Panasonic WVCU161C - SYSTEM CONTROLLER User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Model No. WV-CU161C
System Controller
Operating Instructions
System ControllerWV-CU C
5
4
1
SHIFT
ESC
ALARM
ALARM
OPERATE
RESET
CAMERA
SETUP
SETUP
SLOW
PROGRAM
SET
PRESET
HOME WIDE
WIPER
AUX 1 AUX 2
DEF
PATROL
PLAY
CLOSE
NEAR FAR
LR
UP
DOWN
OPEN
TELE
ZOOM
IRIS
FOCUS
PATROL STOP PATROL LEARN
AUTO
B/W
AUTO FOCUS
IRIS RESET
PROGRAM
PRESET
CAMERA
FUNCTION
SUSPEND
2
0
6
3
9
8
7

2
The serial number of this product may be found on the bot-
tom of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
Serial No.
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is
intended to alert the user to the pres-
ence of uninsulated "dangerous voltage"
within the product's enclosure that may
be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilat-
eral triangle is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions
in the literature accompanying the appli-
ance.
CAUTION: TOREDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SA 1965
SA 1966
NOTE: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
FCC Caution: To assure continued compliance, (example -
use only shielded interface cables when connecting to com-
puter or peripheral devices). Any changes or modifications
not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate this equip-
ment.
For U.S.A
Caution:
Before attempting to connect or operate this product,
please read the label on the bottom.
ENGLISH VERSION

3
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not use near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the points
where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart
is used, use caution when moving the cart/apparatus combination to avoid injury from tip-overs.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or objects fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
S3125A
IMPORTANT SAFETY INSTRUCTIONS

4
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ........................................................................................................................................ 3
FEATURES .................................................................................................................................................................................... 5
PREFACE ...................................................................................................................................................................................... 5
PRECAUTIONS ............................................................................................................................................................................. 6
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ...................................................................................................... 7
■Front View .............................................................................................................................................................................. 7
■Rear View ............................................................................................................................................................................... 9
INSTALLATION ............................................................................................................................................................................. 10
■Mounting in the Rack ............................................................................................................................................................. 10
CONNECTION & SETTING ........................................................................................................................................................... 11
■System Connection ................................................................................................................................................................ 11
■Connection with a Time Lapse VCR ...................................................................................................................................... 14
■Cable-loss Compensation Setting ......................................................................................................................................... 14
■RS-485 Connection ................................................................................................................................................................ 15
■Switch Setting ........................................................................................................................................................................ 16
SETUP MENU ............................................................................................................................................................................... 19
■Displaying the Setup Menu ................................................................................................................................................... 19
■Buttons & Controls used in Setup Menu ................................................................................................................................ 19
■Alarm Setup ........................................................................................................................................................................... 20
■System Setup ......................................................................................................................................................................... 22
■Preset Data Loading .............................................................................................................................................................. 22
■Communication Setup ........................................................................................................................................................... 25
OPERATING PROCEDURES ........................................................................................................................................................ 26
CAMERA CONTROL FUNCTIONS ............................................................................................................................................ 26
■Pan/Tilt Control ...................................................................................................................................................................... 26
■Lens Control .......................................................................................................................................................................... 26
■Operation of Combination Camera ........................................................................................................................................ 27
■Camera Housing Control ....................................................................................................................................................... 30
■External Device Control ......................................................................................................................................................... 30
ALARM CONTROL FUNCTIONS ............................................................................................................................................... 31
■Alarm Operation .................................................................................................................................................................... 31
■Alarm Reset ........................................................................................................................................................................... 31
■Alarm Suspend ...................................................................................................................................................................... 31
CAMERA SETUP ....................................................................................................................................................................... 32
ALL RESET ................................................................................................................................................................................... 34
SPECIFICATIONS ......................................................................................................................................................................... 35

5
PREFACE
The WV-CU161C System Controller is designed for one-to-one use with a Combination Camera or WV-RC100/WV-RC150
Receiver that is provided with camera control functions. You can operate the pan/tilt head, lens and patrol play function from
the controller in normal operations. The camera setup upload/download and other functions are also available on the setup
menus. The distance between the camera and controller may vary depending on the system. The controller can transmit cam-
era control commands via an RS-485 line or a coaxial cable. A time lapse VTR (VCR), alarm sensors and a video monitor can
be connected to the controller.
FEATURES
The WV-CU161C offers the following features when used with a combination camera.
• Pan/tilt control: Manual Pan/Tilt Slow ON/OFF, Auto Panning ON/OFF, Sequence Sort/Random
• Lens control: Iris, Zoom, Focus with Auto-focus
• Preset position memories: Up to 64 positions including HOME
• Patrol: Learning/Play
• Image selection: Color/Black and White
• Alarm control: Suspension ON/OFF, Reset
Note: The WV-CU161C will not perform audio communications even if an audio board is installed in the connected Receiver.

