Panasonic AFPX-C30R User manual

User's Manual
PROGRAMMABLE CONTROLLER
FP-X
ARCT1F409E-9
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Safety Precautions
Observe the following notices to ensure personal safety or to prevent accidents.
To ensure that you use this product correctly, read this User’s Manual thoroughly before use.
Make sure that you fully understand the product and information on safety.
This manual uses two safety flags to indicate different levels of danger.
WARNING
If critical situations that could lead to user’s death or serious injury is assumed by
mishandling of the product.
-Always take precautions to ensure the overall safety of your system, so that the whole
system remains safe in the event of failure of this product or other external factor.
-Do not use this product in areas with inflammable gas. It could lead to an explosion.
-Exposing this product to excessive heat or open flames could cause damage to the lithium
battery or other electronic parts.
-Battery may explode if mistreated. Do not recharge, disassemble or dispose of fire.
CAUTION
If critical situations that could lead to user’s injury or only property damage is
assumed by mishandling of the product.
-To prevent excessive exothermic heat or smoke generation, use this product at the values
less than the maximum of the characteristics and performance that are assured in these
specifications.
-Do not dismantle or remodel the product. It could cause excessive exothermic heat or smoke
generation.
-Do not touch the terminal while turning on electricity. It could lead to an electric shock.
-Use the external devices to function the emergency stop and interlock circuit.
-Connect the wires or connectors securely.
The loose connection could cause excessive exothermic heat or smoke generation.
-Ground the protective earth (PE) terminal (Class D grounding). Failure to do so could lead to
an electric shock.
-Do not allow foreign matters such as liquid, flammable materials, metals to go into the inside
of the product. It could cause excessive exothermic heat or smoke generation.
-Do not undertake construction (such as connection and disconnection) while the power
supply is on. It could lead to an electric shock.
Copyright / Trademarks
-This manual and its contents are copyrighted.
-You may not copy this manual, in whole or part, without written consent of Panasonic Electric
Works SUNX Co., Ltd.
-Windows is a registered trademark of Microsoft Corporation in the United States and other
countries.
-Ethernet is a registered trademark of Fuji Xerox Co., Ltd. and Xerox Corp.
-All other company names and product names are trademarks or registered trademarks of
their respective owners.
PLC_FPX
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Table of Contents
Before You Start
Differences in Functions Between Versions of Controller
Restriction on using the Add-on cassette
Programming Tool Restrictions
1. Features, Functions and Restrictions................................................... 1-1
1.1 Features and Functions of the Unit............................................................................1-2
1.2 Unit Types ...................................................................................................................1-6
1.3 Restrictions on Unit Combinations..........................................................................1-10
1.4 Programming Tools..................................................................................................1-14
2. Specifications and Functions of Control Unit...................................... 2-1
2.1 Parts and Functions....................................................................................................2-2
2.2 Power Supply Specifications......................................................................................2-5
2.3 Input Specifications....................................................................................................2-6
2.4 Output Specifications.................................................................................................2-8
2.5 Limitations on Number of Simultaneous Input/Output On Points..........................2-11
2.6 Terminal Layout ........................................................................................................2-20
3. Expansion Cassette and Expansion FP0 Adapter Specifications...... 3-1
3.1 Expansion Method......................................................................................................3-2
3.2 FP-X Expansion Unit...................................................................................................3-3
3.3 FP-X Expansion FP0 Adapter ...................................................................................3-11
4. I/O Allocation........................................................................................... 4-1
4.1 I/O Allocation...............................................................................................................4-2
4.2 Allocation of FP-X Control Unit..................................................................................4-3
4.3 FP0 Expansion Unit Allocation...................................................................................4-3
4.4 Allocation of FP0 Expansion Unit ..............................................................................4-4
4.5 I/O Allocation of FP-X Add-on Cassette.....................................................................4-6
5. Installation and Wiring ........................................................................... 5-1
5.1 Installation...................................................................................................................5-2
5.2 Installation Using Expansion Cable...........................................................................5-5
5.3 Expansion Method of FP0 Expansion Unit................................................................5-8
5.4 How to Install Add-on Cassette..................................................................................5-9
5.5 Power Supply............................................................................................................5-11
5.6 Wiring of Input and Output.......................................................................................5-17
5.7 Wiring of Terminal Block..........................................................................................5-20
5.8 Wiring of Add-on Cassette Terminal Block..............................................................5-22
5.9 Handling of Backup Battery......................................................................................5-25
5.10 Safety Measures......................................................................................................5-29
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

6. Tool Port and USB Port..........................................................................6-1
6.1 Tool Port and USB Port ..............................................................................................6-2
6.2 Functions of Tool Port................................................................................................6-3
6.3 USB Port......................................................................................................................6-6
7. Communication Cassette.......................................................................7-1
