Osram traxon ecue ARCHISHAPE 2.0 Dot S User manual

ARCHISHAPE®2.0 Dot S/M/L
INSTALLATION GUIDE
V1.0
Cover:
ARCHISHAPE®2.0 Dot S/M/L (ETL)

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 2 of 20
Content
1. Safety And Operation 3
2. Introduction 4
3. Installation 9
4. System Configuration 15
5. Care and Maintenance 17
6. Technical Specification 18
7. Troubleshooting 19
8. Warranty Statement 19
For your own safety and that of the product, please read this installation guide carefully before
beginning setup and installation.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 3 of 20
1. Safety And Operation
1. CAUTION - Unplug the power supply from the mains power before connecting or disconnecting any cables
as this can damage the products.
2. CAUTION - Avoid looking directly into the LED light source at close range for your own safety.
3. Persons installing this product should make sure:
a. The installation complies with all applicable codes, state and local laws, ordinances, standards
and safety regulations.
b. The installation environment is carefully studied and suitable surge protection measure(s) is
taken.
c. He or she is qualified for the handling of electrical equipment.
4. Do not attempt to install or use the product until installation instructions and safety labels are fully understood.
This product is designed for indoor and outdoor use.
5. Ensure product operates within the specified temperature range. (Refer to 6. TECHNICAL SPECIFICATION for
more details.)
6. Do not attempt to open the product. Not user serviceable.
7. Do not use the product if any part of it, or the power cables are damaged.
8. Only use product for specified voltage, do not exceed. (Refer to 6. TECHNICAL SPECIFICATION for more
details.)
9. Always maintain connection to ensure waterproofing.
10. If the product has been subjected to drastic temperature variances, for example, following transportation, do
not connect the fixture until it has reached room temperature, as moisture condensation may cause electric
shock and product damages.
11. When installing the products and system power supplies, please ensure they will not be exposed to moisture
and extreme heat (and direct sunlight for outdoor products). Besides, keep a clean operating environment for
the fixtures and system power supplies.
12. Please study this Installation Guide thoroughly and check the latest Technical Specification Sheets available
from the Traxon website www.osram.us/traxon before setup.
13. Any non-compliance of the Installation Guide will void the Traxon warranty.
Please read through Safety and Operation before start of the installation.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 4 of 20
2. Introduction
2.1 General
ARCHISHAPE®2.0 Dot is a high-brightness, fully customizable media dot solution available in S, M or L with Clear or
Diffused View lens to meet your project specifications. Each Dot is individually-addressable making ARCHISHAPE®
2.0 Dot a durable, scalable solution for vivid accents, graphics and video playback in installations of any size and
complexity.
Features:
— DMX512 Control
— Daisy Chain System
— Auto-Addressing with optional accessory & e:cue Controls
— IP66; IK09; ANSI 3G
— Suitable for irregular surfaces, planes, and configurations

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 5 of 20
2.2 Dimensions
FIG.1: ARCHISHAPE®2.0 Dot S/M/L
AS 2.0 Dot S AS 2.0 Dot M AS 2.0 Dot L
Clear View
14.4mm/0.57”
14.4mm/0.57”
38.4mm/1.51”
AS 2.0 Dot S AS 2.0 Dot M AS 2.0 Dot L
Diffused View
10mm/0.39”
29.3mm/1.15”
14.3mm/0.56”
10mm/0.39”
29.3mm/1.15”
14.5mm/0.57”
35.5mm/1.40”
53mm/2.09”
26mm/1.02”
19mm/0.75”
12mm/0.47”
12mm/
0.47”
52.2mm/2.06”
41mm/1.61”
40mm/1.57”
φ68mm/2.68”
4 x φ3.3mm/0.13”
12mm/
0.47”
55mm/2.17”
41mm/1.61”
4 x φ3.3mm/0.13”
φ71mm/2.80”
45mm/1.77”
19mm/0.75”
53mm/2.09”
26mm/1.02”
12mm/0.47”
4 x φ3.3mm/0.13”
41mm/1.61”
40mm/1.57”
φ68mm/2.68”
12mm/
0.47”
52.2mm/2.06”
4 x φ3.3mm/0.13”
φ71mm/2.80”
41mm/1.61”
45mm/1.77”
12mm/
0.47”
55mm/2.17”
19.6mm/0.77”
25.5mm/1.00”
3.2mm/0.13” 3.2mm/0.13” 3.2mm/0.13”
19.5mm/0.77”
3.4mm/0.53”
3.2mm/0.13” 3.2mm/0.13”
3.2mm/0.13”
Mounting bracket
Mounting bracket
∅∅

