Panasonic VL-SWD501AZ User manual

Installation Guide
Note to the installer
■ Beforeattemptingtoconnectoroperatethisproduct,pleasereadthelabelontherearof
themainmonitor.
■
Pleasereadthis guide carefully,andinstalltheproductsafelyandcorrectlybyfollowing
theinstructions.Carefullyreadtheinformationfoundinthesectiontitled"Foryoursafety"
inparticular.
■ Onlyuseattachments/accessoriesspecifiedbythemanufacturer.
■ Theinstallationshallbecarriedoutinaccordancewithallapplicableinstallationrules.
■ Panasonicassumesnoresponsibilityforinjuriesorpropertydamageresultingfromfailures
arisingoutofimproperinstallationoroperationinconsistentwiththisguide.Additionally,
anyresultingmalfunctionwillnotbecoveredunderthewarranty.
■ Afterinstallation,makesuretoleavethisguidewiththecustomer.
For the Installation of door station
and main monitor station
•VL-V554BXisasurfacemounttype,VL-V554UBX
isaushmounttype.
For your safety
Topreventsevereinjuryandlossoflife/property,readthissectioncarefullybeforeusingthe
producttoensureproperandsafeoperationofyourproduct.
WARNING
Preventingre,electricshockandshortcircuits
● Leaveinstallationworktothedealer.
Installationworkrequirestechniqueandexperiences.Failuretoobservethismay
causere,electricshock,injury,ordamagetotheproduct.Consultthedealer.
● Electricalconnectionworkshouldbeperformedbycertiedpersonnelonly.Certication
isrequiredforperformingelectricalconnectionwork.Consultyourdealer.
● UseonlythespeciedpowersupplyunitandACcable.
● Donotattempttodisassembleor modifythis product.Contact anauthorised service
centreforrepairs.
● Neverinstallwiringduringalightningstorm.
● Donotconnectnon-specieddevices.
● Donotconnectapowercabletoaterminalthatisnotspeciedinthisguide.
● Whenopening holesinwallsfor installation orwiring, orwhen securingthepower
cable,makesureyoudonotdamageexistingwiringandductwork.
● Donotmakeanywiringconnectionswhenthepowersupplyisturnedon.
● Donot usethesuppliedpowersupply unitforoutdoor installations(itis forindooruse
only).
● Donotinstallthemainmonitorandpowersupplyunitinthefollowingplaces:
- Placeswherethemainmonitorandpowersupplyunitmaybesplashedwithwateror
chemicals.
- Placeswherethereisahighconcentrationofdust,orhighhumidity.
● Donot performanyactions(such asfabricating,twisting,stretching, bundling,forcibly
bending,damaging,altering,exposingtoheatsources,orplacingheavyobjectsonthe
powercable)thatmaydamage the power cable. Using the product with adamaged
powercablemaycauseelectricshock,shortcircuits,or fire. Contact an authorised
servicecentreforrepairs.
● W hen e xist ing c hime  wire s are u sed,  it is  poss ible  that  they  cont ain AC v olta ge.
Contactanauthorisedservicecentre.
● Donotinstall oruse theproduct inhealth carefacilities ifany regulationspostedin
the area instruct you not todo so. Hospitals or health care facilities maybe using
equipmentthatcouldbesensitivetoexternalRF(radiofrequency)energy.
● D o not  ins tall  or us e th is pr oduc t ne ar au toma tic ally  cont rol led d evic es s uch a s
automaticdoorsandfirealarms. Radio waves emitted from this product may cause
suchdevicestomalfunction,resultinginanaccident.
Preventingaccidentsandinjuries
CAUTION
● Ifthewiringisunderground,donotmakeanyconnectionsunderground.
● Ifthewiringisunderground,useaprotectiontube.
● Ifthewiringisoutdoors,useaprotectiontubeorasurgeprotector.