6
PRECAUTIONS
• Refer all work related to the installation of this
product to qualified service personnel or system
installers.
• Do not block the ventilation opening or slots on the
cover.
Place the appliance at least 5 cm (2 inches) away from
the wall to prevent the appliance from heating up.
• Do not drop metallic parts through the slots as this
could permanently damage the appliance.
Turn the power off immediately and refer servicing to
qualified service personnel if any foreign parts fall
through the slots.
• Do not attempt to disassemble the appliance.
Do not remove any screws or covers as doing so can
cause electric shocks.
There are not any user-serviceable parts inside. Refer
maintenance to qualified service personnel.
• Handle the appliance with care.
Do not strike or shake the appliance as this may dam-
age the appliance.
• Do not expose the appliance to water or moisture.
Do not try to operate it in wet areas.
Take immediate action if the appliance becomes wet.
Turn the power off and refer servicing to qualified ser-
vice personnel. Moisture can damage the appliance
and can also cause electric shocks.
• Do not use strong or abrasive detergents to clean
the outside of the appliance.
Use a dry cloth to clean the appliance when it is dirty. If
the dirt is hard to remove, then use a mild detergent
and wipe gently.
• Do not operate the appliance beyond its specified
temperature, humidity or power source ratings.
Do not use the appliance in an extreme environment
where there are high temperatures or high humidity.
Use the appliance at temperatures within –10˚C and
+50˚C (14°F to 122°F) and where the humidity below 90
%.
The input power source for this appliance is 120 V AC
60 Hz.

7
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
■Front View
qOperate Indicator (OPERATE)
Lights up while the System Controller power is on.
wAlarm Indicator (ALARM)
Blinks when an alarm is activated.
The blink changes to a steady light when the alarm is
automatically reset.
Press the ALARM RESET button to turn the indicator off.
eAuto Panning/Black and White Selection/Patrol Stop
Button (AUTO/B/W/PATROL STOP)
AUTO: Pressing this button will activate the auto pan-
ning function of cameras that are provided with this
feature.
B/W: Pressing this while the SHIFT indicator is lit will
display the picture in black and white on the moni-
tor.
PATROL STOP: Pressing this button while holding
down the CAMERA SETUP button will stop pro-
gramming the camera patrol learning function.
The four following Auto Panning modes can be selected
by pressing the AUTO button in combination with but-
tons 1 to 4
For further information, refer to the Operating Instruc-
tions for the individual combination cameras.
AUTO PAN ON or Functions set on a combination
camera:
Simply press this button or press button 1 and
then this button.
AUTO SORT ON: Press button 2 and then this button.
AUTO SEQ ON: Press button 3 and then this button.
RANDOM PAN ON: Press button 4 and then this but-
ton.
rPatrol Play/Patrol Learn Button
(PATROL PLAY/ PATROL LEARN)
Pressing this button will start the camera patrol play
function. Pressing this button while holding down the
CAMERA SETUP button will start to program the cam-
era patrol learning function.
System Controller WV-CU C
1 2 3
4 6
7 8 9
0
5
SHIFT
OPERATE ALARM
RESET
SLOW
SUSPEND
CAMERA
SETUP
PATROL
PLAY
PROGRAM
PRESET
CAMERA
FUNCTION
SETUP
ESC
HOME
SET
PRESET WIDE TELE
NEAR
AUX1
B/W
AUTO
PATROL STOP PATROL LEARN
WIPER
AUX2
DEF
UP
DOWN
RL
FAR
FOCUS
IRIS
ZOOM
CLOSE OPEN
PROGRAM
ALARM
IRIS RESET
AUTO FOCUS
q w re t
u
y
o!1 !0 i!2
!3
!4
!5
!6

