Owon THS 317-ET User manual

1
ZigBee Multi-Sensor
Quick Start Guide

2
WARNING: Failure to follow these safety notices could
result in 󽗉re, electric shock, other injuries, or damage to
the ZigBee Multi-Sensor and other property. Read all the
safety notices below before using the ZigBee Multi-Sensor.
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet
light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit on your own.
• Do not expose the unit or its accessories to 󽗊ammable
liquids, gases or other explosives.
Safety Handling

3
Technical Speci󽗉cations
Wireless Connectivity
ZigBee • 2.4GHz IEEE 802.15.4
ZigBee Pro󽗉le • ZigBee 3.0
RF Characteristics
• Operating frequency: 2.4GHz
• Range outdoor/indoor: 100m
/ 30m (Open area)
• Internal PCB Antenna
Physical Speci󽗉cations
Battery • DC 3V (Two AAA batteries)
LED • 2-color LED (Red,Green)
Operating environment
• Temperature: -10℃ ~+55℃
• Humidity:
≤ 85% non-condensing

4
Detecting range(PIR)
• Distance: 5m
• Angle:
up/down 100°
left/right 120°
Dimensions
• 62(L) × 62 (W)× 15.5(H) mm
• Line length of remote probe:
External temperature: 2.5m
(Optinal)
Mounting Type • Tabletop stand or Wall
mounting

5
The Multi-sensor is used to measure the ambient temperature
& humidity with built-in sensor and external temperature
with remote probe. It is available to detect motion, vibration
and allows you to receive noti󽗉cations from mobile app. The
above functions can be customized, please use this guide
according to your customized functions.
This guide will provide you with an overview of the product
and help you get through the initial setup.
Welcome
1

6
Installation
You can mount the multi-sensor to the wall, ceiling or keep
your multi-sensor on a bookshelf or table.
• Please ensure that the surface is clean and secure.
• You can peel o󽗈 the tape on the back or lock it with screws.
• ZigBee 3.0
• PIR motion detection (Optional)
• Vibration detection (Optional)
• Environmental temperature & humidity measuring
(Optional)
• External temperature probe(Optional): Available for water
measurement
• Low power consumption
Features:
2
PIR/Vibration/Environmental temperature & humidity
function:

7
1. Avoid mounting the Multi-sensor close to pets, air
conditioners, heaters, sunshine or places where the
temperature varies.
2. You need to pay attention to the distance and range of the
sensor when installing.
2.1m
1m 3m 5m
100˚
120˚

8
External temperature probe:
Please refer to the mounting example below. You can
measure the temperature by touching the probe with the
measured object. Such as water, 󽗊oor, metal etc. But don't
put it in the environment with strong acid and alkali

9
Get to know your device
LED status What it means
Red LED 󽗊ashes once Motion detected
When you press the reset button once
Flashing green Device has joined a ZigBee
network.
Flashing red Device has not joined a ZigBee
network.
LED indicator
The LED status gives the following information:
LED indicator Reset button
3

10
Reset button
Reset: Press and hold the reset button for 10 seconds until
the LED light 󽗊ashes three times at third second, and it will
󽗊ash for three times again at tenth second.
4.1 To get started, you will need:
• A Zigbee Gateway.
• A mobile phone with a mobile APP installed.
4.2 Adding to the gateway's network
1. Set your gateway to permit joining (see your gateway's
manual).
2. Power on the Multi-sensor and press the reset button once
to make sure the LED indicator is 󽗊ashing red (If not, reset it
Con󽗉gure Network
4

11
to factory defaults).
3. Make sure the Multi-sensor is in the range of gateway's
network. After few seconds the Multi-sensor will join the
gateway automatically and the LED indicator will 󽗊ash green
when it successfully joined.
Note: If the adding is failed, simply reset the Multi-sensor
and retry.