Osram BY-M46 User manual

BY-M46 V3.0 version
12*4in1 40w wash zoom moving head
User manual
P le a se rea d t he ins t r u ction s ca refu ll y before use

2
TABLE OF CONTENTS
1. S af ety I nst r uctions ..................................................................................................2-4
2. Technical Specifications ....................................................................................... 4-5
3. Lux Date ..................................................................................................................... 5
4. How To Control The Unit ................................................................................. 6-12
5. shape ........................................................................................................................ 13
6. Trouble shooting ......................................................................................................14
7. Fixture Cleaning ...................................................................................................... 15
statement
The product has well capability and intact packing when leave
factory. All of the user should comply with warning item and manual, any
misuse cause of the damages are not included in our guarantee, and
also can not be responsible for any malfunction & problem owing to
ignore the manual.
1. S af ety I nst r uctions
Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using
the unit.

Before operating, ensure that the voltage and frequency of power
supply match the power requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order
to avoid electric shock.

3

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at
least 50cm from adjacent surfaces. Be sure that no ventilation slots are
blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as
it is fire hazard.

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head
only, but always by taking its base.
 Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the
temperature is higher than this Unit surface temperature may reach up to 85℃.
DO NOT touch the housing bare-hand during its operation. Turn off the power
and allow about 15 minutes for the unit to cool down before replacing or serving.

In the event of serious operating problem, stop using the unit
immediately.Never try to repair the unit by yourself. Repairs carried out by
unskilled people can lead to damage or malfunction. Please contact the
nearest authorized technical assistance center. Always use the same type
spare parts.

DO NOT touch any wire during operation as high voltage might be causing
electric shock.
Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to
rain or moisture.

DO NOT open the unit within five minutes after switching off.

The housing, the lenses, or the ultraviolet filter must be replaced
if they are visibly damaged.
Caution:

4
There are no user serviceable parts inside the unit. DO NOT open the housing
or attempt any repairs yourself. In the unlikely event your unit may require
service, please contact your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that
the unit is firmly fixed to avoid vibration and slipping while operating.
And make sure that the structure to which you are attaching the unit is secure
and is able to support a weight of 10 times of the unit’s weight. Also always use a
safety cable that can hold 12 times of the weight of the unit when installing the
fixture.
The equipment must be fixed by professionals. And it must be fixed at a place
where is out of the touch of people.
2. Technical Specifications
Light Sources: 12 x 40W 4in1 RGBW LED
Beam Angle: 6°~ 45°
Power Consumption: 500W
Power Voltage: AC 100-240V, 50/60Hz
Dimension: 32*25.6* 40.1 cm
Net Weight: 12.5 Kgs
Packing size: 50.5x32.5x39cm
Control
DMX Channel: 19/31 Channel
Control Modes: DMX512/mater-Slave/Auto Run/Music
Pan/Tilt
Pan/Tilt: 540°or 360°in optional / 270°
Pan/Tilt Resolution: 8/16 bit
One full route of pan finished time is 2.4 seconds
Construction
Display: 180°reversible LCD colorful Display

5
Data In/Out socket: 3-pin & 5-pin XLR sockets
Power Socket: PowerCon in/out
Protection Rating: IP20
Features
Motorized liner zoom system, zoom range: 6°~45°
Outstanding color macro effect
Dimmer: 0~100% smooth dimming
Variable strobe effects
Fast, quiet operation and flicker free
4 zones different control
3. Lux Date

6
4. How To Control The Unit
Th e D M X512 is w id ely used in intellig ent ligh ti ng co n tr ol,with a DMX 512
controller.connect several lights together,dmx in and dmx out,
3 p in XLR co nn ectors : Pin 1: G ND , Pin 2: Nega tive s ig n a l (-), Pin 3: P o s itive s i gna l
(+)
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
uP To go forward in the selected functions
ENTER To confirm the selected functions
Set DM X Address Code
1 Press "Menu" to "Set DMX Address",and press"ENTER" keys to enter into
2 Show "Set DMX Address DMX Address:001",Press the "UP and DOWN"
keys to amended
3 Press "ENTER"keys to save and Exit,Press the"MENU"Keys does not save and

7
Exit
1.Address
Set address code 001--512
2.Run Mode
1.DMX512
2.AUTO
3.SOUND
3.Reverse
1.Pan
1.Yes
reverse
2.Tilt
2.No
forward
3.Display
4.Channel
1.31Channels
2.19Channels
5.Pan Degree
1.540
2.360
6.Mic Sense
001--100
sound control adjust
sensitiveness
7.Inform
7.Inform
1.CH Value
display all channel values
2.Temp
display led board temperature