8
tWiper/Auxiliary 1 Button (WIPER/AUX1)
Pressing this button will turn the housing wipers on or
off for cameras provided with this function. Pressing this
while the SHIFT indicator is lit will turn on or off the
AUX1 function controlling accessories that are connect-
ed to the camera or the specified receiver.
The indicator next to the respective button is lit while
the wiper or AUX1 operates.
yDefroster/Auxiliary 2 Button (DEF/AUX2)
Pressing this button will turn the housing defroster on or
off for cameras provided with this function. Pressing this
while the SHIFT indicator is lit will turn on or off the
AUX2 function controlling accessories that are connect-
ed to the camera or the specified receiver.
The indicator next to the respective button is lit while
the defroster or AUX2 operates.
uJoystick Controller (UP/DOWN/L/R)
This joystick manually operates the Pan/Tilt Head and
moves the cursor in the Setup menu on the monitor
screen.
UP: Upward
DOWN: Downward
L: Left
R: Right
iFocus Buttons (FOCUS: NEAR/FAR)
These buttons are used to adjust the lens focus of cam-
eras equipped with the specified lens.
When these buttons are pressed simultaneously, the
lens focus is set automatically when the specified cam-
era is used.
oZoom/Iris Buttons
(ZOOM: WIDE/TELE, IRIS: CLOSE/OPEN)
These buttons are used to zoom the camera image in
(TELE) and out (WIDE).
The lens iris is adjusted by pressing the OPEN or
CLOSE button while the SHIFT indicator is lit. Hold
down these buttons simultaneously for 1 second while
the SHIFT indicator is lit in order to reset the iris back to
the factory setting.
!0 Preset/Set/Program Preset Button
(PRESET/SET/PROGRAM PRESET)
PRESET: This button is used combined with the numer-
ic buttons to move a specific camera to a preset
position.
SET: This button is used to execute the currently high-
lighted setting in the Setup menu.
PROGRAM PRESET: Pressing this while holding down
the CAMERA SETUP/SETUP/PROGRAM button will
program a preset position.
!1 Numeric Buttons (0-9)
These buttons are used for the numeric input of preset
numbers and for executing parameters on the Camera
Setup menu.
!2 Home/Escape Button (HOME/ESC)
HOME: This button is used to return a specific camera
to the home position.
ESC: This button is used to escape from the currently
highlighted selection and return to the previous
menu of the Setup Menu.
!3 Shift button (SHIFT)
Pressing this button will enter or quit the shift mode.
While the SHIFT indicator is lit, press or hold down a
button that is assigned to a special function in the shift
mode in order to activate or deactivate the function.
!4 Alarm Reset/Suspend Button
(ALARM RESET/SUSPEND)
Pressing this button while the alarm function is activat-
ed will reset the system alarm.
Pressing this button while the SHIFT indicator is lit will
activate or deactivate the alarm suspension mode.
The LED next to the button is lit while the alarm suspen-
sion mode operates.
!5 Camera Setup/Setup/Program Button
(CAMERA SETUP/SETUP/PROGRAM)
Pressing this button for 2 seconds or more will open or
close the Camera Setup menu.
Pressing this button for 2 seconds or more while the
SHIFT indicator is lit will open or close the controller
setup menu. The indicator next to the respective button
is lit while the setup window is operated.
This button is also used to program the camera patrol
learning and preset position functions.
!6 Slow/Camera Function Button
(SLOW/CAMERA FUNCTION)
The pan/tilt speed will decrease if this button is pressed
while the joystick controller is moved.
Pressing this combined with the numeric buttons while
the SHIFT indicator is lit will execute the camera func-
tions.