7.1 Functions and Types..................................................................................................7-2
7.2 Communication Specifications................................................................................7-16
7.3 Communication Function 1: Computer Link............................................................7-20
7.4 Communication Function 2: General-purpose Serial Communication...................7-36
7.5 Communication Function 3: PC(PLC) Link..............................................................7-56
7.6 Communication Function 4: MODBUS RTU Communication .................................7-75
7.7 Ethernet Communication (AFPX-COM5)..................................................................7-81
8. Application Cassette...............................................................................8-1
8.1 Expansion of Application Cassette............................................................................8-2
8.2 Application Cassettes.................................................................................................8-3
8.3 Specifications .............................................................................................................8-5
9. High-speed Counter, Pulse Output and PWM Output Functions (For Tr
Type) ............................................................................................................9-1
9.1 Overview of Each Functions.......................................................................................9-2
9.3 High-speed Counter Function..................................................................................9-11
9.4 Pulse Output Function..............................................................................................9-19
9.5 PWM Output Function (Pulse I/O Cassette).............................................................9-51
10. High-speed counter, Pulse Output and PWM Output functions (For Ry
Type) ..........................................................................................................10-1
10.1 Overview of Each Functions...................................................................................10-2
10.3 High-speed Counter Function ................................................................................10-9
10.4 Pulse Output Function (Pulse I/O Cassette)........................................................10-20
10.5 PWM Output Function (Pulse I/O Cassette).........................................................10-51
11. Security Functions..............................................................................11-1
11.1 Type of Security Functions.....................................................................................11-2
11.2 Password Protect Function....................................................................................11-3
11.3 Upload Protection...................................................................................................11-7
11.4 Setting Function for FP Memory Loader................................................................11-9
11.5 Table of Security Settings/Cancel........................................................................11-13
12. Other Functions ..................................................................................12-1
12.1 Transfer Function between Memories....................................................................12-2
12.2 Function of Master Memory Cassette ....................................................................12-3
12.3 P13 (ICWT) Instruction............................................................................................12-8
12.4 Analog Potentiometer.............................................................................................12-9
12.5 Sampling Trace Function......................................................................................12-10
12.6 Time Constant Processing...................................................................................12-13
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

13. Self-Diagnostic and Troubleshooting ............................................... 13-1
13.1 Self-Diagnostic function.........................................................................................13-2
13.2 Troubleshooting......................................................................................................13-4
14. Precautions During Programming..................................................... 14-1
14.1 Use of Duplicated Output .......................................................................................14-2
14.2 Handling BCD Data .................................................................................................14-4
14.3 Handling Index Registers .......................................................................................14-5
14.4 Operation Errors .....................................................................................................14-7
14.5 Instruction of Leading Edge Detection Method.....................................................14-9
14.6 Precautions for Programming..............................................................................14-13
14.7 Rewrite Function During RUN ..............................................................................14-14
14.8 Processing During Forced Input and Output.......................................................14-19
15. Specifications...................................................................................... 15-1
15.1 Table of Specifications ...........................................................................................15-2
15.2 Table of I/O Number Allocation ............................................................................15-13
15.3 Relays, Memory Areas and Constants.................................................................15-16
16. Dimensions ......................................................................................... 16-1
16.1 Dimensions .............................................................................................................16-2
16.2 Cable/Adapter Specifications.................................................................................16-4
17. Appendix ............................................................................................. 17-1
17.1 System Registers / Special Internal Relays / Special Data Registers...................17-2
17.2 Table of Basic Instructions...................................................................................17-48
17.3 Table of High-level Instructions ...........................................................................17-56
17.4 Table of Error codes .............................................................................................17-76
17.5 MEWTOCOL-COM Communication Commands..................................................17-89
17.6 Hexadecimal/Binary/BCD......................................................................................17-90
17.7 ASCII Codes ..........................................................................................................17-91
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Before You Start
Operating environment (Use the unit within the range of the general specifications when installing)
*Ambient temperatures:0 ~ +55 ℃
*Ambient humidity: 10% to 95% RH (at 25°C, non-condensing)
*Keep the height below 2000m.
