Panasonic WV-PB5504AE User manual

Pin No. Designation
-1-
Video Output Board
WV-PB5504AE
Before attempting to connect or operate this product, please read these instructions completely
PREFACE
The WV-PB5504AE Video Output Board is provided for expanding the video output capability of the
Matrix Switcher.
APPEARANCE
1. Alarm Output/Reset Output Connector (ALARM OUT/RESET OUT)
External Timing Input Connector (EXT TIMING IN)
Recover Input Connector (RECOVER IN)
ALARM OUT: When the Matrix Switcher receives an alarm from the WV-PB5564E Alarm Board
or camera site receivers WV-RC100, WV-RC150 or WV-RC170, the alarm output signal is
provided at this connector for the Time Lapse VTR. The active pin number of the alarm out-
put depends on the alarm mode set by the on-screen programme (Mode-1, Mode-2,
Mode-3).
RESET OUT: When the Matrix Switcher resets the activated alarm, the alarm reset output sig-
nal, either Open Collector or pulse, is provided at this connector for the Time Lapse VTR.
EXT TIMING IN: The camera switching interval (Sequential Dwell Time) can be synchronized
with the lapse mode set in the Time Lapse VTR.
EXT. TIMING IN 1 controls Monitor 1 output, EXT. TIMING IN 2 controls Monitor 2 output, etc.
Supply the camera switching pulse from the Time Lapse VTR to this connector. Minimum
duration for camera switching pulse needs to be more than one (1) second.
RECOVER IN: This connector accepts the alarm recover signal from the Time Lapse VTR.
When handling this board, hold only by circuit board edges. Otherwise components on the
board may be damaged by static electricity.
Caution
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
ALARM OUT 1
RESET OUT 1
RECOVER IN 1
Ground
EXT TIMING IN 1
Ground
ALARM OUT 2
RESET OUT 2
RECOVER IN 2
Ground
EXT TIMING IN 2
(+5V DC)
ALARM OUT 3
RESET OUT 3
RECOVER IN 3
Ground
EXT TIMING IN 3
Ground
ALARM OUT 4
RESET OUT 4
RECOVER IN 4
Ground
EXT TIMING IN 4
Ground
Ground
OUT
IN
OUT
IN
OUT
IN
OUT
IN
MONITOR
ALARM OUT
RESET OUT
EXT TIMING IN
RECOVER IN
OUTPUT
1
2
3
4
q
w
25 13
24
23
22
21
20
19
18
17
16
15
14
12
11
10
9
8
7
6
5
4
3
2
1

BOARD
NO.
-2-
BOARD SETTING
Before installing this board, the following settings should be made by qualified service personnel or system installers.
1. Set switches (SW1) on the board to meet the monitor output number as shown in the following table.
Initially, monitor 1-4 is selected at the factory.
1234
OFF
SW1
SW4
SW5
SW3
SW2
12
OFF
SW6
SW100
SW150
SW200
SW250
2. Monitor Input/Output Connector (MONITOR IN/OUT)
OUT: The video signal selected by the Matrix Switcher is provided at this connector for the video monitor.
IN: This connector is used for video input from a VTR or system expansion to 128 camera input.
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1
2
3
4
5
6
7
8
1-4
5-8
9-12
13-16
1-4
5-8
9-12
13-16
MONITOR
OUT NO. SW1 SETTING
Be careful when setting these switches as the swtches are not physically
located on the board in numerical order. Switch location from the top of the
board, going downward, is: SW4 (reset out 3), SW5 (reset out 4), SW3
(reset out 2) and SW2 (reset out 1).
2. Set switches (SW2/SW3/SW4/SW5) on the board to choose the alarm
reset output signal as either Open Collector (OPEN C.) or Pulse (VTR).
Open Collector (OPEN C.):16VDC 100mA max.
Pulse (VTR):+5VDC approx. 500 msec.
Initially, VTR positions are selected at the factory.
CH1
OPEN C
VTR
Note