9
■Rear View
POWER
OFF
SIGNAL GND
ON
CAMERA
IN
RS485ALARM DATA
TERM
VIDEO
OUT
RESET OUT
ALARM IN
RECOVERIN
ALARMOUT
ALARM IN LINE COAX
RS485
4
2
ON
OFF
12G34
RT ABABG
rty u i o !0 !1e
q w
qAlarm Switch
This switch is used to specify the functions for the 5-pin
terminal adjacent to the switch. When the switch is set
to the upper position, the terminals supply and accept
the alarm related signals with a Time Lapse VCR. When
the switch is in the lower position, the terminals accept
alarm inputs 1, 2, 3 and 4.
wAlarm Terminals
Terminal functions are specified by the alarm switch
position as shown in the table. Refer to page 14 for con-
nection with a Time Lapse VCR.
eRS-485 Terminal
This terminal is used to exchange control data with the
camera site.
rTermination Switch (TERM ON/OFF)
This switch is used to terminate the RS-485 communi-
cation lines.
It should normally be kept in the ON position.
tLine Selection Switch (LINE 4/2)
This switch is used to select full-duplex (4-lines) or half-
duplex (2-lines) for the communication lines.
yData Selection Switch (DATA COAX/RS485)
This switch selects the data communication route from
among the multiplexing data on a coaxial cable or when
using an RS-485 line.
uVideo Output Connector (VIDEO OUT)
This connector supplies composite video signals from
the camera.
iCamera Input Connector (CAMERA IN)
This connector accepts the multiplexed video and con-
trol data signals from the specified camera or a speci-
fied receiver.
oAC Cord
!0 Power Switch (POWER)
This switch is used to turn the System Controller power
on and off.
Caution: In the following cases, disconnect the AC
cord from the service outlet, or switch off an ALL-
POLE MAIN SWITCH with a contact separation of at
least 3 mm in each pole incorporated in the electri-
cal insulation of the building.
This is to be used when the controller needs to be
isolated from the AC mains, when the controller will
not be used for a long time, and when there is light-
ning.
!1 Signal Ground Terminal (SIGNAL GND)
Pin #
1
2
G
3
4
Switch Position
Up
Alarm Input
Alarm Output
Signal ground
Recover Input
Reset Output
Down
Alarm Input 1
Alarm Input 2
Signal ground
Alarm Input 3
Alarm Input 4

• Installation should be performed by qualified service personnel or system installers according to the following instruc-
tions.
• Disconnect the power cord from the service outlet before installation.
10
INSTALLATION
■Mounting in the Rack
1. Remove the Connector Panel and Bottom Cover from
the controller by removing the four screws.
2. Mount the Connector Panel onto the bottom by using
the two screws that were removed above.
3. Mount the Bottom Cover onto the rear by using the two
screws that were removed above.
4. Remove the side panels by removing the four screws.
5. Remove the Palm Rest Panel by removing the two
screws.
6. Fix the Rack Mounting Angles onto both sides by using
the four screws.
7. Mount the controller in the EIA standard 19-inch rack.
Note: Always keep the temperature in the rack within 45°C
(122°F).
Connector Panel 1
Bottom Cover
Bottom Cover
Connector Panel
3
2
SystemController WV-CU
5
4
1
2
0
6
3
9
8
7
System Controller WV-CU
5
4
1
2
0
6
3
9
8
7
4
4
5
7 (Procured locally)
5 (Procured locally)
(Supplied:
WV-Q62)
6
6
(Supplied:
WV-Q62)
Rack Mounting Angle
(Optional Accessory: WV-Q62)
Palm Rest Panel
Side Panel
(Left)
Side Panel
(Right)
CAUTION

11
CONNECTION & SETTING
■System Connection
●Basic Connection
The WV-CU161C can be connected with a camera, a Time Lapse VCR and a video monitor as in the typical system configura-
tion shown below.
Combination Camera
WV-CU161C
Time Lapse VCR
System Controller WV-CU C
123
4 6
789
0
5
SHIFT
OPERATE ALARM
RESET
RESET
SUSPEND
CAMERA
SETUP
PATROL
PLAY
PROGRAM
PRESET
CAMERA
FUNCTION
SETUP
ESC
HOME
SET
PRESET WIDE TELE
NEAR
AUX1
B/W
AUTO
WIPER
AUX2
DEF
UP
DOWN
RL
FAR
FOCUS
IRIS
CLOSS OPEN
PROGRAM
ALARM
IRIS RESET
AUTOFOCUS
Video Monitor
Camera Site
Control Site
ALARM INPUT/OUTPUT
(See page 14)
CAMERA
IN
VIDEO
OUT
VIDEO IN
VIDEO OUT
DATA
COAX
RS485
900 m or less
(Using RG-59U,
BELDEN 9259 or
equivalent cable)
(Coaxial Multiplex
Communication)
Note: Refer to the operating instructions of each system component for connection and operation.