● Install theproduct securely adheringto theinstructionsin thisguide to prevent it from
fallingoffthewall.Avoidinstalling onto low-strength walls, such as gypsum board,ALC
(autoclavedlightweightconcrete),concreteblock,orveneer(lessthan18mmthick)walls.
Preventingelectricshock
Preventinginjury
1-62,4-chome,Minoshima,Hakata-ku,Fukuoka812-8531,Japan
©PanasonicSystemNetworksCo.,Ltd.2014
PNQW4430ZA C0814MM0
VL-V554BX/
VL-V554UBX
VL-MWD501BX
Doorstation Mainmonitorstation
Doorstationisdescribedas"doorphone"
andMainmonitorstationisdescribedas
"mainmonitor"inthisguide.
ModelNo. VL-SWD501AZ
VL-SWD501UAZ
Wireless Video Intercom System
Supplied accessories for installation
■ For the doorphone
Mounting
base×1
(AZonly)

Flush
mounting
box×1
(UAZonly)
Screw×4(Usedwhen
installingthedoorphone)
(AZ
 :4mmx12mm)
(UAZ:4mmx25mm)
Nameplate×2
(incl.1spare) Hexwrench×1
■ For the main monitor

Mounting
bracket×1 Cablebinder×1 Screw×2
(4mmx16mm)
■ Power supply unit and related items
Powersupply
unit×1
(PartNo.VL-PS241) ACcable×1
Cablebinder×1
Screw×2
(4mmx40mm)
Toavoidmalfunctionorcommunicationdisturbances,donotinstallthedoorphoneorthemain
monitorinthefollowinglocations:
- Placeswherevibrationoranyotherkindofimpactoccurs.
- Placeswhereechoingisfrequent.
- Placesnearahighconcentrationofdust,hydrogensulphide,ammonia,sulphur,ornoxious
fumes.
■
For the doorphone
● Ifastronglightisshining onthedoorphone,the visitor’sfacemaynotbedistinguishable.Do
notplacethedoorphoneinthefollowinglocations:
- Wheremostofthebackgroundisthesky.
- Wherethebackgroundisawhitewall,anddirectsunlightwillreectoffit.
- Wheredirectsunlightwillshineonthedoorphone.
● Donot place thedoorphone in locationswhere echoingoccurs, as thiswill cause the
doorphonetobeepfrequently.
● Dustprotection/waterprotectionisIP54.
Onlywheninstallationworkspeciedinthisguideisproperlyperformedandappropriatewater
protectiontreatmentisperformed.
● Makesuretherearofthedoorphoneisnotsubjecttowater.
● Dependingontheinstallationlocation,condensationmayformonthedoorphone’slenscover.
Thismaycauseimagestobecomeobscured.Condensationwilldissipateasthetemperature
rises.
■
For the main monitor
● Installthe main monitoraway fromelectronic appliancessuch asTVs,radios, personal
computers,airconditioners,boilercontrolpanelswithintercom, home security equipment,
wirelessdevices,ordigitalcordlessphones.
● Donotinstallthemainmonitorinplaceswhereitwillbeaffectedbyextremelyhigh-frequency
radio waves(near broadcasting antennasetc.). Thismay cause thedisplay to icker oran
interruptingnoisetooccur.
● Leaveat least 20cm ofspace above,below, andto theleft and rightsides ofthe main
monitor.Donotinstallonawallthatisdeeplyrecessed.
● Donotinstallthemainmonitorinsideawall.
● Besuretoinstallthemainmonitormorethan5mawayfromthedoorphone.
● Theproduct operates inthe frequency rangeof 1.88 GHzto 1.90 GHz,and the RF
transmission power is 250mW (max.). Refer tothe "For best performance"section in the
OperatingInstructions.
● Inareassurrounded bya highelectrical eld,disturbances mayoccur inthe mainmonitor’s
imageorsound.
Important:
●You will need the following additional items to install and congure the doorphone
and the main monitor.
