Osram ARCHISHAPE 2.5 Washer User manual

ARCHISHAPE® 2.5 Washer
ARCHISHAPE® 2.0 Linear
DMX and RDM Configuration Guide
Cover:
ARCHISHAPE®2.5 Washer
ARCHISHAPE®2.0 Linear
Preliminary

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
DMX/RDM Configuraion Guide 07/19 / V0.1 2 of 10
TABLE OF CONTENTS
For your own safety and that of the product, please read this configuration guide
carefully before beginning setup and installation.
1. INTRODUCTION 3
2. CONNECTION 3
2.1 TOOLS 3
2.2 TYPICAL CONNECTION DIAGRAM (WITH BUTLER S2) 3
3. E:CUE PROGRAMMER CONFIGURATION 4
4. AUTO-ADDRESSING 6
4.1 EXPERT SETUP 6
4.2 AUTO-ADDRESSING CONFIGURATION 7
5. RDM CONFIGURATION (OPTIONAL) 9

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
DMX/RDM Configuraion Guide 07/19 / V0.1 3 of 10
1. INTRODUCTION
ARCHISHAPE®2.5 Washer and ARCHISHAPE®2.0 Linear allow users to configure the
luminaire through the e:cue programmer easily. Major feature that can be configured include:
• DMX Auto-addressing
2. CONNECTION
2.1 Tools
• e:cue Programmer (part of Lighting Application Suite, need USB dongle to use ActionPad)
• Butler S2
2.2 Typical Connection Diagram (with Butler S2)
FIG.1: Typical Connection Diagram (with Butler S2)
Butler S2e:cue Programmer
Butler S2
DMX/RDMOutput Engine
e:net DMX512
~Mains AC ~Mains AC
RJ45 Plug
Pin 2: DMX+
Pin 3: GND
Pin 1: DMX–
DC Power Supply
GND
(Yellow/Green)
DMX−
(Blue)
DMX+
(Brown) ARCHISHAPE®2.0 Linear
ARCHISHAPE®2.5 Washer
Luminaire

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
DMX/RDM Configuraion Guide 07/19 / V0.1 4 of 10
3. E:CUE PROGRAMMER CONFIGURATION
1. Open e:cue Programmer (V7.0 or higher).
2. Go to “Application Options” under the “Advanced” top menu.
3. Click “Advanced”.
4. Make sure the “e:net” setting is in the same network for Butler S2. For example, if IP
of Butler S2 is 172.16.17.201, then the IP of host computer should be 172.16.17.XXX,
which XXX can be any values from 1 to 254.
FIG.2: Application Options
5. Click “Device Manager”.
FIG.3: Device Manager

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
DMX/RDM Configuraion Guide 07/19 / V0.1 5 of 10
6. Click “Automatic Device Setup Wizard”, then click “OK” if the Butler S2 is detected:
FIG.4: Auto Setup
7. Then the Butler S2 will be “Online” in “Device Manager”.
FIG.5: Device Manager

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
DMX/RDM Configuraion Guide 07/19 / V0.1 6 of 10
4. AUTO-ADDRESSING
4.1 Expert Setup
1. Select “Application Suite” > “Toolbox”.
FIG.6: Toolbox
2. Click “Expert Setup”.

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
DMX/RDM Configuraion Guide 07/19 / V0.1 7 of 10
FIG.7: Expert Setup
3. Set “universe_max” to 128 and “desk_channel_max” to 65536.
4. Click “OK”.
4.2 Auto-addressing Configuration
1. Open a show file and detect any online device in the “Device Manager”.
2. Click the “Auto Detect Wizard” icon, and then set the detected device as the output
device.

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
DMX/RDM Configuraion Guide 07/19 / V0.1 8 of 10
FIG.8: Auto Setup
3. Right-click and select “Properties” to check each device properties.
The output universe should be 1 and other universes should start from 2. The number
increases when more devices are connected.
FIG.9: Device Properties
4. Click “OK”.
5. Press CTRL + F2 to open the Action Pad.

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
DMX/RDM Configuraion Guide 07/19 / V0.1 9 of 10
FIG.10: Action Pad
6. Enter the DMX Address and Number of DMX Universe.
7. Click “Patch”.
The Patch button turns orange.
8. Click “Set Cmd” and wait for a few seconds.
9. Click “Send Cmd” and wait for a few seconds.
When the auto-addressing is complete, the first 16 DMX channels of each universe
should be 128. The fixtures will turn on accordingly.
5. RDM CONFIGURATION (OPTIONAL)
1. Click “RDM Manager”, all ports are default disabled with RDM function.
2. Right click “Butler2”, then select “Enable RDM”.
3. The interface will then list out all RDM devices connected to the Butler S2:
FIG.11: RDM Manager
NOTE: RDM configuration only supports the luminaires with RDM function.

Information is subject to change without prior notice.