12
●Connecting more Cameras
A bi-directional video switcher purchased separately can be installed when connecting more than one camera. Video signal
reception, camera control and alarm input reception are only available between the camera selected and the controller due to
the nature of the switcher.
Combination Camera
Video Switcher
Camera Housing
Camera
Receiver
R
System Controller
WV-CU161C
System Controller WV-CU C
1 2 3
4 6
7 8 9
0
5
SHIFT
OPERATE ALARM
RESET
RESET
SUSPEND
CAMERA
SETUP
PATROL
PLAY
PROGRAM
PRESET
CAMERA
FUNCTION
SETUP
ESC
HOME
SET
PRESET WIDE TELE
NEAR
AUX1
B/W
AUTO
WIPER
AUX2
DEF
UP
DOWN
L
FAR
FOCUS
IRIS
CLOSS OPEN
PROGRAM
ALARM
IRIS RESET
AUTOFOCUS
Video Monitor
Time Lapse VCR
DATA
COAX
RS485
CAMERA
IN
VIDEO
OUT
VIDEO IN
VIDEO OUT
Note: Refer to the operating instructions of each system component for connection and operation.

13
●Connecting with a Distant Camera Site
Using two Network Interface Units, that is a Transmitter and a Receiver, will help to extend the distance between the camera
and control sites. An RS-485 is used when the communication line is extended for more than 1200 m (400 ft).
WV-CS854A Network Interface Unit
Network Interface Unit
R
System Controller
WV-CU161C
System Controller WV-CU C
123
4 6
789
0
5
SHIFT
OPERATE ALARM
RESET
RESET
SUSPEND
CAMERA
SETUP
PATROL
PAY
PROGRAM
PRESET
CAMERA
FUNCTION
SERUP
ESC
HOME
SET
PRESET WIDE TELE
NEAR
AUX1
B/W
AUTO
WIPER
AUX2
DEF
UP
DOWN
L
FAR
FOCUS
IRIS
CLOSS OPEN
PROGRAM
ALARM
IRIS RESET
AUTOFOCUS
Video Monitor
DATA PORTTransmitter
Receiver
DATA PORTVIDEO OUT
CAMERA IN
VIDEO OUT
RS-485 Cable
Coaxial Cable
RS485 DATA
TERM LINE
COAX
RS485
4
2
ON
OFF
RT ABABG
Public lines
Video signal
RS-485 signal
Camera Site
Control Site
Notes:
• Refer to the operating instructions for each system component for connecting and operating them.
• If the public line is busy, then it may cause instability for the system operation.

14
■Connection with a Time Lapse VCR
Alarm in/out and recover-reset in/out are connected between the time lapse VCR and the rear of the controller.
Note: Use a relay as shown below when connecting an indicator such as a buzzer that exceeds 16 V DC 100 mA.
ALARM IN
1
2
G34
Relay
+12 V
NC NO
Alarm Indicator etc.
Time Lapse VCR
1 ALARM IN
2 ALARM OUT
G GROUND
3 RECOVER IN
4 RESET OUT
NC: Normally Closed Contact
NO: Normally Open Contact
2 4 ALARM
IN
1
COM2
ALARM
RESET IN
3
ALARM
RECOVER OUT
4
ALARM
OUT
5
135
■Cable-loss Compensation Setting
The maximum allowable cable length between a camera and a controller is 900 m (3 000 ft) when using an RG-59U BELDEN
or equivalent cable. Cable loss compensation can be adjusted in the setup menu as S, M or L.
Camera WV-CU161C
A m (A ft)
0 (0)≤A < 400 m (1 300 ft) →S
400 (1 300)≤A < 700 m (2 300 ft) →M
700 (2 300) ≤A < 900 m (3 000 ft) → L
Cable compensation
parameter in WV-CU161C
Setup menu
Cable length (with RG-59U
BELDEN 9259 or equivalent)
Unit: m (ft)

15
■RS-485 Connection
Control data is transmitted and received between the con-
troller and other peripherals. Use a shielded cable of data
communication grade, consisting of two twisted pairs suit-
able for RS485. Cable length may be extended up to 1 200
m (4 000 ft).
●Internal Diagram
Note: Make sure to turn the DATA switch on the rear of the
controller to RS-485 position.
TR
RS485
ABABG
GND
5TB TA RB RA 4321
RA
TB
4
3
2
1
TA
RB

