Osram 3240G4 User manual

3240G4
32x40W Wall Washer RGBW 4in1 LED Light
User manual
P le a se rea d t he ins t r u ction s ca refu ll y before use

2
TABLE OF CONTENTS
1. S af ety I nst r uctions ................................................................................................. 3-4
2. Technical Specifications .......................................................................................... 5
3. How To Control The Unit ....................................................................................6-12
4. shape ........................................................................................................................11
5. Trouble shooting ..................................................................................................... 14
6. Fixture Cleaning ......................................................................................................14
statement
The product has well capability and intact packing when leave factory. All of the
user should comply with warning item and manual, any misuse cause of the
damages are not included in our guarantee, and also can’t be responsible for
any malfunction & problem owing to ignore the manual.

3
1. S af ety I nst r uctions
Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
 Unpack and check carefully there is no transportation damage before using
the unit.
 Before operating, ensure that the voltage and frequency of power supply match
the power requirements of the unit.
 It’s important to ground the yellow/green conductor to earth in order to avoid
electric shock.
 The unit is for indoor use only. Use only in a dry location.
 The unit must be installed in a location with adequate ventilation, at least 50cm
from adjacent surfaces. Be sure that no ventilation slots are blocked.
 Disconnect main power before replacement or servicing.
 Make sure there are no flammable materials close to the unit while operating as
it is fire hazard.
 Use safety cable when fixes this unit. Do not handle the unit by taking its head
only, but always by taking its base.
 Maximum ambient temperature is Ta: 40℃. Do not operate it where the
temperature is higher than this Unit surface temperature may reach up to 85℃.
Do not touch the housing bare-hand during its operation. Turn off the power and
allow about 15 minutes for the unit to cool down before replacing or serving.
 In the event of serious operating problem, stop using the unit immediately.
Never try to repair the unit by yourself. Repairs carried out by unskilled
people can lead to damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the same type spare
parts.

4

Do not touch any wire during operation as high voltage might be causing electric
shock.
Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to
rain or moisture.

Do not open the unit within five minutes after switching off.

The housing, the lenses, or the ultraviolet filter must be replaced if they are
visibly damaged.
Caution:
There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require
service, please contact your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that
the unit is firmly fixed to avoid vibration and slipping while operating. And make
sure that the structure to which you are attaching the unit is secure and is able to
support a weight of 10 times of the unit’s weight. Also always use a safety cable
that can hold 12 times of the weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place
where is out of the touch of people.

5
2. Technical Specifications
Light Sources: 32 x 60W 4in1 RGBW LED
Light Angle: 38°
COB + PMMA High Quality Optical Lens
Power Consumption: 1050W
Power Voltage: AC 100-240V, 50/60Hz
Dimension: 514*222*324 mm
Net Weight: 15 kg
Gross Weight: 20 kg Size:62*43*34.5cm (Carton package 1in1)
Gross Weight:75.65 kg Size:80*68.5*53cm (Flight case package 3in1)
Control
DMX Channel: 9/14 Channels
Control Modes: DMX512/Master-Slave/Auto Run/Music/RDM/Manual
Pan/Tilt
Pan/Tilt: 540°or 360°in optional / 270°
Pan/Tilt Resolution: 8/16 bit
Construction
Display:1.8 TFT colorful Display
Data In/Out socket: 3-pin XLR sockets
Power Socket: Power Con in/out
Protection Rating: IP65
Features
Full optical domain dimming, with 65536 level dimming accuracy;
Fast strobe 1-25Hz; Preset multiple color macro effect ;
Dimmer: 0~100% smooth dimming

6
3. How To Control The Unit
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
Set DMX Address Code
1 Press "Menu" to "Set DMX Address", and press "ENTER" keys to enter into
2 Show "Set DMX Address DMX Address:001", Press the "UP and DOWN"
keys to amended
3 Press "ENTER" keys to save and Exit, Press the "MENU" Keys does not save
and Exit
1.Mic Sense
001--100
Sound control adjust
sensitiveness
2.Language
1.English
2.Chinese
3.No Signal
1.Black Out

