFDM
TGAR-1062+
-3GS-M12
IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g: OFDM with BPSK, QPSK, 16QAM, 64QAM
IEEE802.11a: OFDM with BPSK, QPSK, 16QAM, 64QAM
IEEE802.11n: BPSK, QPSK, 16-QAM, 64-QAM
America / FCC : 2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz(9channels)
EuropeCE/ETSI:2.412~2.472Ghz(13channels)
5.180~5.240 Ghz (4 channels)
802.11a: -68dBm±2.0dB @ 54 Mbps
802.11b: -82dBm dB @ 11Mbps
802.11g: -68dBm dB @ 54Mbps
802.11gn HT20: -64dBm
±2.0
±2.0
±2.0dB @150Mbps
802.11gn HT40: -60dBm±2.0dB @300Mbps
802.11an HT20: -64dBm±2.0dB @150Mbps
802.11an HT40: -60dBm±2.0dB @300Mbps
985 g
IEEE801.11b: 1/ 2/ 5.5/ 11 Mbps
IEEE801.11a/g: 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
IEEE802.11n: up to 300Mbps
802.11a: 12dBm dBm
802.11b: 18dBm dBm
802.11g: 15dBm dBm
802.11gn HT20: 13dBm m@150Mbps
802.11gn HT40: 12dBm m@300Mbps
802.11an HT20: 12dBm m@150Mbps
802.11an HT40: 12dBm dBm@300Mbps
±1.5
±1.5
±1.5
±1.5 dB
±1.5 dB
±1.5 dB
±1.5
DI/DOportinM12
(5-pin A-coding)
RS-232ConsoleportinM12
(5-pin A-coding)
RelayportinM12
(5-pin A-coding)
2(DIx4andDOx4)
115200, 8 ,N ,1
1A@24VDC
2 x External reverse SMA type antenna connector
Resetting
To restore the device configurations back to the factory defaults, press the button for a
few seconds. Once the power indicator starts to flash, release the button. The device will
then reboot and return to factory defaults.
Reset
TGAR-1062+
-4GS-M12
TGAR-2062+
-3GS-M12
TGAR-2062+
-4GS-M12
TGAR-1662+
-3GS-M12
TGAR-1662+
-4GS-M12
SIMCardSlot 121
Cellular Interface
Cellular Standard
GSM/GPRS/
EGPRS/ EDGE /
WCDMA/HSDPA
/HSUPA
GSM/GPRS/
EGPRS/EDGE/
WCDMA/HSDPA
/ HSUPA /HSPA+
/LTE
GSM/GPRS/
EGPRS/EDGE/
WCDMA/HSDPA
/HSUPA
GSM/GPRS/
EGPRS/EDGE/
WCDMA / HSDPA
/ HSUPA /HSPA+
/LTE
GSM/GPRS/
EGPRS/ EDGE /
WCDMA / HSDPA
/HSUPA
GSM / GPRS/
EGPRS/EDGE/
WCDMA/HSDPA
/ HSUPA /HSPA+
/LTE
Antenna Connector 1 x Reverse
SMA Female
Dual-band:
HSUPA 1900/
2100 MHZ
Quad-band:
GSM/ GPRS/
EDGE 850/900/
1800/1900 Hz
WCDMA/HSDPA
850/900/1900/
2100 MHz
Band Option
America(US)
Europe(EU)
LTE: 700/1700/
2100 MHZ
UMTS/HSDPA/
HSUPA/HSPA+/
DC-HSPA+: 800
/850/1900/2100
MHZ
GSM/GPRS/
EDGE: 850/900/
1800/1900 MHz
LTE: 800/900/
1900/2100/2600
MHZ
UMTS/HSDPA/
HSUPA/HSPA+/
DC-HSPA+: 900
/2100 MHZ
GSM/GPRS/
EDGE: 900/1800
/1900 MHZ
Dual-band:
HSUPA 1900/
2100 MHZ
Quad-band:
GSM/ GPRS/
EDGE 850/900/
1800/1900 Hz
WCDMA/HSDPA
850/900/1900/
2100 MHz
America(US)
Europe(EU)
LTE: 700/1700/
2100 MHZ
UMTS/HSDPA/
HSUPA/HSPA+/
DC-HSPA+: 800
/850/1900/2100
MHZ
GSM/GPRS/
EDGE: 850/900/
1800/1900 MHz
LTE: 800/900/
1900/2100/
2600 MHZ
UMTS/HSDPA/
HSUPA/HSPA+/
DC-HSPA+: 900
/2100 MHZ
GSM/GPRS/
EDGE: 900/1800
/1900 MHZ
Dual-band:
HSUPA 1900/
2100 MHZ
Quad-band:
GSM/ GPRS/
EDGE 850/900/
1800/1900 Hz
WCDMA/HSDPA
850/900/1900/
2100 MHz
America(US)
Europe(EU)
LTE: 700/1700/
2100 MHZ
UMTS/HSDPA/
HSUPA/HSPA+/
DC-HSPA+: 800
/850/1900/2100
MHZ
GSM/GPRS/
EDGE: 850/900/
1800/1900 MHz
LTE: 800/900/
1900/2100/
2600 MHZ
UMTS/HSDPA/
HSUPA/HSPA+/
DC-HSPA+: 900
/2100 MHZ
GSM/GPRS/
EDGE: 900/1800
/1900 MHZ
Fault Contact
Relay Relay output to carry capacity of 1A at 24VDC
Power Consumption(Typ.) 9 Watts 15 Watts9.5 Watts 13 Watts 14 Watts13 Watts
Overload Current Protection Present
Reverse Polarity Protection Present
968 g 1030 g 1033 g 1114 g1098 g
1 x Reverse
SMA Female
2 x Reverse
SMA Female
M12/8P Pin Definition
PIN Definition
1BI_DC+
2BI_DD+
3BI_DD-
4BI_DA-
5BI_DB+
6BI_DA+
7BI_DC-
8BI_DB-
Console Port Pin Definition
4
5
6
7
8
21
3
RSVD
RxD
RS-232, 115200bps, 8, N, 1
GND
TxD
N.C.
LED Color Status Descri pti on
PWR1 Green On DC power 1 activated.
PWR2 (Po E) Green On DC power 2 activated or PoE enabled (when
devi ce is not connect ed to power suppl y)
On Port is linked
ETH1 Green
Blinking Data transmitted.
On Port is linked
ETH2 Green
Blinking Data transmitted.
On WLAN is activated
WLAN 1 (2) Green
Blinking Transmitting data
WAN 1 ( 2 ) Green On Mode m is connected
Faul t Red On Error occurs (power fails or port disconnected)
Wireless
EN50155
ACCESS POINT ROUTER
EN50155 Industrial Wireless LAN
PoE Access Point Router
TGAR+ GPS Series
TGAR+ GPS Series
PoE
GPS
Antenna and Connector
Frequency 1575.42MHz
1 x External SMA antenna
connector
1 x External SMA antenna
connector
1 x External SMA antenna
connector
ORing Industrial Networking Corp.
Copyright© 2014 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]
1 x SMA Female 2 x SMA Female 1 x SMA Female