OSS OSS-KIT-EXP-6002 User manual

Host Server to Expansion System Kit User Manual
OSS-KIT-EXP-6002
SKU: OSS-KIT-EXP-6002
www.onestopsystems.com

One Stop Systems
OSS-KIT-EXP-6002| 2
Table of Contents
1 Overview .......................................................................................................................................................................... 3
1.1 Description.................................................................................................................................................................................................... 3
1.2 Features .................................................................................................................................................................................................... 4
1.1.1 Adapter Cards................................................................................................................................................................................. 4
1.1.2 x4 Link Cable................................................................................................................................................................................... 4
1.3 Specifications ............................................................................................................................................................................................ 5
1.3.1 Host Adapter .................................................................................................................................................................................. 5
1.3.2 Expansion Link Board ..................................................................................................................................................................... 5
1.3.3 PCIe x4 Cable.................................................................................................................................................................................. 6
2 Component Identification ................................................................................................................................................. 7
2.1 Host cable adapter card ............................................................................................................................................................................ 7
2.2 Expansion Link Board ................................................................................................................................................................................ 7
3 Installation Instructions .................................................................................................................................................... 8
3.1 Installing the Adapter Kit............................................................................................................................................................................... 8
3.2 Expansion link board ..................................................................................................................................................................................... 8
3.3 Removing PCIe Cable..................................................................................................................................................................................... 8
3.4 Operation...................................................................................................................................................................................................... 8
4 Technical Information ....................................................................................................................................................... 9
4.1 Signal Adjustment ......................................................................................................................................................................................... 9
4.2 Pin Assignments ............................................................................................................................................................................................ 9
4.3 Pin-out for the PCIe x4 Card Edge Connector on the “Host Cable Adapter” ............................................................................................... 10
4.4 PCI Express x4 Connector PIN Assignment.................................................................................................................................................. 11
4.5 Pin-out for the PCIe x4 Cable ...................................................................................................................................................................... 11
4.6 Signal Descriptions ...................................................................................................................................................................................... 12
4.7 Connector Pin-outs for the PCIe x4 Cable Connector.................................................................................................................................. 12
4.8 PCI Express x4 Connector PIN Assignment.................................................................................................................................................. 13
5 Contacting Technical Support ..........................................................................................................................................14
6 Returning Merchandise to One Stop Systems ..................................................................................................................14

One Stop Systems
OSS-KIT-EXP-6002| 3
1 Overview
1.1 Description
The PCIe x4 expansion kit is used to extend the PCI express bus from a host server to an external expansion chassis. The host adapter card
inserts into a PCIe slot of the server. It then cables to a downstream expansion link board (ELB). The ELB acts as a downstream cable link board
and the primary fan-out switch to support multiple configurations of PCI express expansion slots. The host adapter installs into a PCIe x4, x8 or
x16 slot on the host motherboard. It then cables to the expansion link board and installs in the SHB or system slot of a CPCIe backplane.

One Stop Systems
OSS-KIT-EXP-6002| 4
1.2 Features
1.1.1 Adapter Cards
The Host adapter card inserts into any PCI Express x4, x8, 16 slot on the host motherboard.
The Target adapter card fits into SHN slot of PICMG 1.3 backplane..
Support half-height bracket.
The Host and Target cable adapter cards require no software / drivers
1.1.2 x4 Link Cable
Available in 1m, 2m, 3m, 5m, 7m lengths.
PCI-SIG Express Cable Specification Compliant.
Includes x4 PCIe lane and side-band signals for:
oPower ON
oReset
oPCIe clock
oCable Present
oWake
Positive latching mechanism per PCI-SIG specification
Support 10 Gbps full-duplex transfer rates.