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 6 of 20
FIG.2: ARCHISHAPE®2.0 Dot S/M/L Accessories
AS Dot End Cap with Resistor ( AM345880055 ) Starter Cable 16ft / 5m ( AM345860055 )
500mm (19.69")
47.2mm (1.86")
∅18mm (0.71")
12mm (0.47")
RED (1.0mm²)
GREEN (0.25mm²)
YELLOW (0.25mm²)
BLUE (0.25mm²)
BLACK (1.0mm²)
FEMALE CONNECTOR
30mm (1.18")
∅17.1mm (0.67")
∅15.6mm (0.61")
Interconnection Cable ( AM460720055 )
FEMALE CONNECTOR FEMALE CONNECTOR
∅18mm (0.71")
47.2mm (1.86") 1000mm (3.28') 47.2mm (1.86")
12mm (0.47")
18mm (0.71")
AS Dot S Mounting Clip ( AM357440055 )
19mm (0.75")
29.3mm (1.16")
10mm (0.39")
∅1.9mm (0.08”)
∅3.6mm (0.14")
Auto-addressing module (4ch AM345890055) (3ch AM456250055)
4X 5mm (0.20”)
∅
67.5mm (2.66")
61.5mm [2.42"]
∅106.5mm (4.19")
∅18mm (0.71")
48mm (1.89")
170mm (6.69")
170mm (6.69")
18mm (0.709")
MALE CONNECTOR FEMALE CONNECTOR
RJ45 Power Injector Cable Kit ( AM357480055 )
42.8mm (1.69")
M17*1.0
∅19.6mm (0.77")
∅12mm (0.47")
300mm ± 20mm (11.81"± 0.79")
59.2mm (2.33")
∅18mm (0.71")
∅6.0mm (0.24")
∅7.2mm (0.28")
48mm (1.89")
150mm±10mm (5.91" ± 0.39")
22mm (0.87")
47mm (1.85")
18mm (0.71")
48mm (1.89") 39mm (1.54")
MALE CONNECTOR
MALE CONNECTOR
TIGHTENING TORQUES: 0.7~0.9N.m
∅∅
∅
FEMALE CONNECTOR

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 7 of 20
∅∅∅∅
∅
∅"
∅
∅
∅
Power Injector Cable Kit (
AM460710055 )
45.5mm (1.79")
∅∅
∅
∅
∅
∅7.2mm (0.28")
TIGHTENING TORQUES: 0.7~0.9N.m
18mm (0.71")
∅12mm (0.47")
17.7mm (0.70") 22mm (0.87")
59.2mm (2.33")
∅18mm (0.71")
MALE CONNECTOR
MALE CONNECTOR
FEMALE CONNECTOR
300mm ± 20mm (11.81"± 0.79")
47mm (1.85")
150mm±10mm (5.91" ± 0.39")
48mm (1.89")
48mm (1.89")
FIG.3: ARCHISHAPE®2.0 Dot S/M/L String
FEMALE CONNECTORMALE CONNECTOR
150mm (5.91")
47.2mm (1.86")
∅
18mm (0.71")
∅
18mm (0.71")
500mm (19.69")
48mm (1.89")
12mm (0.47")
FEMALE CONNECTORMALE CONNECTOR
150mm (5.91")
47.2mm (1.86")
∅18mm (0.71")
∅
18mm (0.71")
500mm (19.69")
48mm (1.89")
12mm (0.47")

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 8 of 20
2.3 Packing Contents
FIG.4: ARCHISHAPE®2.0 Dot S/M/L Packing Contents
ARCHISHAPE®2.0 Dot S/M/L
FIG.5: RJ45 Power Injector Cable Kit Contents
RJ45 Power Injector Cable Kit

