paasche H Series User manual

INSTRUCTIONS AND PARTS LIST HS AIRBRUSH 9/06/2019
HS Model Airbrush
Single Action–External Mix–Siphon Feed
Added Bottle Connection
Instruction Manual & Replacment Parts
OPERATING INSTRUCTIONS:
Approximate Working Pressures:
• 20lbs.orLess:Stippleandgranulatede󰀨ects,pressurewillvarywithviscosityofuid.
• 20to30lbs.:Mediumconsistencywatercolors,inks&dyes.
• 30 lbs. or More:Heavyuids,acrylics,reducedlacquers,varnishes,paintsorceramicglaze.
Sizes:
• HS-1(.45mm)HeadandHC-1-3Aircapforlightuids.
• HS-3(.64mm)HeadandHC-1-3Aircapformediumuids.
• HS-5(1.06mm)HeadandHC-5Aircapforheavieruids.
1.Attachhosetoairsupplyandallowairtoblowafewseconds.Shuto󰀨beforeattachingtoAirbrush.Thisprocedurewill
removedirtfromairlineandhose.
Caution: Hold rmly and point away from face.
2.Attachhosecouplingtotheairbrush.
3.AttachColorCuporBottleto HNS-1-3, or 5 Needle by exerting a rm twisting motion to t tapered tube securely into
taperedNeedleinlet.Thenwrenchtightenlockingnut.
4.FillColorCuporBottle1/2to3/4full.Useeyedropperorbrushforaddingsmallamountsofcolortometalcolorcup.When
usingColorBottle,ventholemustbekeptopen.
5.ToSpray,holdAirbrushlikeapencilcomfortablybetweenthumbandforengerusingmiddlengerasaguideandsupport.
Likewriting,holdforengereasilyonH-155FingerButtonandPresstoopenairvalve.
6.Regulatevolumeofcolorandsizeofspraybyrotating HT-1,3or5Tipclockwisetoincreaseandcounterclockwiseto
decreaseowofcolor.
7.StippleAdjustment:  Reducing the airlinepressureis the easiest method usedwhencreatinga stippled e󰀨ect with the
airbrush.Pressurecanbereducedbyusinganyofthefollowingitems:3ANeedleValveinstalledontheH-128AValve
CasingoftheAirbrushorbyusingtheR-75AirRegulatorandreducingthepressure.
8.Toadjustforheavieruids,turntipwideopen,loosensetscrew,slideneedlebacktoobtainbetterow.
CARE AND CLEANING:
1.Pouranyremainingcolorbackintoitsoriginalcontainer.
2.WipeColorCuporBottleclean,usingclothmoistenedwithpropersolvent.
3.HoldAirbrushatadownwardangleandputafewdropsofsolventthroughColorAdjustingPartAssembly.Toushout
theremainingcolorintheHSColorAdjustingPartAssembly,applypressuretothe H-155FingerButton.
4.ApplyatinydabofVaselinetotheHColorAdjustingPartandHC-Aircapthreadseverytwoorthreemonthstopreventcolor
buildupandconsequentfreezingoftheColorAdjustingPartAssemblyandAircap.
HOW TO OPEN CLOGGED FLUID PASSAGES:
1.AgitatecolorinBottleAssemblybyplacingngermomentarilyoverHC-AircapwhileairispassingthroughtheAirbrush.
Thiswillblowcolorbackintobottlethusopeningcloggeduidpassages.Do not do this with a cup as color may blow
out of cup.
2.ShouldHS-1,3or5ColorAdjustingPartAssemblybecomeclogged,loosenH-153SetScrew,unscrewHT-1,3or5Tip
fromHNNeedle,gentlypullbackthroughball-shapedsupportandremoveTip.
3.CleanPartscarefully,usingnothingharderthanawoodentoothpick.
4.Toreassemble,reversethisprocedure,makingsuretheshoulderoftheNeedleseatsupagainstball-shapedsupport.
5.Iftheneedleandtiparecompletelyclogged,soakinaclosedbottleofpropersolventuntilclean.
INTRODUCTION:
Paasche® model HS Airbrush features machined Brass Body and Nickel
SilverColorPart,simplicityofdesignandeaseinoperation.Theairandcolor
feeds are independent and adjustable to give a xed line, shade or stipple
e󰀨ect.
For Multi-Language Manuals Go To: www.paascheairbrush.com

HS - AIRBRUSH MODEL REPLACEMENT PARTS
# Part No. Description
1. HC-1-3,5  Aircapw/O-ring(SelectSize)
2. 3A-4   “O”Ring(Packof6)
3. HS-1,3,5  ColorAdjustingPart(SelectSize)
4. HT-1,3,5  Tip(SelectSize)
5. H-185   Packing
6. H-184   PackingNut
7. HNS-1-3,5 Needle(SelectSize)
8. H-153   SetScrew
9. H-150N  Shell(IncludesH-128A)
10. H-155   FingerButton
11. H-143   Handle(Nylon)
12. HVL-200 Metal Handle (Aluminum - optional)
14. H-128A  ValveCasing
15. H-192A  ValvePlungerw/A-53
16. A-53   ValveWasher(Packof6)
17.A-22   ValveSpring
18.A-23R  AirValveNut
19. F-186   Wrench
20. A-34 Hanger
HS - Old Style Replacement Parts
22. H-175A AirValveAssembly
23. A-23R AirValveNut
24. A-22  ValveSpring
25. H-21A ValvePlunger
26. A-52  ValveWasher(Packof6)
 27. H-128A ValveCasing
28. A-143  NeedleGuideSpring
29. H-156 Stipple Adjuster
30. H-157  FingerLeverAssembly
Old Style Replacement Parts
H-1/4-OZ
(1/4oz Metal)
HS-3-OZ
(3oz Glass)
HS-1-OZ
(1oz Glass)
HPS-3-OZ
(3oz Plastic)
HS-2-OZ
(2oz Metal)
A-1/8-4, 6, 8. 10, 15, 20, 25 or 50
Braided Air Hose with couplings (Select Length)
(3A-4 O-ring for airbrush coupling)
WARNING: Spraymaterialsmaybeharmfulifinhaled
orallowedtocomeintocontactwiththeskinoreyes.
Consult the product label and Material Safety Data
Sheetsuppliedforthespraymaterial.Followallsafety
precautions.CAUTION:WellVentilatedAreaRequired
to remove fumes, dust or overspray. Maximum Air
Pressure 75 P.S.I.
HPS-8-OZ
(8oz Plastic)
PaascheAirbushCo.
951158thPlaceKenosha,WI53144
Phone:[phone]Email:[email protected]
Website:Paascheairbrush.com
For Multi-Language Manuals Go To: www.paascheairbrush.com