One Stop Systems
OSS-KIT-EXP-6002| 5
1.3 Specifications
1.3.1 Host Adapter
PCIe x4 Host Cable Adapter Card (SKU : OSS-PCIe-HIB25-X4-H)
Form Factor
PCIe x4 add-in card
Dimension (H x L)
2.7” x 3.1” (68 x 78mm)
Front Panel Connectors
One PCIe x4 cable connectors
Front Panel Indicators
Power ON / Cable Present LED
Red-drivers
Pericom P12EQX5804
Temperature Range
0° to 50°C (32° to 122°F)
Relative Humidity
10 to 90% non-condensing
Shock
30g Acceleration peak (11 ms pulse)
Vibration
5-17 Hz 0.5” double amplitude displacement; 7-2000Hz, 1.5g acceleration
Power Consumption
3.75W typical, [email protected]
Agency Compliance
UL60950, FCC Class B, CE safety and emissions, ROHS
Redriver
Pericom P12EQX5804
1.3.2 Expansion Link Board
PCIe x4/x8 Gen2 Expansion Link Board (SKU : OSS-SHB-G2-x8-x4)
Form Factor
PCIMG EXP.system slot compliant. Single Slot
Slot Type
System slot for the expansion chassis
Dimension (H x L)
3.937 x 6.299 in (100 x 160 mm), 1 slot wide
Switch
PLX PEX8733 32 lane switch
Upstream Interface
x4 PCI Express over cable
PCI-SIG PCI Express Cable Rev 2.0 Compliant
Downstream Interface
16 lanes of PCI Express on the backplane connectors.
The lanes form two or four links to the backplane through the XP2 and XP3
connectors per the PICMG EXP.0 specification.
The following link modes are automatically selected by the backplane as follows:
• Two link mode: 2 x8 links (per backplane capabilities)
• Four link mode: Four x4 PCIe links
Front Panel Connectors
1 PCIe x4 Cable (Molex : 75586-0010)
Front Panel Indicators
4 backplane link-active indicators (green)
2 or 4 link mode + cable link (green)
Power Consumption
10W typical +12V @ .5, 3.3V @ 1.25A, 5Vaux @ 2.5mA
Temperature Range
0° to 50°C (32° to 122°F)
Relative Humidity
10 to 90% non-condensing
Storage Temperature
-40° to 85°C (-40°-185°F)
Shock
30g acceleration peak (11ms pulse)
Vibration
5-17 Hz 0.5” double amplitude displacement; 7-2000Hz, 1.5g acceleration
Agency Compliance
UL60950, FCC Class B, CE safety and emissions, ROHS

One Stop Systems
OSS-KIT-EXP-6002| 6
1.3.3 PCIe x4 Cable
PCIe x4 Cable (SKU : OSS-PCIe-CBL-x4.1M) 1 meter long cable
Cable Length
1m, 2m, 3m, 5m, 7m
Circuits loaded
38
Gender
Male-to-Male
Lock to Mating Part
Yes
Material-Metal
Zinc Alloy
Pitch-Mating Interface
0.80mm (0.31)
Single Ended
No
Water proof / Dust
proof
Yes
Wire Insulator
Diameter
N/A
Wire Size AWG
28
Wire / Cable Type
Round
Electrical Current
1A Max per contact
Shielded
Yes
Voltage-Maximum
30V DC

One Stop Systems
OSS-KIT-EXP-6002| 7
2 Component Identification
2.1 Host cable adapter card
The PCIe x4 expansion kit contains two cable adapter boards, the host cable adapter and the target cable adapter. The host adapter inserts into
the host computer’s PCIe x4, x8 or x16 slot.
Cable LED indicators are the same for both Host and Target configurations.
2.2 Expansion Link Board
The Expansion Link Board (ELB) OSS-CPCIe3-3U/6U-ELB-x4 is a downstream link board that installs into a CPCIe chassis. The ELB fits into the
system slot of a CPCIe backplane. The ELB is the downstream link board and the primary fan-out switch to support multiple configurations of
CPCI or CPCIe expansion slots.