16
■Switch Setting
There are four switches on the rear of the controller for specifying the terminal definition and data communication conditions.
A signal form selection switch (SW1) and a character display mode switch (SW100) are mounted inside the controller. These
inner switches do not need to be adjusted when the controller is used with the factory default settings.
●Rear Panel Setting
Alarm Terminal Definition Switch
This switch specifies the functions for the 5-pin terminal. The default setting is the upper position.
Upper position: Used when connecting with a Time Lapse VCR. The terminals function as ALARM IN, ALARM OUT,
RECOVER IN and RESET OUT.
Lower position: Used when connecting with multiple alarm sensors. The terminals function as ALARM IN 1-4.
Termination Switch
This switch opens or terminates the RS-485 line. The default setting is ON.
ON: Used when connecting one to one. The line is terminated by a 150-ohm resister.
OFF: The line is open.
Line Switch
This switch specifies the RS-485 communication mode. Match it to the mode used by the connected devices. The default set-
ting is 4.
4: 4-line full duplex
2: 2-line half duplex
Data Switch
This switch specifies the data communication route between the controller and the camera. The default setting is COAX.
COAX: Control commands and status information are transmitted and received through a coaxial cable.
RS485: Commands and status are transmitted and received through an RS-485 cable connected to the RS-485 terminal.
RS485 DATA
TERM LNE COAX
RS485
4
2
ON
OFF
RT ABABG
Rear Panel
ALARM
RESET OUT
ALARM IN
RECOVERIN
ALARMOUT
ALARM IN
12G34

17
Recover Output Switch (SW1)
1. Remove the bottom cover by removing the two screws.
The SW1 mounted inside the controller can be seen.
2. Set the SW1 to the desired position. The default setting
is 0/5V.
0/5V: 0V or 5V output, active when it is 5 V.
O.C: Open collector output, active when it is low.
Control capacity is 16 V 500 mA maximum.
3. Place the bottom cover as it was before and fasten the two screws.
Display mode Switch (SW100)
1. Remove the bottom cover as described above.
2. Remove the two side panels and the bottom panel by removing the twelve screws. The SW100 mounted inside the con-
troller can be seen.
●Internal Switch Setting
Bottom
Cover
Panasonic
SW1
SW1
O.C 0/5V
SW100
Side Panel
Bottom Cover
Side Panel
• The internal switch setting should be performed by qualified service personnel or system installers.
• Unplug the controller power cord from the electric outlet before setting the internal switch in order to reduce the risk of
electric shocks.
Caution:
The internal switches, SW1 and SW100, can be readjusted to change the recover output signal form or character display mode
from the default settings.

3. Set the SW100 to the desired position. The default set-
ting is NOR.
NOR: White letters are displayed with a black border.
REV: Black letters are displayed with a white border.
4. Place the side panels, bottom panel and bottom cover
in their previous positions and fasten the screws that
were previously removed.
SW100
NOR REV
18

19
SETUP MENU
The SETUP MENU has four main submenus: Alarm Setup, System Setup, Preset Data Load and Communication.
All of these main menus are further divided into submenus.
ALARM SETUP ......................................................................................................... Page 20
SYSTEM SETUP ....................................................................................................... Page 22
PRESET DATA LOAD ................................................................................................Page 22
COMMUNICATION .................................................................................................... Page 25
SETUP MENU
■Displaying the Setup Menu
1. Check that the camera, monitor and peripherals are
correctly and securely connected.
2. Switch all the system components on.
The operation indicator of the WV-CU161C lights up,
and the picture of the camera appears on the monitor.
3. Press the CAMERA SETUP/SETUP/PROGRAM button
for 2 seconds or more while the SHIFT indicator is lit.
4. The SETUP MENU appears.
Note: The COMMUNICATION parameter appears when the
DATA switch is set to RS-485 (See page 16).
■Buttons & Controls used in the
Setup Menu
SHIFT button + CAMERA SETUP/SETUP/PROGRAM
button:
Press the CAMERA SETUP/SETUP/PROGRAM button
for 2 seconds or more while the SHIFT indicator is lit.
PRESET/SET/PROGRAM PRESET button:
Press this button to confirm the parameter selection or
to enter a submenu for an item marked with .
HOME/ESC button:
Press this button to return to the previous menu.
WV-CU161C SETUP MENU *.**
ALARM SETUP
SYSTEM SETUP
PRESET DATA LOAD
COMMUNICATION
PROGRAM
PRESET
SET
PRESET
ESC
HOME
SHIFT
CAMERA
SETUP
SETUP
PROGRAM
Up: To select a setup item.
Down: To select a setup item.
Left: To decrease the parameter.
Right: To increase the parameter.
DOWN
LR
UP
LR
UP
DOWN
R
UP
DOWN
LR
•Joystick Controller