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 9 of 20
3. Installation
3.1 Points To Consider
Plan your installation before mounting any luminaires. The following should be considered for a successful
installation.
— Weather conditions and ambient temperature of installation site.
— Appropriate cable lengths
— Adequate space for heat dissipation (150mm / 6” apart) of LED Engines (see “3.3 On-Site Installation” on page
12).
— Appropriate anchor bolts where necessary to secure the ARCHISHAPE®2.0 Dot S/M/L.
— The number of ARCHISHAPE®2.0 Dot S/M/L and LED Engines.
— Controller to be used to control the ARCHISHAPE®2.0 Dot S/M/L.
3.2 Pre-Installation Checks
3.2.1 Installation Checklist
1. Prepare cables and all necessary accessories.
2. Perform functional check of ARCHISHAPE®2.0 Dot S/M/L.
3. Ensure the connector of last dot is covered by the End Cap Resistor.
4. Ensure all pre-installation checks laid out below have been followed.
5. Mount the ARCHISHAPE®2.0 Dot S/M/L on-site. If the installation is to be left uncompleted overnight, place
all non-connected LED Engines and ARCHISHAPE®2.0 Dot S/M/L in an indoor environment.
Ensure all the Connection Cables, ARCHISHAPE®2.0 Dot S/M/L are initially stored in a dry area to guarantee the
complete sealing of the system from water before installation.
Connector should be properly connected with cable connectors and the connector of last dot should be covered
by its Waterproof End Cap to ensure IP66 rating.
3.2.2 Handling The ARCHISHAPE®2.0 Dot S/M/L String
When transporting or preparing the ARCHISHAPE®2.0 Dot S/M/L string, please handle with care. To reduce
stress on cables, carry by the ARCHISHAPE®2.0 Dot S/M/Ls and not the cable during transit.
FIG.6: Correct way of handling ARCHISHAPE®2.0 Dot S/M/L String
Allow slack on cable to
reduce stress

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 10 of 20
3.2.3 Requirements Of Cable Bending And Twisting
Please take EXTRA precautions before bending or twisting ARCHISHAPE®2.0 Dot S/M/L cable. Lead Cable must
NOT be bent below the Minimum Bending Radius (4x Cable Diameter) and the Non-Bendable Length of 50mm /
2” near the connector end or near the cable overmold MUST be adhered to.
FIG.7: Minimum Cable Bending and Non-Bendable Length Requirement
(Non-Bendable Length)
500mm (19.69")
≥
4D
(Minimum Bending Radius)
14mm/0.55”
20mm/0.79”
D
Ø7mm/0.28”
50mm/1.97”
(Minimum Bending Radius)
28mm/1.00”
≥
4D
The flat ARCHISHAPE®2.0 Dot S/M/L Cable must NOT be bent/twisted below 20mm (0.79”) from edge of
ARCHISHAPE®2.0 Dot S/M/L housing (Non-Bendable/Non-Twistable Length).
Twisting the flat cable is NOT recommended. If twisting is necessary for installation, please adhere to the Non-
Twistable Length specified in Fig. 6 and ensure the mounting pitch is greater than or equal to 75% of the normal
ARCHISHAPE®2.0 Dot S/M/L to ARCHISHAPE®2.0 Dot S/M/L pitch. The middle part of the cable must be
secured to the mounting surface with a cable tie (see “3.3 On-Site Installation” on page 12 and FIG.11 on page
14). Ensure no damage is generated on the cable.
FIG.8: Minimum Clearance
20mm/0.79”
Minimum clearance
from dot
Non-Bendable/
Non-Twistable Length
NOTE: Water ingress incurred due to excess cable bending/twisting will not be warrantied by Traxon Technologies.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 11 of 20
3.2.4 Installation Sequence
1. Plan for any possible bending of cables (refer to “3.2.3 Requirements Of Cable Bending And Twisting” on
page 10 as well as Fig. 11 on page 14.).
2. Always keep the End Cap Resistor safe in a container for reuse.
3. Connect ARCHISHAPE®2.0 Dot S/M/L with system components and LED Engines as outlined within this
guide. See section 4 for System Diagrams.
4. Perform functional check on all ARCHISHAPE®2.0 Dot S/M/L and inspect cables for any damage. Check for
any abnormalities with the signal.
5. Report any functional defect found to your nearest Traxon Technologies office. DO NOT attempt to install
ARCHISHAPE®2.0 Dot S/M/L with functional defects on-site.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 12 of 20
3.3 On-Site Installation
— DO NOT attempt installation in wet or severe weather conditions.
— DO NOT leave and expose any ARCHISHAPE®2.0 Dot S/M/L, or LED Engine
unconnected under wet/raining or snowing environment.
— DO NOT pull on cable of ARCHISHAPE®2.0 Dot S/M/L. IP failure induced by stressed/
damaged cables during or after installation will not be warrantied by Traxon Technologies.
— ALWAYS keep the cables protected from sharp objects and ensure no damage is
generated on the cable.
— Failure to keep ARCHISHAPE®2.0 Dot S/M/L within the operating temperature range of
-20°C to + 50°C/-4°F to +122°F, and storage temperature range of -40°C to + 80°C/-
40°F to +176°F will void the product’s warranty.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 13 of 20
3.3.1 Mounting ARCHISHAPE®2.0 Dot S/M/L
1. ARCHISHAPE®2.0 Dot S/M/L must be mounted ensuring that no stress is placed on the cable. Follow the
data provided in section 3.2.3
2. ARCHISHAPE®2.0 Dot S/M/Ls MUST be mounted to the installation surface via the mounting holes, either by
screw or cable tie.
FIG.9: Mounting the ARCHISHAPE® 2.0 Dot S/M/L
1
2b-3
“click”
2a AS 2.0 Dot M/L mounting
2b-1 AS 2.0 Dot S mounting 2b-2
Screws are provided by others
Screws are provided by others

