Owon FDS315 User manual
FDS315
Fall Detection Sensor
Quick Sta Guide
2
Safety Handling
WARNING: Failure to follow these safety notices could result in re,
electric shock, other injuries, or damage to the Fall Detection Sensor
and other propey. Read all the safety notices below before using
the Fall Detection Sensor.
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or t to repair the unit on your own.
• Do not expose the unit or its accessories to ammable liquids, gases
or other explosives.
• Do not use harsh chemicals or strong detergents to clean it.
• Do not place it where infants and young children can touch, children
should use under parental supeision.
• Do not touch it when powering on to ensure your safety.
• Indoor use only.
3
Technical Specications
Wireless Connectivity
ZigBee • 2.4GHz IEEE 802.15.4
ZigBee Prole • ZigBee 3.0
RF Characteristics
• Operating frequency: 2.4GHz
• Internal PCB Antenna
• Range outdoor: 100m (Open
area)
Physical Specications
Operating Voltage • Micro-USB
Detector • 60GHz Radar
Detection Range • Occupancy: 4*6m
• Fall: 4*4m
Hanging height • 1.6~1.7m
Operating environment • Temperature: -10 ℃~+50 ℃
• Humidity: ≤ 90% non-condensing
Dimension • 86(L) x 86(W) x 37(H) mm
Mounting Type • Wall mount
4
Welcome
1
FDS315 Fall Detection Sensor can detect the presence, even if you are
asleep or in a stationa posture. It can also detect if the person falls,
so you can know the risk in time. It can be tremendously benecial in
nursing homes to monitor and link with other devices to make your
home smaer.
This guide will provide you with an oveiew of the product and help
you get through the initial setup to installation.
• ZigBee 3.0
• Discern presence, even if you are in a stationa posture
• Fall detection (only works on single player)
• Identify the location of human activity
• Out-of-bed detection
• Real-time breathing rate detection during sleep
• Extend the range and strengthen ZigBee network communication
• Suitable for both residential and commercial application
Features:
5
2Installaion
Impoant safety information!
• Do not touch the terminals of the device while testing.
• Turn o all the power supply for this equipment before installing.
• Make sure that the power supply is off before connecting or
disconnecting it to an auxilia device.
• Always use a properly rated voltage sensing device to confirm
power is o.
• Replace all devices, doors and covers before applying power to the
equipment.
Before installing, the location should be:
a) Avoid objects that generate high temperature, and keep a
distance of more than 1M from heating devices (bathroom, radiator,
etc.)
b) To avoid occlusion, the distance between the device and other
furniture such as cabinets on the same side is greater than 1M.
c) Avoid objects that will block the monitoring range.
d) Far away from pets, ventilation ducts, fire-fighting ducts,
drainage ducts, mechanical vibration, large metal equipment, or
places with vibrating and swinging objects.
e) More than 4m away from other radar equipment
6
Installation:
1) Install the back cover of the wall stand as below.
2) Align the wall stand with the wall sticker and screw them together
using gear.
Note: The arrow on the wall sticker need to point up.
7
4) Locate the hooks of the mounting bracket and line up the hooks with
the mounting holes on the sensor, then t the hooks into the mounting
holes as below picture.
3) Screw the mounting bracket into the wall stand.
8
7) Peel off the wall sticker and attach the sensor to the wall. Do
not install the sensor on the same wall side as the door. After the
installation is completed, please check whether it is rm and cannot
be shaken.
6) When using the sleep monitoring function, the sensor should be
installed on the wall at the head of the bed. So please nd a suitable
location when installing.
5) The recommended height for installing is 1.6M, which can be
adjusted according to the reality (adjustment range should not
exceed +/-10CM). And wall stickers are not suitable for sticking on
lime wall, brick, cement wall and wallpaper.
1.6m
9
8) Gently adjust the gear adjuster to feel the gear of the wall stand.
Adjust the gear of the wall stand to the rst gear (about 20 degrees)
and make sure the stand is open about 80mm. After that, tighten the
gear adjuster.
3Get to know your device
LED indicator
Micro-USB
8
0
mm
10
Reset Button
Reset: Press and hold the reset button for 10 seconds until the LED
light ashes red three times.
Reset Button
LED Color Status What it means
No light / No presence detected
Green
Always-on Presence detected
Flashing Device has not joined a ZigBee network
and is ready to join the gateway
Red Flashing Falling detected
LED indicator
The status gives the following information:
Note:
It will take about 10 minutes to let the sensor's status changes from
from occupied to unoccupied if you are out of the detect range.
11
4Congure Network
4.1 Before staing, you will need:
• A ZigBee Gateway.
4.2 Adding to the gateway's network:
Follow the steps below to join sensor to the gateway's network:
1. Power on the sensor through Micro-USB, the LED indicator will
sta ashing green, which means it is ready to join the network. If not,
please reset it.
2. Set your gateway to permit joining.
3. The sensor will join the gateway's network automatically and the LED
indicator stops ashing green when successfully joined.
Table of contents
Other Owon Accessories manuals