•Closing Setup Menu
Press the PRESET/SET/PROGRAM PRESET button for 2
seconds or more while the SHIFT indicator is lit.
The SETUP indicator goes off.
Note: The new settings are not saved if the WV-
CU161C power is turned off before completing the
setup. Return to the WV-CU161C SETUP MENU,
complete the setup, and then turn the power off to
save the new settings.
■Alarm Setup
Alarm related functions are set up.
1. Display the WV-CU161CC SETUP MENU.
2. Move the cursor to ALARM SETUP , and then press
the SET button.
The setup menu appears depending on the ALARM
switch setting on the rear of the controller.
ALARM PRESET appears on the bottom of the menu
when the ALARM switch is set to the upper position to
connect with a time lapse VCR.
ALARM TERMINAL appears on the bottom of the
menu when the ALARM switch is set to the lower posi-
tion to connect with four sensors.
Alarm Display Setting
This item lets you select whether or not to display an
“ALARM” text line on the monitor when an alarm is activat-
ed.
1. Display the ALARM SETUP menu.
2. Move the cursor to ALARM DISPLAY.
3. Select ON or OFF using the joystick, and then press the
SET button. The factory setting is ON.
ON: Display is enabled.
OFF: Display is disabled.
20
Note: The display time differs depending on the Alarm
Output Setting.
Site Alarm Setting
This item lets you enable or disable the controller to receive
the camera site alarm.
1. Display the ALARM SETUP menu.
2. Select SITE ALARM by moving the joystick up or down.
3. Select SITE ALARM ON or OFF by moving the joystick
to the right or left.
The initial factory setting is ON.
ON: The controller receives the site alarm (Video Motion
Detection: VMD) issued by the camera.
OFF: The site alarm is disabled.
Terminal Alarm Setting
This item lets you enable or disable the controller to receive
the alarm signal from the alarm connector.
1. Display the ALARM SETUP menu.
2. Select TERM.ALARM by moving the joystick up or
down.
3. Select TERM.ALARM ON or OFF by moving the joystick
to the right or left.
The initial factory setting is ON.
ON: Alarm activation through the terminal is received.
OFF: Alarm activation through the terminal is no
received.
Alarm Output Setting
This item lets you select the duration that the following three
functions continue working for after an alarm activation.
• The ALARM is displayed on the monitor (ALARM DIS-
PLAY ON mode).
• The alarm is output to external devices (from the
ALARM OUTPUT connector).
• The buzzer sounds (ALARM BUZZER ON mode).
1. Display the ALARM SETUP menu.
2. Select ALARM OUTPUT by moving the joystick up or
down.
3. Select the desired alarm output duration of 1S-30S,
40S, 50S, 1MIN, 2MIN, 3MIN, 4MIN, 5MIN EXT or OFF
by moving the joystick to the right or left.
The initial factory setting is 10S.
EXT: The alarm signal continues to be output from the
alarm output connector until the alarm is reset. The
alarm is not automatically reset.
1S-5MIN: The alarm signal is only supplied from the
alarm output connector for the set time. The alarm is
automatically reset after the set time. The ALARM
indicator changes from blinking to a steady light.
OFF: No alarm output signal is supplied. (The alarm is
deactivated.)
ALARM SETUP
ALARM DISPLAY ON
SITE ALARM ON
TERM.ALARM ON
ALARM OUTPUT 10S
ALARM BUZZER ON
ALARM PRESET –
ALARM SETUP
ALARM DISPLAY ON
SITE ALARM ON
TERM.ALARM ON
ALARM OUTPUT 10S
ALARM BUZZER ON
ALARM TERMINAL