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 14 of 20
3. Cable segment must not be bent below 20mm / 0.79” from the housing of the ARCHISHAPE®2.0 Dot S/M/L
and cable overmold (Minimum Bending Length).
4. Secure the excess cable between Dots (every 500mm / 19.7”, using cable tie) to ensure no damage is
generated due to hanging cable.
FIG.10: Securing the cable
Observe clearance
Cable tie
Mounting surface
5. If the cable between ARCHISHAPE®2.0 Dot S/M/L requires twisting due to a change in mounting direction,
ensure the mounting pitch after-twisting is more than or equal to 75% of the normal Dot to Dot pitch.
FIG.11: Twisting requirements
≥75% L
Non-Twistable Length
20mm/0.79”
L = Length of cable
Secure center of
cable with cable tie
≥75% L
Non-Twistable Length
20mm/0.79”
L = Length of cable Non-Twistable Length
Secure center of
cable with cable tie

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 15 of 20
4. System Configuration
FIG.12: System Diagram – Basic
End Cap Resistor (AM345880055)
DMX In
AC in
RJ45 Power Injection Cable Kit (AM357480055)
LED Engine 24V
FIG.13: System Diagram – Power Injection
DMX In
AC in
Power Injection Cable Kit (AM460710055)
AC in
LED Engine 24V
LED Engine 24V
RJ45 Power Injection Cable Kit (AM357480055)
End Cap Resistor (AM345880055)
Power injection is required to extend the data run by interconnecting two ARCHISHAPE®2.0 Dot S/M/L units.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 16 of 20
FIG.14: System Diagram – Auto-addressing Module
Auto-addressing module
(4ch AM345890055)
(3ch AM456250055)
DMX In
AC in
LED Engine 24V
RJ45 Power Injection Cable Kit (AM357480055)
End Cap Resistor (AM345880055)
Auto-Addressing requires e:cue Controls.
FIG.15: System Diagram – Junction box
DMX In
LED Engine 100W 24V Outdoor
(AM175860055)
AC 120V - 277V In
AS Dot Starter Cable 5M White
(AM345860055)
End Cap Resistor (AM345880055)
Green DMX+
Red 24V+
Blue Address
Yellow DMX-
Black 24V- & GND
Connector Details