8
3.Soft v3.0
software version number
8.Reset
1..Yes
2.No
9.Default
1.yes
2.No
10.Adjust
Pass Word
UP+DOWN+UP+DOWN
RGBW
0-255 Change the value to
adjust brightness temperature
1.Pan
Pan fine-adjust
2.Tilt
Tilt fine-adjust
3.Focus
Zoom fine-adjust
4.Red
Change the value,adjust the
white balance
5.Green
6.Blue
7.White

9
DMX channel´s functions and values (19/31DMX channels):
19 channels
channel
value
Description
1
0--255
Pan
2
0--255
Pan fine-adjust
3
0--255
Tilt
4
0--255
Tilt fine-adjust
5
0--255
Pan tilt speed
6
0--15
No function
16--214
strobe from slow to fast
215--255
random strobe
7
0--255
Dimming
8
0--49
Mode 1
50--99
Mode 2
100--149
Mode 3
150--255
Mode 4
9
0--255
zoom
10
0--255
R
11
0--255
G
12
0--255
B
13
0--255
W
14
0--16
No function
17--255
Rainbow
15
0--49
No function

10
50--255
color auto run from fast to slow
16
16
0--19
No function
20--39
Zone 1
40--59
Zone 2
60--79
Zone 3
80--99
Zone 4
100--119
Zone 1+2+3
120--139
Zone 1,2,3 rotate counterclockwise
140--159
Zone 1,2,3 rotate clockwise
160--179
change between zone 4 and zone 1+2+3
180-255
keep zone 4,zone 1,2,3 counterclockwise
17
0--255
flexible figure speed from fast to slow
18
0--255
flexible figure gradual change from fast to
slow
19
0-79
No function
80--99
Reset
100--255
No function
31 channels
channel
value
Description
1
0--255
Pan
2
0--255
Pan fine-adjust
3
0--255
Tilt
4
0--255
Tily fine-adjust
5
0--255
Pan tilt speed

11
6
0--15
No function
16--214
strobe from slow to fast
215--255
random strobe
7
0--255
Dimming
8
8
0--49
Mode 1
50--99
Mode 2
100--149
Mode 3
150--255
Mode 4
9
0--255
zoom
10
0--255
R
11
0--255
G
12
0--255
B
13
0--255
W
14
0--255
R
15
0--255
G
16
0--255
B
17
0--255
W
18
0--255
R
19
0--255
G
20
0--255
B
21
0--255
W
22
0--255
R
23
0--255
G
24
0--255
B
25
0--255
W

12
26
0--16
No function
17--255
Rainbow
27
0--49
No function
50--255
color auto run from fast to slow
28
28
0--19
No function
20--39
Zone 1
40--59
Zone 2
60--79
Zone 3
80--99
Zone 4
100--119
Zone 1+2+3
120--139
Zone 1,2,3 rotate counterclockwise
140--159
Zone 1,2,3 rotate clockwise
160--179
change between zone 4 and zone 1+2+3
180-255
keep zone 4,zone 1,2,3 counterclockwise
29
0--255
flexible figure speed from fast to slow
30
0--255
flexible figure gradual change from fast to
slow
31
0-79
No function
80--99
Reset
100--255
No function

13
5.Shape

14
6. Trouble shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e
s o m e s ug g es tion s fo r ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Ch eck th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a g e on th e m a i n co nn e ct o r .
3. Ch eck th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link
p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess
s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Ch eck if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta g e c a b les th a t
m a y c a us e d a m a g e or in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is
b r oken.
2. The motor’s drive IC on the PCB might be out of condition.

15
7. Fixture Cleaning
Th e clean ing o f inter na l a nd ex ter na l optica l lens es a nd/or m ir r ors m u s t b e c a rr ied
ou t p eriodica lly to optim iz e ligh t ou tput . Cle a nin g f r eq uency d e p end s on t h e
environm ent in w hich t h e f ixture ope r a tes : d a m p , s m oky o r p a r tic ula r ly d ir ty
s urr ound ing c a n c a us e g r eat er acc um ula tio n of d ir t on th e u nit’ s optics .
 Cle a n with s oft clo th u s ing no r m a l g l a ss clea ni ng fluid .
 A lw a y s d r y th e parts ca r ef ully .
 Cle a n th e ex ter na l optic s a t leas t ev ery 20 days. Cle a n th e in ter na l opti cs a t
lea s t ev ery 30/60 days.