[Locally procured]
- DCcableandwires(fordoorphoneandotherconnections):
Prepareacableandwiresoftheappropriatespecication.( "Wiretypeandlength")
Note:
● Theillustrationsinthesuppliedmanual(s)mayvaryslightlyfromtheactualproduct.
Precautions for installation
Wiring schematic diagram
Setupcorrectlyaccordingtothefollowingwiringschematicdiagramand"Wiretypeandlength".
●Forinformation,suchasordernumbers,aboutoptionaldevicesthatcanbeconnectedto,refertothe"Additional/replacementaccessories"sectionintheOperatingInstructions.
ブ
プ
MAIN MONITOR
DOORPHONE 1
DOORPHONE 2
POWER SUPPLY UNIT
Connectiondeviceforoptionoutput(Acontact)
NP: Non-polarised
Power
supply
Power
supply
12VAC/DC
12VAC/DC
Electriclock
Electriclock
24VDC
Wire type and length
Wiringrun
Wiretype*1
Diameter Length(Max.)
Mainmonitor–
Doorphone A
ø0.65mm 22AWG 100m
ø1.0mm 18AWG 130m
ø0.5mm CAT5 50m
Mainmonitor–
Powersupplyunit B
ø0.65mm 22AWG 10m
ø1.0mm 18AWG 20m
Doorphone–
Electriclock*2 Cø0.5mm-ø1.2mm
(24AWG-17AWG)
Accordingtospeci-
cationofconnected
device.
Mainmonitor–
Connectiondeviceforoption
output(Acontact)*2
Dø0.5mm-ø1.2mm
(24AWG-17AWG)
Accordingtospeci-
cationofconnected
device.
*1Type:Single-paircablewithoutersheath(jacket)
Conductor:Coppersolid
● Acertiedpowersupplywiringhastobeusedwiththisequipment.Therelevantnational
installationand/orequipmentregulationsshallbeconsidered.Acertiedpowersupplywiring
notlighterthanordinarypolyvinylchlorideexiblewiringaccordingtoIEC60227shallbeused.
*2Whenusinganelectriclockoraconnectiondeviceforoptionoutput(Acontact),selectadevice
thatmeetsthefollowingguidelines:
● Electriclockconnectionterminal(S1/S2):
- N/Odryclosurecontact
- 12VAC/DC,lessthan1A
● Connectiondeviceforoptionoutput(Acontact)terminal(OUT1/OUT2):
- 24VAC/DC,lessthan0.3A(minimumcontact:5VDC1mA)
A
C
C
D
B
NP
NP
NP
NP
NP
NP
&screw×2
(3.8mmx20mm)

ScrewA
Youcanusethe[Wide/Zoomsettings]settingonthemainmonitortoselecttheareathat
isvisiblewhenavisitorcalls;availablesettingsare[Wide],[Zoom],and[All](entireimage
display).(Defaultsetting:[Wide])
● T he fo llow ing v alue s are  for  when  the d oorp hone  is in stal led i n the  stan dar d pos itio n
(thecentreofthedoorphone’sheightisapproximately1,450mm)and at a distance of
approximately500mmfromthecameralens.
■ Installation height and area visible by the camera lens
When set to zoom
Displaysaportionofthewideimageat2timesthesize.
● B ecau se a d igi tal z oom i s use d, t he im age q ual ity o f zoo m
displayislowerthanthatofwidedisplayorentireimagedisplay.
Imagedisplayedon
mainmonitor:
● You canuse themain monitor’s[Zoomposition settings]setting toselect thedesired area
visiblewhenzooming.
Refertothefollowingandcongurethemainmonitor.
Entire image display
Theareaaboveandbelowthewideimageisvisible.
Important:
● Onthe bottomsurfaceofthedoorphone andthemountingbase,there areholestoallowwater
todrain.Donotcoverthemupwheninstalling.
● Whenexistingwiring(suchaschimewires)isused:
- ItmaycontainACvoltagethatmaycauseelectricshockand/ordamagetheproduct.