One Stop Systems
OSS-KIT-EXP-6002| 8
3 Installation Instructions
3.1 Installing the Adapter Kit
1. Insert the host cable adapter into an appropriate PCIe slot of the host computer. For example, a PCIe x4 host board can be inserted
into a PCIe x16, x8, or x4 slot. It will still operate at x4 speeds. Secure the cable adapter card
3.2 Expansion link board
1. Insert the expansion link board into the SHB slot on the chosen backplane.
2. Connect the x4 PCIe cable to both cables adapter cards. Press or pull the green TAB while slowly inserting the cable, then release it
to lock the cable. See photos below.
3. Test by pulling back on the connector.
3.3 Removing PCIe Cable
1. To remove the cable, press or pull the green tab and slowly pull the cable out.
3.4 Operation
1. Plug in expansion system and turn the power supply on.
2. Power up host computer.
3. The expansion system will power up.

One Stop Systems
OSS-KIT-EXP-6002| 9
4 Technical Information
The transmit and receive signals on the OSS-HIB-25x4 are driven and conditioned by Pericom redriver chips. Adjustments can be made to
equalization, de-emphasis and output swing. These controls are factory set by the use of zero Ohm resistors.
In the following tables, a 0 indicates that a zero Ohm resistor has been installed and a 1 indicates no resistor. In rare cases, mostly where non-
OSS equipment is used with the HIB-25x4, these adjustments may need to be changed. The following tables are made available for this
purpose. It is highly recommended to contact OSS customer support before making changes to these settings. Having the customer solder to
the board should void the warranty.
4.1 Signal Adjustment
4.2 Pin Assignments
Host and Target card connectors (x4 Card Edge Connector)
The pins are numbered as shown with side A on the top of the centerline on the solder side of the board and side B on the bottom of
the centerline on the component side of the board.
The PCIe interface pins PETpx, PETnx, PERpx, and PERnx are named with the following convention: “PE” stands for PCIe high speed,
“T” for Transmitter, “R” for Receiver, “p” for positive (+), and “n” for negative (-).
Note that adjacent differential pairs are separated by two ground pins to manage the connector crosstalk.

One Stop Systems
OSS-KIT-EXP-6002| 10
4.3 Pin-out for the PCIe x4 Card Edge Connector on the “Host Cable Adapter”
Pin
#
Side B
Side A
Name
Description
Name
Description
1
N/C
N/C
PRSNT1#
Hot-Plug presence detect
2
N/C
N/C
N/C
N/C
3
N/C
N/C
N/C
N/C
4
GND
Ground
GND
Ground
5
NC
N/C
N/C
Not connected
6
N/C
N/C
JTAG3
TDI (Test Data Input)
7
GND
Ground
JTAG4
TDO (Test Data Output)
8
+3.3V
3.3 V power
N/C
Not connected
9
N/C
Not connected
N/C
Not connected
10
3.3Vaux
3.3 V auxiliary power
+3.3V
3.3 V power
11
N/C
N/C
PERST#
Fundamental reset
Mechanical key
12
RSVD
Reserved
GND
Ground
13
GND
Ground
REFCLK+
Reference clock (differential pair)
14
PETp0
Transmitter differential pair, Lane 0
REFCLK
15
PETn0
GND
Ground
16
GND
Ground
PERp0
Receiver differential pair, Lane 0
17
PRSNT2#
Hot-Plug presence detect
PERn0
18
GND
Ground
GND
Ground
19
PETp1
Transmitter differential pair, Lane 1
RSVD
Reserved
20
PETn1
GND
Ground
21
GND
Ground
PERp1
Receiver differential pair, Lane 1
22
GND
Ground
PERn1
23
PETp2
Transmitter differential pair, Lane 2
GND
Ground
24
PETn2
GND
Ground
25
GND
Ground
PERp2
Receiver differential pair, Lane 2
26
GND
Ground
PERn2
27
PETp3
Transmitter differential pair, Lane 3
GND
Ground
28
PETn3
GND
Ground
29
GND
Ground
PERp3
Receiver differential pair, Lane 3
30
RSVD
Reserved
PERn3
31
PRSNT2#
Hot-Plug presence detect
GND
Ground
32
GND
Ground
RSVD
Reserved
Notes:
1. Optional signals that are not implemented are left as no connects on the board side connector.
2. Reserved signals are no connects on the board side connector.
3. Although support of CWAKE# is optional from the board side connector perspective, an allocated wire is mandated for the cable
assembly.

