Owon PIR313 User manual

PIR313 PIR Multi-Sensor
Quick Start Guide

2
The PIR313 Multi-sensor is used to detect movement, temperature &
humidity, illuminance in your property. It allows you to receive notification
from the mobile app when any movement is detected. You may also use the
multisensor to monitor temperature & humidity, as well as illuminance.
This guide will provide you with an overview of the product and help you
get through the initial setup.
Ambient luminance sensor
LED indicator
PIR sensor
Get to know your device
2
Introduction
1

3
Reset button
• Join network. Press the Reset button once,the indicator flashes red three
times indicating the sensor is ready to join a ZigBee network (if not, please
return the device to default factory setting)
• Reset. Press and hold the Reset button for ten seconds until the LED
indicator flashes three times to restore the smart plug to default factory
settings.
LED status What it means
Red LED flashing
three times
Device has not joined a network or is
ready to join a ZigBee network
Green LED flashing
three times Joined a ZigBee network
Red LED flashes once Motion detected
LED indicator
The LED status gives the following information:
Reset button
Dip-switch

4
3.1 To get started, you will need:
A Gateway
A mobile app
2 AA batteries
3.2 Multi-sensor setup
1. Switch the Dip-switch to a proper side. Power on the Multi-sensor.
Get started
3
Status
Dip switch ON OFF
1Disable notifications when
device is tampered.
Enable notifications when
device is tampered.
2Alarm will be shown in the
mobile app for 1 minutes.
Alarm will be shown in the
mobile app for 30 seconds.
3Reserved. Reserved.
4
Device function:
Temperature and humidity,
motion detector.
Device function:
Temperature and humidity,
motion detector, illuminance
detector.
Note: Changes made to the dip switch will became effective after you remove
and rejoin the sensor to your system.
Dip switch

5
3.4 Installation
You can mount the multi-sensor to the wall as a traditional motion sensor,
or you can choose to keep your multi-sensor on a bookshelf or table.
Wall mounting
Please peel off the liner on the double-sided tape and mount the sensor on
the surface of the wall.
1. Please ensure that the surface is clean and secure.
2. Install the Multi-sensor in places where intruders are most likely to enter.
3. Avoid mounting the Multi-sensor close to pets, air conditioners, heaters,
sunshine and places where the temperature varies.
3.3 Connect to the gateway’s network
1. Set your gateway to permit joining.
2. Press the reset button once and the LED indicator will flash red for three
times quickly indicating the sensor is ready to join the gateway (reset the
Multi-sensor if not).
3. The sensor will join the gateway automatically. The LED indicator will
flash green for three times when it has successfully joined. Please wait for
30 seconds for the device to sync its data.
4. Now you can see the multi sensor in the mobile App.

6
Avoid mounting
2.1m
1m 3m 6m
Mount example

7
Wireless connectivity • ZigBee 2.4GHz IEEE 802.15.4
ZigBee profile • Home Automation Profile
Range outdoor/indoor • 100m/30m
Operating Voltage • DC 3V (2*AA battery)
Current • Standby Current: ≤40μA
• Alarm Current: ≤110mA
Temperature Measurement • Range: -10~85° C
Humidity Measurement • Range: ≤80% RH
Illuminance Mesurement • Range: 0 ~128 klx
• Resolution: 0.1 lx
Operating Ambient
• Temperature: -10 ~ 55°C
• Humidity: maximum 85%RH
• (no congelation)
Installation Height • 2.1 m
Detecting • Distance: 6m
• Angle: 120°
Dimensions • 83(L) x 83(W) x 28(H) mm
Weight • 65g
4Technical Specifications

8
Safety Notice
5
WARNING: Failure to follow these safety notices could result in fire,
electric shock, other injuries, or damage to the multi sensor and other
property. Read all the safety notices below before using the multi-sensor.
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit on yourself.
• Do not expose the unit or its accessories to flammable liquids, gases or
other explosives.