7
Menu
2.Hold
4. Fan Set
1. Auto
2. Low
3. High
5.Default
1.Yes
2.No
6.Adjust
Pass Word
****
1.Red：0--255
Changing the value
of R/G/B/W can
adjust the white
balance, but the value
can’t be set to zero
2.Green：0--255
3.Blue：0--255
4.White：0--255
Address
Set address code 001--512
Rever
2..Display
1.Yes
Display forward
and reverse
2.No
Inform
1.CH Value
Display all channel values
2.Temp/℃
Display led board
temperature
3.Soft v.xxx
Software version number
Mode
1.DMX512
2.Auto
1.Master

8
2.Alone
3.Sound
1.Master
2.Alone
4.Manual
Master
1.Red：0--255
2.Greed：0--255
3.Blue：0--255
4.White：0--255
Alone
5. Strobe：0-255
Channel
1.9Channels
2.14Channels
DMX channel´s functions and values (9/14DMX channels):
Channel Model 1 - CH9
Channel
Display
Function
Value
CH-1
Dimming
From dark to bright
0 --- 255
CH-2
Strobe
Light up
0 --- 3
From slow to fast
（1HZ-25HZ）
4 --- 203
Random strobe
204 --- 255
CH-3
Red
From dark to bright
0 --- 255

9
CH-4
Green
From dark to bright
0 --- 255
CH-5
Blue
From dark to bright
0 --- 255
CH-6
White
From dark to bright
0 --- 255
CH-7
Linear Color
Temperature
No
0----4
Color temperature from
warm to cool
5-----255
CH-8
Macro Color
No
0-----9
Macro Color-1
10----14
Macro Color-2
15----19
..........
......5
numbers 1
effect
Macro Color-14
75----79
Macro Color-15
80----255
CH-9
Dimming
Model
Model -1
0 --- 49
Model -2
50 --- 99
Model -3
100 --- 149
Model -4
150 --- 255

10
Channel Model 2 – CH14
Channel
Display
Function
Value
CH-1
Red
From dark to bright
0 --- 255
CH-2
Red adjustment
Red adjustment
0 --- 255
CH-3
Green
From dark to bright
0 --- 255
CH-4
Green
adjustment
Green adjustment
0 --- 255
CH-5
Blue
From dark to bright
0 --- 255
CH-6
Blue adjustment
Blue adjustment
0 --- 255
CH-7
White
From dark to bright
0 --- 255
CH-8
White
adjustment
White adjustment
0 --- 255
CH-9
Dimming
From dark to bright
0 --- 255
CH-10
Dimming
adjustment
Dimming adjustment
0 --- 255
CH-11
Strobe
Light up
0 --- 3
From slow to fast
（1HZ-25HZ）
4 --- 203
Random strobe
204 --- 255
Linear Color
Temperature
No function
0----4

11
CH-12
Color temperature from
warm to cool
5-----255
CH-13
Macro Color
No
0 --- 9
Macro Color-1
10-- 14
Macro Color-2
15-- 19
..........
5 numbers
1 effect
Macro Color -14
75 --- 79
Macro Color-15
80--- 255
CH-14
Dimming Model
Model -1
0 --- 49
Model -2
50 --- 99
Model -3
100 --- 149
Model -4
150 --- 255

12
4. LUX

13
5.Shape
6. Trouble shooting

14
Following are a few common problems that may occur during operation. Here are
some suggestions for easy troubleshooting:
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. N o t responding t o D MX c on t ro ll er
1. DMX LED should be on. If not, check DMX connectors, cables to see if link
properly.
2. If the DMX LED is on and no response to the channel, check the address settings
and DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on
PCB of the unit or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that
may cause damage or interference to DMX interface circuit.
C . One of the cha nn el s is no t w o r k ing w el l
1. The stepper motor might be damaged or the cable connected to the PCB is
broken.
2. The motor’s drive IC on the PCB might be out of condition.
6. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried
out periodically to optimize light output. Cleaning frequency depends on the
environment in which the fixture operates: damp, smoky or particularly dirty
surrounding can cause greater accumulation of dirt on the unit’s optics.
 Cle a n with s oft clo th u s ing no r m a l g l a ss clea ni ng fluid .
 A lw a y s d r y th e parts ca r ef ully .
 Cle a n th e ex ter na l optic s a t leas t ev ery 20 days. Cle a n th e in ter na l opti cs a t
lea s t ev ery 30/60 days.