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 17 of 20
5. Care and Maintenance
Traxon products are of superior design and quality and should be treated with care. The recommendations below
will help fulfill any warranty obligations and gain longevity from the products.
— Do not attempt or use the product(s) until you read and understand the installation instructions. Failure to
adhere to these instructions could result in serious injury or property damage.
— Do not use product(s) if cables are damaged.
— Do not connect cables and connectors when wet or in wet area. Moisture on bare connectors can cause
electric shock and damage to product(s).
— Do not use product(s) in extreme heat environment. Ensure there is sufficient airflow and use cool air circulation
if required.
— Do not drop, knock, or shake product(s). Rough handling can damage the electronics and void the warranty.
— Do not use harsh chemicals, cleaning solvents, or strong detergents to clean products. Wipe with a damp
cloth on housings and a dry cloth on electronics to remove dirt or dust.
— Do not attempt to service or repair the product(s) unless done by an authorized service personnel. Contact
your local Traxon office or distributor for details.
— If the product is not working as specified, please contact your nearest Traxon Technologies office for
assistance.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 18 of 20
6. TECHNICAL Specification
Model (Clear View) ARCHISHAPE®2.0 Dot S ARCHISHAPE®2.0 Dot M ARCHISHAPE®2.0 Dot L
Color Range: RGB, RGBW (White CCT: 6500K)
Light Source: 3RGB
3RGB + 1W
6RGB
4RGB + 2W
9RGB
6RGB + 3W
Beam Angle: 110° 110° 110°
Power Input: 24V DC
Power
Consumption1:
1W 2W 3W
Weight (Dot): 28.2g / 0.06lb 66.9g / 0.15lb 73.6g / 0.16lb
Operating
Temperature:
-20°C to + 50°C/-4°F to +122°F
Storage
Temperature:
-40°C to + 80°C/-40°F to +176°F
Model (Diffused View) ARCHISHAPE®2.0 Dot S ARCHISHAPE®2.0 Dot M ARCHISHAPE®2.0 Dot L
Color Range: RGB, RGBW (White CCT: 6500K)
Light Source: 3RGB
3RGB + 1W
6RGB
4RGB + 2W
9RGB
6RGB + 3W
Beam Angle: 150° 150° 150°
Power Input: 24V DC
Power
Consumption1:
1W 2W 3W
Weight (Dot): 28.2g / 0.06lb 66.9g / 0.15lb 73.6g / 0.16lb
Operating
Temperature:
-20°C to + 50°C/-4°F to +122°F
Storage
Temperature:
-40°C to + 80°C/-40°F to +176°F
1. Measurement per dot.
As with all electronic devices, LED output degrades over time - a term called lumen depreciation. This also
explains why it is nearly impossible to expect photometric performances of two LED products with different service
life spans to be the same. The rate of LED degradation is a complex function of many factors such as operating
efficiency, duration of continuous operation, and operating conditions (e.g. ambient temperature).
Because LEDs are semiconductor devices, their performances are subject to inherent variability commonly found
in semiconductor industry. To improve consistency in performance across the same product, LED manufacturers
“sort” LEDs into bins according to different preset parameters, such as forward driving voltage, illumination,
etc. Whereas binning is a sorting function, it is not a correction process. Inherent variability in the manufacturing
process always results in different binning distributions according to different production lots. Traxon uses
automatically binned LEDs on its products, thereby minimizing output variations within the model range.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide 01/22 V1.0 19 of 20
7. Troubleshooting
CAUTION: Ensure power supply is OFF when disconnecting / connecting cables.
Problem Cause Possible Solutions
Product does
NOT light up after
installation
Incorrect power connection — Check Mains Power
— Check power supply leads and wire connections
— Ensure output wires are connected with proper
polarity
Shadowing Light source covered — Adjust pitch between ARCHISHAPE®2.0 Dot
S/M/L strings
— Check for cables, wires or unwanted debris
covering LED light source
Modules are dim Excess products connected — Ensure the power supplies are not overloaded due
to an excess of products connected
— Ensure power supply with proper voltage (24v) is
being utilized.
Flickering Incorrect power input/Excess
products connected
— Ensure the input voltage is correct
— Ensure the power supplies are not overloaded due
to an excess of products connected
If problems persist or the product is not working as specified, please contact your Traxon Technologies office for
assistance.
8. Warranty Statement
Traxon Technologies warrants its Products against material or workmanship defects for a period of five (5) years
from date of purchase, provided that the purchased items are used under the conditions stated in this user
manual.
Please refer www.osram.us/traxon for all warranty terms and conditions.

Please check for the latest updates and changes on the Traxon website.
© 2022 TRAXON TECHNOLOGIES ALL RIGHTS RESERVED. Information is subject to change without prior notice.
www.traxontechnologies.com | www.osram.us/traxon