Pacific Casual Sarasota 217-H40-4DS User manual

USE AND CARE GUIDE
Sarasota 4pc Cushioned Deep Seating Set
Questions, problems, missing parts? Before returning to the store,
Model #217-H40-4DS
call Our Customer Service
7.30 a.m. - 4.30 p.m. PST, Monday - Friday,
888-445-6690
[email protected]
Ver: 2-24-2021

2
Table of Contents
Care & Cleaning
Before using, wipe with a clean, dry cloth. Do not use bleach or solvents. Treat frame with one step liquid wax for maximum protection against
UV light and salty, damp air. When not in use, store furniture in a cool, dry place. If your set includes cushions, they may be cleaned by hand
with a mild solution of soap and water. Rinse cushion thoroughly and allow to drip dry. Do not machine wash or tumble dry, as cushions
may shrink. Do not use bleach or solvents on fabrics.
When cleaning the tabletop make sure to use a soft, clean cloth that doesn’t
bleed color as well.
Table of Contents .......................................................2
Important Safety Instructions ............................................2
Pre-Assembly....................................................................3
Planning Assembly ................................................................3
Hardware Included.................................................................. 3
Package Contents .................................................................. 4
Assembly..... ....................................................................5
................................................................ 2
Care & Cleaning ..
.... .
....
..
Important Safety Instructions
IMPORTANT: Please check the tightness of the bolts
periodically.
CAUTION: Use the table and chairs on flat ground only.
READ ALL INSTRUCTIONS BEFORE USE
SAVE THESE INSTRUCTIONS
When using a furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this furnishing.
To reduce the risk of injury to persons:
a) Close supervision is necessary when this furnishing is used by or near children, or disabled persons, if applicable.
b) Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

3
Pre-Assembly
PLANNING ASSEMBLY
It will take two people about 30 minutes to complete the assembly process.
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Part Description Quantity
AA 16
FF Bolt (M6x15)
DD 16
Bolt cap (M6)
AA FF
DD
Lounge Chairs
16
Part Description Quantity
AA 16
BB Bolt (M6x32) 16
16
DD
Bolt cap (M6)
Hex wrench 1 EE
Coffee Table
Love Seat
Part Description Quantity
AA 9
BB Bolt (M6x32) 8
9
DD
Bolt cap (M6)
GG
1
GG Bolt (M6x45)
AA BB DD EE
AA BB DD
Washer (M6)
Washer (M6)
Washer (M6)

Coffee Table A2
Part Description Quantity
A2 Table top
1B2
B2
Table leg 4
C2
Leg connector bracket 1C2
2
D
Pre-Assembly (continued)
PACKAGE CONTENTS
Lounge Chairs
A1
C
Part Description Quantity
A
Back panel 2
BSeat panel 2
Right armrest 2
C
DLeft armrest 2
B
1 Back cushion 2
2Seat cushion 2
Love Seat
D1
Part Description Quantity
A1 Back panel 1 A1
B1
Seat panel 1
C1
Right armrest 1
D1Left armrest 1
3
Back cushion 2
4Seat cushion 2
C1
4
3
4
B1

5
C
EE
BB BB
DD DD
EE
BB
DD
D
AA
AA
1
IMPORTANT:
When making alignment, the front part of the seat panel
shall be on the same line with the front leg.
NOTE:
Place the back panel (A) with the curve facing outward
from the chair frame.
EE
AB
BB BB
DD DD
BB
EE
BB
DD
DD
BB
DD
□Place the right armrest (C) on its side on a at, smooth surface. Align the seat panel (B) and back panel (A) to the armrest (C).
Secure the seat panel and back panel to the armrest (C) with washers(DD) and bolts (BB)
using the hex wrench (EE).
□Repeat the above procedure to attach the left armrest (D).
□Fully tighten all bolts (BB) once all bolts are in place. Cover all the bolts with bolt caps (AA).
Assembly (Lounge Chairs)

AA
AA
AAsssseemmbbllyy (Love Seat)
2□Place the back panel (A1) on its back on a flat, smooth surface.
□Attach armrests (C1) and (D1) to the back panel with washers (DD) and bolts (BB) using wrench (EE).
Do not fully tighten bolts until the end of Step 3.
□Note the curve of back panel (A1) shall face outward from the chair frame.
D1
A1
DD
DD
BB
BB
EE
C1
□Attach the seat panel (B1) to armrests (C1) and (D1) with washers (DD) and bolts (BB).
□Lock the seat panel and the back panel with washers (DD) and bolt (GG).
□Fully tighten all the bolts using hex wrench (EE).
EE
GG
DD
BB
DD
B1
DD
BB
B1
EE
A1
6
□Cover all the bolts with bolt caps (AA) . Turn the loveseat upright.

AAsssseemmbbllyy (Coffee table)
3
7
□Turn the table upright.
5
B2
A2
AA
FF
DD
4
DD
FF AA
□Place the table top (A2) upside down on a at, smooth
surface.
□Align the table legs (B2) to the table top.
□Attach table legs to the table top with washers (DD) and
bolts (FF) using the hex wrench (EE) .
□Do not fully tighten bolts until the end of Step 4.
□Align leg connector bracket (C2) to the four table legs (B2).
□Attach the leg connector bracket (C2) to table legs (B2) with
washers (CC) and bolts (BB).
□Once all bolts (AA) and (BB) are in place. Fully tighten all
the bolts using hex wrench (EE).
□Cover all the bolts with bolt caps (DD).
B2
C2

6Placing cushions
3
1
2
□Place cushions (1,2,3 and 4) on the lounge chairs and love seat.
□Level the chairs with foot glides if necessary.
AssemblyAssembly
8
4