PAL TEST
NOR
SW6
NTSC OFF
12
These switches are used only for factory test.
Always keep these switches in the positions as shown on the right in the
field.
Note
4. Confirm switches (SW6) on the board are set to the following positions.
BOARD
NO.
1 (5) 1 2 3 4
2 (6) 5 6 7 8
3 (7) 9 10 11 12
4 (8) 13 14 15 16
MONITOR OUT NO.
SW100 SW150 SW200 SW250
3. Set switches (SW100/SW150/SW200/SW250) on the board to choose the
character display mode on the monitor.
NOR: White with Black border
REV: Black with White border
Initially, normal (NOR) positions are selected at the factory.
NOR REV NOR REV
NOR Position REV Position
The following installation should be made by qualified ser-
vice personnel or system installers.
1. Remove the screws from the rear panel(s) of the
Matrix Switcher.
2. Remove the rear panel(s).
3. Place the Video Output Board into the desired position
in the rear of Matrix Switcher by sliding it inside the
board guides.
INSTALLATION
Before installing this board be sure to turn off the Power
Switch of the Matrix Switcher.
Caution
Each slot is identical, so the board can installed in any
slot.
However it is recommended to install the board as
shown below for an orderly installation.
Note
CPU
RS-232C
TIME
ADJUST IN
COM
PRINTER
OUT
IN
VS/VD
VD
OUT
OFF
+9V
+5V
− 5V
POWER
ON
11A00001
OUT
IN
1
OUT
IN
2
OUT
IN
3
OUT
IN
4
MONITOR
ALARM OUT
RESET OUT
EXT TIMING IN
RECOVER IN
OUTPUT
MONITOR
ALARM OUT
RESET OUT
EXT TIMING IN
RECOVER IN
MONITOR
ALARM OUT
RESET OUT
EXT TIMING IN
RECOVER IN
MONITOR
ALARM OUT
RESET OUT
EXT TIMING IN
RECOVER IN
OUT
IN
1
OUT
IN
2
OUT
IN
3
OUT
IN
4
OUTPUT
OUT
IN
1
OUT
IN
2
OUT
IN
3
OUT
IN
4
OUTPUT
OUT
IN
1
OUT
IN
2
OUT
IN
3
OUT
IN
4
OUTPUTINPUT
1
2
3
4
5
6
7
8
CAMERA IN
VIDEO OUT1
VIDEO OUT2
INPUT
1
2
3
4
5
6
7
8
CAMERA IN
VIDEO OUT1
VIDEO OUT2
INPUT
1
2
3
4
5
6
7
8
CAMERA IN
VIDEO OUT1
VIDEO OUT2
INPUT
1
2
3
4
5
6
7
8
CAMERA IN
VIDEO OUT1
VIDEO OUT2
INPUT
1
2
3
4
5
6
7
8
CAMERA IN
VIDEO OUT1
VIDEO OUT2
INPUT
1
2
3
4
5
6
7
8
CAMERA IN
VIDEO OUT1
VIDEO OUT2
INPUT
1
2
3
4
5
6
7
8
CAMERA IN
VIDEO OUT1
VIDEO OUT2
INPUT
1
2
3
4
5
6
7
8
CAMERA IN
VIDEO OUT1
VIDEO OUT2
33-64
ALARM
TEST
1-32
00
5
RESET
MODE
CONTROL
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
DATA 6
DATA 7
DATA 8
TEST 1
TEST 2
Alarm Board
Video Input Board Video Output Board
Rear Panel(s)
Remove screws.
-3-

4. Make sure to push in the Video Output Board until it is
seated firmly.
5. Secure the Video Output Board by tightening the two
screws on the board.
6. Close off open spaces on the rear of the Matrix
Switcher by using WV-Q63E Blank Panels (Optional)
or supplied rear panel(s).
(Refer to the instructions for WV-Q63E)
Refer to the Operating Instructions of WJ-SX550A for
more details.
Note
SPECIFICATIONS
Monitor Output (1 - 4): 1.0V[p-p]/75Ωcomposite video signal
Monitor Input (1 - 4): 1.0V[p-p]/75Ωcomposite video signal
Alarm Output (1 - 4): Open collector output: 16VDC 100mA max.
Reset Output (1 - 4): Pulse (VTR): +5VDC 500msec. or
Open collector output: 16VDC 100mA max.
External Timing Input (1 - 4): Pulse 5V[p-p] interval time more than one second
Recover Input (1 - 4): Make Contact or Open collector Input
Contact time more than 0.5 second
Interval time more than two seconds
Character Generator: Camera ID; 30 characters (15 x 2 lines)
Character Style; White with Black Border
Black with White Border
Dimensions: 24.5 (W) x 265 (H) x 260 (D) mm
15/16” (W) x 10-7/16”(H) x 10-1/4” (D)
Weight: 400g(0.9 lbs.)
Weight and dimensions indicated are approximate.
specifications are subject to change without notice.
N0296-0 YWV8QA4192AN Printed in Japan
N 19
Matsushita Electric Industrial Co., Ltd.
Central P.O. Box 288, Osaka 530-91, Japan
Blank Panel
or
Tighten screws.
Tighten screws.
Video Output Board