- Neverusethefollowingtypesofwiring.Consultaqualiedtechnician/dealer.
VL-V554BX VL-V554UBX
1 Attachthemountingbasetothewallsecurely.
Mountingbase
(accessory)
Wire(locallyprocured)
Wall
83.5mm
Screws(accessory)×2
● Installthemountingbaseonaverticalatwall.
1 Installtheflushmountingboxinthe
wall.
Flushmountingbox(accessory)
100mm
Knockouthole*1
151mm
37mm
*1Onlyopentheknockoutholesas
requiredforthewiring.
2 Useahexwrench(accessory)toloosenscrewAandremovethefrontpanelofthedoor-
phone.

ScrewA
Frontpanel
2mmhexwrench
(accessory)
3 Connectthewires.
Terminalforthe
mainmonitor
<Rear view>
Terminalfortheelectric
lock
●Recommendedtorque:
0.5N·m{5.1kgf·cm}
●Maximumtorque:
0.7N·m{7.1kgf·cm}
3-1Loosenthescrews.
3-2Pushinthewirestotheterminalconnectors(non-polar),thentightenthescrews.
4 Attachthedoorphonetothemounting
base.
Screws(accessory)×4
4 Attachthedoorphonetotheflushmounting
box.

Screws(accessory)×4
5 AttachthenameplatetothedoorphoneandusescrewAtosecurethefrontpanel.
● Writethenameonthenameplateasneeded.
● Recommendedtorque:
0.35N·m{3.6kgf·cm}
Nameplate
(accessory)
ScrewA
Approx.500
Approx.170°
Approx.2,250
Imagerange
Approx.115°
Approx.500
Imagedisplayedon
mainmonitor:
Approx.1,600
Approx.650
Approx.1,450
Upanddown Leftandright(whenlookingfromabove)
Up Imagerange
Approx.2,050
Approx.500
Centreof
doorphone
Approx.45°
Centre (default)
Approx.45°
Approx.500
Imagerange
Approx.1,650
Down
Approx.45°
Approx.500
Approx.1,400
Imagerange
Left
Approx.1,500
Approx.1,450
Approx.550
Approx.1,450 Approx.1,250
Approx.400
Installing the doorphone
■ About the installation location
● TheAC cableplug isused asthe maindisconnect device.Ensure thatthe poweroutletis
installedneartheproductandiseasilyaccessible.
● Areadilyaccessibledisconnectdeviceshallbeincorporatedexternaltotheequipment.
- Externaldisconnectdevicemustbecertiedandhaveacreepageandclearancedistance
of3mmormore.
■ Precautions for wiring
● Makesurethatthepowersupplyunitisunpluggedbeforeperforminganywiringwork.
● AlwaysconnectACorDCcablestotheappropriateconnectororconnectionterminal.
● To preventthe DCcable fromdisconnecting andto preventelectric shock,secure theDC
cableusingthecablebinder(accessory)andattachthecablecover.
How to connect the AC cable and DC cable
1 StriptheDCcableasfollows:
<DCcable>
7mm
25mm
2 Removethescrew(B)andthenremove
thecablecover(A).
3 ConnecttheACcable(accessory)totheAC
INconnectoronthetopofthepowersupply
unit.Next,connecttheDCcable(locally
procured)totheDCOUTterminalonthe
bottomofthepowersupplyunit,andthen
securethewiresbytighteningthescrews.
● Recommendedtorque:0.45N·m{4.6kgf·cm}
<Frontview>
ACcable
DCcable
Screws
*1
Cablebinder(accessory)
4 Usethecablebinder(accessory)tosecure
theDCcable(double-coatedarea)tothe
powersupplyunit.
5 Attachthepowersupplyunittothewall.
("Wallmounting",below)
6 Makesuretoreplacethecablecover(A).
Connectthepowersupplyunit(accessory),theACcable(accessory),andaDC
cable(locallyprocured).
CAUTION
Insertthecablesfirmlyalltheway
intotheconnectorandterminal.