*For use in pollution Degree 2 environment.
*Do not use it in the following environments.
- Direct sunlight
- Sudden temperature changes causing condensation.
- Inflammable or corrosive gas.
- Excessive airborne dust, metal particles or saline matter.
- Benzine, paint thinner, alcohol or other organic solvents or strong alkaline solutions such as ammonia
or caustic soda.
- Direct vibration, shock or direct drop of water.
- Influence from power transmission lines, high voltage equipment, power cables, power equipment,
radio transmitters, or any other equipment that would generate high switching surges.
(Min.100mm or less）
Static electricity
-Before touching the unit, always touch a grounded piece of metal in order to discharge static electricity.
-In dry locations, excessive static electricity can cause problems.
Wiring the Power Supply to the Control Unit
- Use a power supply wire that is thicker than 2 mm2 (AWG14), and twist it.
- The unit has sufficient noise immunity against the noise generated on the power line.
However, it is recommended to take measures for reducing noise such as using a isolating transformer
before supplying the power.
- Allocate an independent wiring for each power supplying line, input/output device and operating device.
- If using a power supply without a protective circuit, power should be supplied through a protective
element such as a fuse.
- Be sure to supply power to a control and an expansion units from a single power supply.
Turning on/off of the power of all the units must be conducted simultaneously.
Power supply sequence
In order to protect the power supply sequence, make sure to turn off the control unit before the
input/output power supply. If the input/output power supply is turned off before the control unit, or if the
control unit is not shut off momentarily, the controller detects change of input level, and might conduct an
unexpected operation.
Before turning on the power
When turning on the power for the first time, be sure to take the precautions given below.
• When performing installation, check to make sure that there are no scraps of wiring, particularly
conductive fragments, adhering to the unit.
• Verify that the power supply wiring, I/O wiring, and power supply voltage are all correct.
• Sufficiently tighten the installation screws and terminal screws.
• Set the mode selector to PROG. Mode.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Before entering a program
Be sure to perform a program clear operation before entering a program.
Operation procedure when using FPWIN GR Ver.2
Select “Online Edit Mode” on the FPWIN GR “On line” menu.
Select “Clear Program” on the “Edit” menu.
When the confirmation dialog box is displayed, click on “Yes” to clear the program.
Request concerning program storage
To prevent the accidental loss of programs, the user should consider the following measures.
• Drafting of documents
To avoid accidentally losing programs, destroying files, or overwriting the contents of a file, documents
should be printed out and then saved.
• Specifying the password carefully
The password setting is designed to avoid programs being accidentally overwritten. If the password is
forgotten, however, it will be impossible to overwrite the program even if you want to. Also, if a
password is forcibly bypassed, the program is deleted. When specifying the password, note it in the
specifications manual or in another safe location in case it is forgotten at some point.
• Upload protection
When the upload protection setting is specified, programs will be disabled to be read out. If the setting
is cancelled forcibly, all programs and system registers will be deleted. Therefore, note that programs
and system registers should be managed on your own responsibility.
