Ozito 80 series User manual

80 SERIES
AIR STAPLER
12.8mm
INSTRUCTION MANUAL
SPECIFICATIONS
Min. Pressure: 70PSI
Max. Pressure: 120PSI
Magazine Capacity: 100 Staples
Staple Type: 12.8mm
Staple Length: 6-16mm
Air Inlet: 1/4” BSP
Weight: 0.85 kg
RST-80S
WHAT’S IN THE BOX
Air Stapler
Safety Goggles
Oil Pot
ozito.com.au
Hex Keys
200 Staples
Kit Box

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
8 Safety Goggles
9 Oil Pot
10 Hex Keys (3 and 4mm)
11 200x Staples
ACCESSORIES
1 Striker Pin
2 Trigger Lock-off
3 Trigger
4 Handle
5 Magazine Release
6 Magazine
7 Air Inlet Connector
AIR STAPLER
KNOW YOUR PRODUCT
1
8 9 10 11
2 3 4 5 6 7
1. CONNECTING AIR SUPPLY
SETUP & PREPARATION
1 Pullbackthesleeveonhosetting,insertmaleendand
releasesleeveonhosetting.
WARNING! ENSURE THE TOOL IS DISCONNECTED FROM
THE AIR SUPPLY BEFORE PERFORMING ANY OF THE
FOLLOWING OPERATIONS.
WARNING! ENSURE THAT THE COMPRESSOR PRESSURE
DOES NOT EXCEED 120PSI.

2. LOADING STAPLES 3. CONTROLS
1. Squeeze the magazine release and pull the magazine away from
the tool.
1. Torethestaplegunsimplysqueezethetrigger.
1. Topreventthestaplerfromring,rotatethetriggerlock-offsothat
it stops the trigger from being pressed.
Note: Thestaplerwillonlyreonceifthetriggerisheldup.The
triggermustbereleasedtoreasecondstaple.
3. Closethemagazine,ensuringitclicksintoplace.
2. Place a row of staples into the middle of the magazine so that the
staplestcumfortablyintheinnerchamber.
OPERATION
Trigger
Trigger Lock-off
NOTE: IF THE MAGAZINE WILL NOT CLOSE, THE
MAGAZINE MAY BE OVER CAPACITY. REMOVE SOME
STAPLES THEN TRY TO CLOSE AGAIN.

RST-80S
4. OPERATING THE STAPLE GUN 5. TROUBLESHOOTING
1. Place the staple gun against the work surface so that the
nosepiece of the tool is where you want the staple to be located.
1. Remove the two Hex screws from the front of the staple gun
using the 4mm supplied Hex key.
2. Remove the front plate held by the two screws.
3. Thejammedstapleshouldfallout.Ifnot,useapairofpliersto
securely grip and remove.
4. Reassemble by placing the plate back on and tightening the two
Hex screws.
2. Pushthetoolrmlydownontheworksurface.
3. Squeezethetriggertoreastaple.
Clearing Jammed Staples
WARNING! ENSURE THE TOOL IS DISCONNECTED FROM
THE AIR SUPPLY BEFORE PERFORMING ANY OF THE
FOLLOWING OPERATIONS.

MAINTENANCE
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
TROUBLESHOOTING
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recyclingpackagingreducestheneedforlandllandrawmaterials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
•Keeptheventilationventsofthestapleguncleanatalltimes,ifpossible,
prevent foreign matter from entering the vents.
•Iftheenclosureofthestaplegunrequirescleaning,donotusesolventsbut
a moist soft cloth only. Never let any liquid get inside the staple gun; never
immerse any part of the staple gun into a liquid.
•Oil after each use. This will reduce corrosion of the staple gun and ensure tool
longevity.
Staple gun does not re
Check that the trigger lock-off is not preventing the trigger from being pressed. If
thetriggerlock-offisoutofthewayandthegunstilldoesnotre,youmayhavea
jammed staple. Follow the instruction in this manual to remove the jam.
Ensuresufcientairpressure(within70-120PSI)
The magazine will not close
Themagazinecatchmaynotbeslidingoutoftheway,simplyholddownthe
magazine release lever and slide the magazine in. Ensure that the magazine is
secure.
The magazine chamber may be over capacity. Remove some nails/ staples then
try to close the magazine again.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
Warning Read instruction
manual
Wear eye protection
No load speed
Wear ear protection
Revolutions or recipro-
caton per minute
/min no

SPARE PARTS Tool:
Model No.
Item
No. Description Part No.
How To Order
Available spare parts can be ordered through the Special Orders Desk at any Bunnings Warehouse. If you have any
furtherquestions,pleasecontactOzitoCustomerServiceon:
Australia:1800069486
NewZealand:0508069486
[email protected]
The following is a list of spare parts carried by Ozito.
Please contact Customer Service for any parts not
listed.
Tool: 80 Series Air Stapler
Model No. RST-80S
Item
No. Description Part No.

• Always assume that the tool contains fasteners. Careless handling of the
staplercanresultinunexpectedringoffastenersandpersonalinjury.
• Do not point the tool towards yourself or anyone nearby. Unexpected
triggering will discharge the fastener causing an injury.
• Do not actuate the tool unless the tool is placed rmly against the
workpiece. Ifthetoolisnotincontactwiththeworkpiece,thefastenermaybe
deectedawayfromyourtarget.
• Disconnect the tool from the air supply when the fastener jams in the tool.
Whileremovingajammedfastener,thenailerorstaplermaybeaccidentally
activated if it is connected to the air supply.
• Do not use this stapler for fastening electrical cables. It is not designed
for electric cable installation and may damage the insulation of electric cables
therebycausingelectricshockorrehazards.
NAILER SAFETY WARNINGS
STAPLE/NAIL COMPATIBILITY
The RST-80S accepts staples with the below measurements
PLEASE NOTE: The RST-80S does not accept cable or
round “U” shaped nails. Only attempt to use staples with the
measurements outlined in this manual.
Note: All measurements are in mm.
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the
warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power
tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
d. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts.Looseclothes,jewelleryorlonghaircanbecaughtinmovingparts.
e. Check the maximum pressure rating of any tools or accessories that you intend using with the
compressor. The output pressure of the air from the compressor must be regulated so that it never exceeds
the rated pressure of the tool or accessory.
f. Always wear safety goggles or glasses when using the air tools. Never point the nozzle of an accessory
towards any part of your body or towards another person.
g. Drain the moisture from the tank daily. It will help prevent corrosion.
h. The tool must be used only for its prescribed purpose. Any use other than those mentioned in this Manual
will be considered a case of misuse. The user and not the manufacturer shall be liable for any damage or
injury resulting from such cases of misuse.
WARNING! Intheeventthatanairlineiscutorbroken,theairsupplymustbeturnedoffatthe
compressor. A broken air line which is not supported is extremely dangerous and can whip around
veryquickly,bothwiththecapabilityofstrikingpeople,andblowingforeignparticlesintotheair.
• Do not attempt to catch the air line but immediately keep bystanders well clear and turn off the air supply to
thehose,turnoffthecompressorattheOn/Offbutton,andthenremovethehosefromthecompressor.
• Thisapplianceisnotintendedforusebypersons(includingchildren)withreducedphysical,sensoryor
mentalcapabilities,orlackofexperienceandknowledge,unlesstheyhavebeengiventhesupervisionor
instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
GENERAL AIR TOOL SAFETY WARNINGS
0.95
12.8
6-16
0.65

IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase and is intended for DIY (Do It
Yourself) use only. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
0414