Pacific Casual 5LGZ0702V2NN User manual

5LGZ0702V2NN
Pavilion Hexagon Roof Style Gazebo with Top Finial, 13' Diagonal
ASSEMBLY INSTRUCTIONS
Questions, problems, missing parts? Before returning to the store,
rvice
7.30 a.m. - 4.30 p.m., PST, Monday - Friday
888-445-7757
[email protected]
Model #
（Netting sold Seperately)

Page 2

A 6
B 6
C 6
D 6
E 6
F 6
12
G
H 1
I 1
J6
M6×35
K 42
M6×16
M 1
N 12
L
Q
1
6
O
6
P
Ref # Illustration / Description Qty
PART LIST
Corner Post
Post Base
Cross Beam
Long Corner Rib
Short Corner Rib
Bracket
Cast Accent
Vent Hub
Finial
Bolt,Nut and Bolt Cap
Bolt and Bolt Cap
Wrench
Ground Stake
Anchor
Guy Rope
Canopy
Page 3
Screw 18
R
S
Plastic clip
Plug
48
12
M5×10
Please have a Philips screwdriver, a hammer and a ladder ready before you start
to erect the garden house.

Page 4
K
F
A
L
Step 1: Attaching Post Bases and Brackets to Corner Posts
1. Attach one Post Base (B) to the bottom of Corner Post (A) with three screws (L)
2.Attach one Bracket (F) to the top of Corner Post (A) with one Bolt and Cap (K) using
hex wrench (M).
3. Repeat the above procedures for the other five Corner Posts (A).
using a Philips screwdriver.
B
A
L 18
K 6
B
F
M 1
M6×16
M5×10
6
6
6

1. Feed eight plastic clips (O) into each netting rail on the cr
C
K
Step 2: Setting up the Main Frame
2. Attach two Corner Posts (A) to both ends of Cross Beam (C) with four Bolts and Bolt
Caps (K) using Hex Wrench (M).
3.Repeat this until the whole main frame is up.
Page 5
C 6
K 24
M6×16
M 1
48O
12P
oss beam (C) .
Hammer one plug (P) into each end of each nettting rail.
O
8pcs
P
C

Step 3: Attaching the Cast Accents
G 12
KM6×16 12
G
K
M1
1. At each Corner Post (A) attach two Cast Accents (G) to each adjacent Cross Beams (C)
with two Bolts and Bolt Caps (K) using Hex Wrench (M).
2. Repeat this until all Cast Accents (G) are attached to Cross Beams (C) and Corner
Posts (A).
Page 6
IMPORTANT: DO NOT FULLY TIGHTEN ALL BOLTS (K) IN STEP 2
UNTIL CAST ACCENTS (G) ARE ASSEMBLED IN STEP 3.
IMPORTANT: PLEASE LOOSEN BOLTS (K) IF CAST ACCENTS (G)
CANNOT BE PROPERLY ALIGNED TO CROSS BEAMS (C).

Step 4: Assembling the Roof Frame
D
E
D
DD
D
D
E
E
E
E
E
D
E
6
6
H
H 1
1. Snap one Short Corner Rib (E) into each Long Corner Rib (D).
2. Snap the assembled corner rib into one recevier of Vent Hub (H).
3. Repeat this for the remaining assembled corner ribs.
Page 7

Step 5: Attaching the Roof Frame onto the Main Frame
M6×30
J6
1
J
1. With a ladder at the center of the main frame, place the roof frame over the main frame.
2. Align assembled corner ribs to Brackets (F). Attach each corner rib to each bracket with
one Bolt, Nut and Bolt Cap (J) using wrenches (M).
3. Repeat the above procedure until all corners ribs are secured.
F
Page 8
M
Please ensure all bolts (J, K & L ) are completely tightened once all parts have been
attached to frame.

Step 6: Attaching the Canopy and the Finial
I
S
I 1
S1
1. Place the Canopy (S) over the roof frame.
2. Pull each corner of the Canopy (S) to the Short Corner Rib (E) until the end of each
Corner Rib (E) fits well into the pockets at each corner of the Canopy (S) leaving one
corner open for the next step.
3. Using the ladder, screw the Finial (I) onto the top of the Vent Hub (H) through
the grommet at the center of the Canopy (S).
Page 9

Step 7: Anchoring the Garden House
N
R
Q
12
R
N
Q 6
6
7
1. Adjust the position of the garden house, making sure all Corner Posts are completely upright.
2.
Measure out from the Corner Posts to the longest possible distance (best to use the length
and secure Guy Rope (R) to ground at 45 degrees with
of the Guy Rope (R))
Hammer two Groud Stakes (N) through each Post Base (B) into soft ground.
A
Plastic Stakes (Q).
Page 10
5LGZ0702V2NN
7757
B