Backup battery
Do not install the battery when it is not used.
There is a possibility of leak if the battery remains discharged.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Differences in Functions Between Versions of Controller
Version
Usable model
Usable functions
V1.10 Ry type -
UP/DOWN switching of high-speed counter by SYS instruction
Real number basic compare instructions 18 types
STF=S1, S2 ANF=S1, S2 ORF=S1, S2
STF<>S1, S2 ANF<>S1, S2 ORF<>S1, S2
STF>S1, S2 ANF>S1, S2 ORF>S1, S2
STF>=S1, S2 ANF>=S1, S2 ORF>=S1, S2
STF<S1, S2 ANF<S1, S2 ORF<S1, S2
STF<=S1, S2 ANF<=S1, S2 ORF<=S1, S2
V1.20
System register 36 for setting expansion unit recognition time
Ry type -
MEWTOCOL master function
F145(SEND) Data send
F146(RECV) Data receive
V2.00
E356(EZPID) Easy PID instruction
Ry type Tr type
Time constant processing of input (Refer to Chapter 12.6.)
CPU input: System register setting
Other input: F182(FILTR) Time constant processing
Sampling trace function (Refer to Chapter 12.5.)
Sampling by instructions
F155(SMPL) Sampling
F156(STRG) Sampling trigger
Sampling by specifying time
Leading contact, trailing contact instructions
ST↑ AN↑ OR↑
ST↓ AN↓ OR↓
An arbitrary device can be specified for the setting value of
Timer/counter instruction.
e.g.) TML 0, DT0
Other additional convenient instructions
F252(ACHK) ASCII data check
F284(RAMP) Inclination output
Baud rate setting (300, 600, 1200 bps) by SYS instruction
High-speed operation
F0(MV) and F1(DMV) instructions Execution time: Approx. 1us
Only when every operands are without index modifier.
Note) The Ry and Tr types with the same specifications have the same version name
Function addition to existing instructions
F70(BCC) Block check code calculation
F356(EZPID) Easy PID instruction
Reference: <Programming Manual ARCT1F313E>
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Restriction on using the Add-on cassette
Application cassettes that the version of the FP-X control unit is specified
FP-X Application cassette
Version of control unit
FP-X Analog output cassette
AFPX-DA2
Ver. 2.40 or later
FP-X Analog I/O cassette
AFPX-A21
FP-X Thermocouple cassette
AFPX-TC2
FP-X RTD cassette
AFPX-RTD2
Application cassettes that have restrictions when more than one units are used simultaneously
Current output range
FP-X Application cassette
Quantity
used
Control unit
C14
C30
C60
AFPX-DA2
1
○
○
○
2
－
△
Note1)
△
Note1)
AFPX-A21
1
○
○
○
2
－
○
○
AFPX-DA2 + AFPX-A21
Each 1
－
△
Note1)
△
Note1)
AFPX-DA2 + AFPX-COM5
Each 1
×
Note2)
×
Note2)
×
Note2)
AFPX-A21 + AFPX-COM5
Each 1
×
Note2)
×
Note2)
×
Note2)
AFPX-A21 + AFPX-DA2 + AFPX-COM5
Each 1
－
×
Note2)
×
Note2)
AFPX-DA2 1unit + AFPX-COM5 1unit
-
×
Note2)
×
Note2)
AFPX-A21 2units + AFPX-COM5 1unit
-
×
Note2)
×
Note2)
Note1) Up to 2 channels can be used for the current output range.
(When using two units, it is possible to use the 2-ch current output range and 2-ch voltage output range.)
Note2) The AFPX-DA2 and AFPX-A21 both cannot be used with the AFP-COM5 (Ethernet).