One Stop Systems
OSS-KIT-EXP-6002| 11
4. Board side pin-outs on both sides of the Link are identical. The cable assembly incorporates a null modem for the PCIe transmit and
receive pairs.
4.4 PCI Express x4 Connector PIN Assignment
4.5 Pin-out for the PCIe x4 Cable
Pin #
Cable Side 1
Cable Side 2
Pin #
A1 A4 A7 A10 A13 A16 B1
B4 B7 B10 B13
GND
Drain Wires
GND
A1 A4 A7 A10 A13 A16 B1
B4 B7 B10 B13
A2
PETp0
Differential Pair
PERp0
B2
A3
PETn0
PERn0
B3
A5
PETp1
Differential Pair
PERp1
B5
A6
PETn1
PERn1
B6
Pin #
Cable Side 1
Cable Side 2
Pin #
A8
PETp2
Differential Pair
PERp2
B8
A9
PETn2
PERn2
B9
A11
PETp3
Differential Pair
PERp3
B11
A12
PETn3
PERn3
B12
A14
CREFCLK+
Differential Pair
CREFCLK+
A14
A15
CREFCLK
CREFCLK-
A15
A17
SB_RTN
Hook-up Wire
SB_RTN
A17
A18
CPRSNT#
Hook-up Wire
CPRSNT#
A18
A19
CPWRON
Hook-up Wire
CPWRON
A19
B2
PERp0
Differential Pair
PETp0
A2
B3
PERn0
PETn0
A3
B5
PERp1
Differential Pair
PETp1
A5
B6
PERn1
PETn1
A6
B8
PERp2
Differential Pair
PETp2
A8
B9
PERn2
PETn2
A9
B11
PERp3
Differential Pair
PETp3
A11
B12
PERn3
PETn3
A12
B14
PWR
NC
PWR
B14
B15
PWR
NC
PWR
B15
B16
PWR_RTN
NC
PWR_RTN
B16
B17
PWR_RTN
NC
PWR_RTN
B17
B18
CWAKE#
Hook-up Wire
CWAKE#
B18
B19
CPERST#
Hook-up Wire
CPERST#
B19
Back shell
Chassis Ground
Overall Cable Braid
Chassis Ground
Back shell

One Stop Systems
OSS-KIT-EXP-6002| 12
4.6 Signal Descriptions
4.7 Connector Pin-outs for the PCIe x4 Cable Connector
PIN#
SIGNAL
DESCRIPTION
A1
GND
Ground reference
A2
PETp0
Differential PCI Express Transmitter Lane 0
A3
PETn0
A4
GND
Ground reference
A5
PETp1
Differential PCI Express Transmitter Lane 1
A6
PETn1
A7
GND
Ground reference
A8
PETp2
Differential PCI Express Transmitter Lane 2
A9
PETn2
A10
GND
Ground reference
A11
PETp3
Differential PCI Express Transmitter Lane 3
A12
PETn3
A13
GND
Ground reference
A14
CREFCLK+
Differential 100MHz cable reference clock
A15
CREFCLK-
A16
GND
Ground reference
A17
SB_RTN
Side Band Return
A18
CPRSNT#
Used for detection of external cable and if downstream system is powered
A19
CPWRON
Turns power on / off to slave type downstream subsystems
B1
GND
Ground reference
B2
PERp0
Differential PCI Express Receiver Lane 0
B3
PERn0
B4
GND
Ground reference
B5
PERp1
Differential PCI Express Receiver Lane 1
B6
PERn1
B7
GND
Ground reference
B8
PERp2
Differential PCI Express Receiver Lane 2
B9
PERn2
B10
GND
Ground reference
B11
PERp3
Differential PCI Express Receiver Lane 3
B12
PERn3
B13
GND
Ground reference
B14
PWR
+3.3V Cable Power
B15
PWR
B16
PWR_RTN
Cable Power Return
PETp(x)
PCI Express Transmit Positive signal of (x) pair.
PETn(x)
PCI Express Transmit Negative signal of (x) pair.
PERp(x)
PCI Express Receive Positive signal of (x) pair.
PERn(x)
PCI Express Receive Negative signal of (x) pair.
CREFCLK+/-
Cable REFerence CLocK: Provides a reference clock from the host system to the remote system.
SB_RTN
Side Band ReTurN: return path for single ended signals from remote systems.
CPRSNT#
Cable PReSeNT: Indicates the presence of a device beyond the cable.
PWR
PoWeR: Provides local power for in-cable redriver circuits. Only needed on long cables. Power does not go
across the cable.)
PWR_RTN
PoWeR ReTurN: Provides local power return path for PWR pins.
CWAKE#
Cable WAKE
CPERST#
Cable PCI Express Reset