Ifthecablesarenotinsertedall
theway,heatmaybegenerated.
*1Makesurethattherearenobarewires
exposedoutsidetheproduct.
Screw(B)
Cablecover(A)
DCOUTterminal
ACINconnector
<Topview>
<Bottomview>
DCcable
binderhole
Power supply unit (with cable cover
removed)
Wall mounting
Attachthepowersupplyunittothewallsecurely.
Wall
Screws
(accessory)×2
Main monitor installation position
Installing the main monitor
Mainmonitor
installationposition
82.5mm
82.7mm
2 ConnecttheDCcableandwires.
● Connectthewirescorrectlyaccordingto"Wiringschematic
diagram".
3 Mountthemainmonitortothemountingbracket.
3-1 Lineupthetabonthebottomofthebracketwiththegrooveonthemainmonitor(A).
3-2 Lineupthetabonthetopofthebracketwiththegrooveonthemainmonitor,and
pushthemainmonitordownuntilitissecure(B).
Wall
1 Attachthemountingbrackettothewall
securely.
● Installthemountingbracketon avertical
atwall.
ARemovescrewAandthenremovethe
terminalcover.
B LoosenscrewBandpushinthewiresof
theDCcabletotheterminalconnectors
(non-polar),thentightenthescrews.
● Recommendedtorque:
0.8N·m{8.2kgf·cm}
CUsethecablebinder(accessory)to
securetheDCcable(double-coated
area)tothemainmonitor.
D Makesuretoreplacetheterminalcover.
How to connect the DC cable:
Whilepressingonthebuttonwithapoint-
edobjectsuchasascrewdriver,insert
thewireintotheterminalconnector.(To
disconnectawire,whilepressingonthe
button,pulloutthewire.)
Barewireattip
9mm
Terminal
Button
Wiringfrom
doorphone
Important:
Donotconnectthepowercable.
(Damagemayoccur.)
How to make wiring connections:
Resetbutton
SDcard
slot
20cm
20cm
20cm
20cm
Cablebinder
(accessory)
12mm
Barewireattip ScrewB
■ About the installation position of the main monitor and mounting bracket
● Forthefollowingreasons,leaveatleast20cmofspace
above,below,and totheleft andrightsides ofthemain
monitor:
-Topreventmalfunctionandsoundcuttingout
-ToensureSDcardscanbeinsertedandremoved,
andtomakesuretheresetbuttoncanbeused
(theSDcardslotisonthesideofthemainmonitor;
theresetbuttonisonthebottom)
● Placethemainmonitor inalocationthatyoureyesarethesame heightasthecentre
ofthedisplay.
● Afterdecidingwheretoinstallthemainmonitor,attach
the  mount ing b racke t in t he loc atio n show n on t he
right.
Doorphone installation position Installing the power supply unit
Imagerange:
Approx.900
Approx.500
Approx.85°
Approx.170°
Centre (default)
Imagerange:
Approx.900
Approx.85°
Right
Imagerange:
Approx.900
Approx.500
Approx.170°
Approx.85°
Approx.500
Approx.850
Approx.1,450
Approx.550
32mm
When set to wide (default)
Centreof
doorphone
Centreof
doorphone
Centreof
doorphone
Approx.95°
Centreof
doorphone
Approx.1,450
Approx.500
Approx.900
Approx.170°
Approx.500
Approx.1,100
Approx.2,000
Imagerange
Imagedisplayedon
mainmonitor:
Viewwhenlooking
fromabove
Viewwhenlooking
fromabove
(Units:mm)
Notes about electrical wiring
Makesurenottopinchthewires(asshowntothe
right)onthemountingbracketwheninstalling.
● Donotforciblyattachtothemountingbracket.
Vertical,flatwall
Screws
(accessory)
Holeinwall
83.5
60
7
50
Mountingbracket
(Units:mm)
(Units:mm)
(Units:mm)
(Units:mm)