Voltage output range (When using with the output current of 1 mA or below)
FP-X Application cassette
Quantity
used
Control unit
C14
C30
C60
AFPX-DA2
1
○
○
○
2
－
○
○
AFPX-A21
1
○
○
○
2
－
○
○
AFPX-DA2 + AFPX-A21
Each 1
－
○
○
AFPX-DA2 + AFPX-COM5
Each 1
○
○
○
AFPX-A21 + AFPX-COM5
Each 1
○
○
○
AFPX-A21 + AFPX-DA2 + AFPX-COM5
Each 1
－
○
○
AFPX-DA2 1unit + AFPX-COM5 1unit
－
○
○
AFPX-A21 2units + AFPX-COM5 1unit
－
○
○
Note) In the voltage output range, when using them with the output current at 1 mA to 10 mA, the
condition is the same as the current output range.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Programming Tool Restrictions
Restrictions on usable programming tools depending on the units (as of Feb. 2009)
Type of programming tool
Type of unit
AFPX-C14R
AFPX-C30R
AFPX-C60R
AFPX-C14T, C14TD, C14P, C14PD
AFPX-C30T, C30TD, C30P, C30PD
AFPX-C60T, C60TD, C60P, C60PD
Windows software FPWIN GR Ver.2 Used
(Ver. 2.5 or later)
Used
(Ver. 2.70 or later)
FPWIN GR Ver.1
Not used
Not used
Windows software
Conforms to
IEC61131-3
FPWIN Pro
Ver.6
Used Used
FPWIN Pro
Ver.5
Used
(Ver. 5.1 or later)
Used
(Ver. 5.22 or later)
Handy programming
unit
AFP1113V2
AFP1114V2
Not used Not used
AFP1113
AFP1114 Not used Not used
AFP1111A
AFP1112A
AFP1111
AFP1112
Not used Not used
FP memory loader AFP8670
AFP8671
Used
(Only programs and system registers can be transmitted.)
Note: Precautions concerning version upgrade
• In case of using FPWIN GR Ver.1, please purchase upgrade model FPWIN GR Ver.2.
• FPWIN GR Ver. 2.0 can be upgraded to Ver. 2.5 or later free of charge at our web site.
• FPWIN Pro Ver. 6.0 can be upgraded free of charge at our web site.
• The handy programming unit cannot be used.
Do not download any programs for other units such as FP1 to the FP-X using the handy programming
unit.
Website address:
http://panasonic-denko.co.jp/ac/e/dl/software-list/patch/plc.jsp
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Chapter 1
Features, Functions and Restrictions
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

1.1 Features and Functions of the Unit
Features
• Compact size general-purpose PLC that is suitable for the small-scale facility control.
• Can be directly connected to a personal computer using USB communication port.
• High dimensional security functions to deal with copying programs.
• Supports analog control.
• Following items are provided as options,
- Application cassettes, such as the positioning control function by the high-speed counter and
pulse output.
- Fulfilling communication cassettes.
- Realtime clock function.
Basic functions as compact size general-purpose PLC suitable for the small-scale facility control
Basic functions including the followings are equipped even though it is a general-purpose style such as
AC power supply, screw terminal block and relay output.
1. 32k-step program capacity
2. 0.32 µs command processing speed
3. Max. 382-points I/O control
Single-phase 8-channel and 2-phase 4 channel high-speed counter functions are equipped for
the control unit.
Fulfilling function enhancement
Various add-on cassettes are available as options (such as 10 types of application cassettes and
6 types of communication cassette).
• Application cassettes
DC 8-point input type, transistor 8-point NPN output type, transistor 6-point PNP output type, DC 4-point
input + transistor 3-point NPN output type, analog 2-ch output type, analog 2-ch input + analog 1-ch
output type, thermocouple 2-ch type, RTD 2-ch type, analog 2-ch input type, high-speed counter input +
pulse output type, master memory type with realtime clock (32k-step program can be copied and stored.)
• Communication cassettes
1-ch RS232C type, 2-ch RS232C type, 1-ch RS485/RS422 changeover type, 1-ch RS232C + 1-ch
RS485 type, Ethernet + 1-ch RS232C type, 2-ch RS485 type
FP0 expansion units can be connected as well as the exclusive expansion unit.