One Stop Systems
OSS-KIT-EXP-6002| 13
B17
PWR_RTN
B18
CWAKE#
Power management signal for wakeup events (optional)
B18
CPERST#
Cable Reset#
4.8 PCI Express x4 Connector PIN Assignment
CFG(0:2)
BP PORT CFG
0
1
2
A0
A1
A2
A3
B0
0
0
0
X4
X4
X4
X4
X4
0
1
0
X8
0
X4
X4
X4
0
1
1
X8
0
X8
0
X4
1
X
X
X16
0
0
0
X4

One Stop Systems
OSS-KIT-EXP-6002| 14
5 Contacting Technical Support
Our support department can be by phone at 1 [phone]. Support is available Monday through Friday, 8:00 AM to 5:00 PM PT. When
contacting One Stop Systems Technical Support, please be sure to include the following information:
1) Name
2) Company Name
3) Phone Number
4) Fax Number
5) Email Address
6) Model Number
7) Serial Number
8) Computer Make
9) Computer Model
10) Operating System and Version
11) Make/Model of PCI cards in expansion chassis
12) Detailed description of the problem
You can also visit our web site at: HTwww.onestopsystems/support/T
For a quick response, use the Technical Support and RMA Request Form available in the Support Section of the website. Simply complete the
form with all required information. Please make sure that your problem description is sufficiently detailed to help us understand your problem.
For example: Don’t say “Won’t boot up.” Do say “Tried all the steps in the Troubleshooting Section and it still won’t boot up.”
For faster diagnosis of your problem, please run the two utility programs described in the following sections and include the diagnostic files
they generate with your email.
6 Returning Merchandise to One Stop Systems
If factory service is required, you must contact OSS Service Representative to obtain a Return Merchandise Authorization (RMA) number. Put
this number and your return address on the shipping label when you return the item(s) for service. One Stop Systems will return any product
that is not accompanied by an RMA number. Please note that One Stop Systems WILL NOT accept COD packages, so be sure to return the
product freight and duties-paid.
Ship the well-packaged product to the address below:
RMA # ________
One Stop Systems
2235 Enterprise Street, Suite#110 92029
USA
It is not required, though highly recommended, that you keep the packaging from the original shipment of your One Stop Systems product.
However, if you return a product to One Stop Systems for warranty repair/ replacement or take advantage of the 30-day money back
guarantee, you will need to package the product in a manner similar to the manner in which it was received from our plant. One Stop Systems
cannot be responsible for any physical damage to the product or component pieces of the product (such as the host or expansion interfaces for
the PCIe expansion chassis) that are damaged due to inadequate packing. Physical damage sustained in such a situation will be repaired at the
owner’s expense in accordance with Out of Warranty Procedures. Please, protect your investment, a bit more padding in a good box will go a
long way to insuring the device is returned to use in the same condition you shipped it in. Please call for an RMA number first.

One Stop Systems
OSS-KIT-EXP-6002| 15