A maximum of 3 FP0 expansion units can be connected using the expansion FP0 adapter.
A personal computer can be directly connected with the USB communication port.
A personal computer can be directly connected with the USB cable (excluding C14).
The USB⇔RS232C conversion adapter/cable is not necessary.
(A tool port (RS232C) is also equipped.)
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

High dimensional security functions to deal with copying programs.
The uploading disabling function prohibits uploading (reading) programs in the PLC main unit and
prevent illegal copying.
(It also enables to transfer the programs to the FP-X master memory cassette, when the uploading
disabling function is specified).
The protection for programs can be selected from
3 security methods.
• 4-digit password
• 8-digit password
•
Uploading disabling
A full range of communication functions
Using the Tool port (RS232C) provided as a standard feature on the main unit, communication can be
carried out with a display panel or computer. Additionally, communication cassettes with RS232C,
RS485 and Ethernet interfaces are available as an option. Installing a 2-channel RS232C type
communication cassette in the FP-X makes it possible to connect two devices with RS232C port. A full
lineup of communication functions means you can also work with 1:N communication (up to 99 units)
and PC(PLC) link function (up to 16 units).
Controlling two devices with RS232C port with one FP-X
When using the 2-channel RS232C type communication cassette
1:N communication possible with up to 99 stations (units)
When using the 1-channel RS485/RS422 type communication cassette
When using the 1-channel RS485 and 1-channel RS232C in combination
Link with FP2 and FPΣis possible
Data sharing between small size and medium size PLCs is easily achievable in one network.
The FP-X supports MEWNET-W0, and the programless PLC link with the FP2 or FPΣ is possible.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Supports Modbus RTU
It can be used as a master unit/slave units (F145 and F146 instructions).
It can be easily communicated with a temperature control device, inverter, FP-e or overseas PLCs.
It is possible to communicate with up to 99 units
MEWTOCOL communication
It can be used as a master unit/slave units (F145 and F146 instructions).
It can be easily communicated with a PLC, image processor, temperature control device, message
runner or eco-power meter.
It is possible to communicate with up to 99 units
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Positioning control supported through high-speed counter and pulse output
With the FP-X Tr type, a high-speed counter function can be used by using the CPU I/O.
With the FP-X Ry type, a high-speed counter and pulse output functions can be used by using the pulse
I/O cassette. The pulse output function supports frequencies of up to 100kHz, enabling positioning
control using a stepping motor or servo motor.
Note) The pulse I/O cassette cannot be used for the FP-X Tr type.
Measurement using high-speed counter supported
Increment input mode, decrement input mode, 2-phase input mode, individual input mode, and direction
discrimination mode are supported.
Note) Differs depending on combinations.
Positioning control based on pulse output supported
Pulse/direction and clockwise/counter –clockwise output are supported.
Heater control based on PWM output function supported
The pulse output at any duty ratio can be picked up with special instruction.
Analog potentiometer (volume dial)
An analog potentiometer (volume dial) is provided as a standard feature. This can be used in
applications such as analog timers, without using the programming tools.
Realtime clock function can be added
Optional FP-X master memory cassette (AFPX-MRTC) and backup battery enables the realtime clock
function.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

1.2 Unit Types
1.2.1 FP-X Control Units
C14
C30
C60
Product No. No. of I/O
points
Specifications
Power supply
Input
Output
Connection
Relay type (Ry type)
AFPX-C14R 8/6
100 to 240 V AC
24 V DC
(Common
polarities
+ & - common)
Relay Terminal block
AFPX-C30R 16/14
AFPX-C60R 32/28
AFPX-C14RD 8/6
24 V DC
AFPX-C30RD 16/14
AFPX-C60RD 32/28
Transistor type (NPN) (Tr type)
AFPX-C14T 8/6
100 to 240 V AC
24 V DC
(Common
polarities
+ & - common)
Transistor
(NPN) Terminal block
AFPX-C30T 16/14
AFPX-C60T 32/28
AFPX-C14TD 8/6
24V DC
AFPX-C30TD 16/14
AFPX-C60TD 32/28
Transistor type (PNP) (Tr type)
AFPX-C14P 8/6
100 to 240 V AC
24 V DC
(Common
polarities
+ & - common)
Transistor
(PNP) Terminal block
AFPX-C30P 16/14
AFPX-C60P 32/28
AFPX-C14PD 8/6
24V DC
AFPX-C30PD 16/14
AFPX-C60PD 32/28
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

1.2.2 FP-X Expansion Unit
E14/E16 E30
Product No. No. of I/O
points
Specifications
Power supply
Input
Output
Connection
Relay type (Ry type)
AFPX-E16R 8/8 - 24 V DC
(Common polarities
+ & - common)
Relay Terminal
block
AFPX-E30R
16/14
100 to 240 V AC
AFPX-E30RD
16/14
24 V DC
Transistor type (NPN) (Tr type)
AFPX-E16T 8/8 - 24 V DC
(Common polarities
+ & - common)
Transistor
(NPN)
Terminal
block
AFPX-E30T
16/14
100 to 240 V AC
AFPX-E30TD
24V DC
Transistor type (PNP) (Tr type)
AFPX-E16P
8/8
-
24 V DC
(Common polarities
+ & - common)
Transistor
(PNP)
Terminal
block
AFPX-E30P
16/14
100 to 240 V AC
AFPX-E30PD 24V DC
Input-only type
AFPX-E16X 16/0
(X300 to X30F) -
24 V DC
(Common polarities
+ & - common)
- Terminal
block
- The input specifications are the same as AFPX-E16R.
Output-only type (Relay type)
AFPX-E14YR 0/14
(Y300 to Y30D) - - Relay Terminal block
- The output specifications are the same as AFPX-E16R.
An 8-cm expansion cable is provided with expansion unit
1.2.3 FP-X Expansion FP0 Adapter
Name
Specifications
Product No.
FP-X Expansion
FP0 adapter (with 8
cm expansion
cable, power supply
cable)
For connecting FP0 expansion unit AFPX-EFP0
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

1.2.4 Add-on Cassettes (Communication cassettes/Application cassettes)
Name
Specifications
Product No.
Communication
cassette
FP-X Communication cassette
5-wire 1-channel RS232C
AFPX-COM1
FP-X Communication cassette
3-wire 2-channel RS232C
AFPX-COM2
FP-X Communication cassette 1-channel RS485/RS422
(insulated)
AFPX-COM3
FP-X Communication cassette 1-channel RS485 (insulated)
3-wire 1-channel RS232C AFPX-COM4
FP-X Communication cassette
2-channel RS485 (insulated)
(non-insulated between
channels)
AFPX-COM6
FP-X Communication cassette Ethernet,
3-wire 1-channel RS232C AFPX-COM5
Application
cassette
FP-X Analog input cassette 2-channel analog input
(non-insulated)
AFPX-AD2
FP-X Analog output cassette
2-channel analog output
(insulated) (insulated
between channels)
AFPX-DA2
FP-X Analog I/O cassette
2-channel analog input
(insulated) + 1-channel
analog output (insulated)
AFPX-A21
FP-X Thermocouple cassette
2-channel thermocouple input
(insulated) (insulated
between channels)
AFPX-TC2
FP-X RTD cassette
2-ch RTD input (insulated)
(insulated between channels)
AFPX-RTD2
FP-X Input cassette 8-point DC input AFPX-IN8
FP-X Output cassette
8-point transistor output
(NPN)
AFPX-TR8
6-point transistor output
(PNP) AFPX-TR6P
FP-X I/O cassette 4-point DC input + 3-point
transistor output (NPN)
AFPX-IN4T3
FP-X Pulse I/O cassette 2-ch high-speed counter +
1-ch pulse output AFPX-PLS
FP-X Master memory cassette Master memory + realtime
clock
AFPX-MRTC
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]