Panasonic NS1000 User manual

CLASSROOM MATERIAL
(TRAINER)
NS1000

Introduction
This material refers to the KX-NS1000 PBX system, and details the basic information that should be
covered in a classroom session (1 day)
The Session comprises of the following sections;
NS1000 – Installation & Initialisation
NS1000 – WebMC
NS1000 – Terminal Registration
NS1000 – User Profiles
NS1000 – DSP Resources
NS1000 – Networking
NS1000 – Upgrade & Backup
NS1000 - Maintenance
From following this course element, participants will be gain an understanding of how to install,
initialize and maintain the NS1000 system.
Further information about feature implementation and specifications, may be found in the
associated Installation Manual, Feature Guide and User Manual.

INSTALLATION AND
INITIALIZATION
Section - 1

Introduction
This material refers to the KX-NS1000 PBX system, and details the basic steps necessary to install
and initialize the unit.
The Module comprises of the following sections;
NS1000 – Installation
NS1000 – System Initialization
From following this course element, participants will be gain an understanding of how to install
and initialize the NS1000 ready for first use.
Further information about feature implementation and specifications, may be found in the
associated Installation Manual, Feature Guide and User Manual.

Contents
Chapter 1 Installation
1.1 Unpacking
1.2 Component Location
1.3 Option Installation
1.4 Rack Mounting
1.5 Desk Mounting
1.6 Wall Mounting
1.7 Earth / Surge Protector connection
1.8 Connecting Power
1.9 External Connections
Chapter 2 System Initialization
2.1 System Initialization
2.2 Web Console Preparation
2.3 Web Console Connection
2.4 1st Login
2.5 Easy Setup
Chapter 3 Slave Initial Configuration
3.1 Slave Initial Configuration
3.2 Slave Registration
Chapter 4 System Outline
4.1 UPS Connection and setting

INSTALLATION
Chapter 1

NOTE
IMPORTANT:
Before installing the NS1000 system, refer to the Installation Manual. The Installation Manual
contains specific information regarding the safe installation of the unit and also details specific
installation and wiring precautions.
The information contained in this presentation is intended to supplement the NS1000 Installation
Manual by providing an overview of the installation and initialization process and in no way replaces
the published Installation Manual.
Where any information contained herein appears unclear or incomplete, the information contained
in the published NS1000 Installation Manual shall take precedence.

Description Quantity
NS1000 Main Unit 1
AC Cord 1
19” Rack-mounting bracket 2
AC Cord Hook Clip 1
Screws 6
1.1 Unpacking (1)
Unpacking
Remove the NS1000 from the box and check that the following items are present;

1.2 Component Location (1)
Component location (External)
The main ports, jacks and LEDs etc are shown below;
AC IN
AC cord clamp
AC SW GROUND Serial port FAN
System mode SW USB port IP ports
LED indicators MOH/EPG ports DPH Port (Option) Legacy Slot (Option)
Front Side
Back Side

1.2 Component Location (2)
Component location (Internal)
The expansion/option slots are shown below;
Slot
(FAX Server)
Slot
(Doorphone)
Slot
(Trunk/SLT)
Slot
(Storage Memory)
Slot
(DSP 2)
Slot
(DSP 1)

1.3 Option Installation (1)
Option Installation
•Optional cards can be installed when the top cover is removed.
•Option Cards are not “Hot-Swap”
•Power must be removed from the unit before optional cards are installed
1. Ensure the Power
Switch is ‘OFF’
2. Remove 3 screws from
the rear of the top cover.
NB: Where possible, Option cards should be installed before installing and powering-on the unit for the first time. When this is
not possible, the system must first be ‘SHUTDOWN’ using the Web Maintenance Console.
Removing the power without shutting down the unit may damage the systems file-structure and render the system inoperable.

Option Installation
The required options can now be installed.
1.3 Option Installation (2)
CAUTION:
When installing or removing option cards, do not put pressure on the main board. Damage to the option and main board may result.
3. Remove the cover
4. Install the required options
5. Replace the top cover and screws.

1.4 Rack Mounting
Rack Mounting the NS1000
The NS1000 can be rack-mounted using the supplied brackets and screws.
1. Mount the brackets onto the NS1000.
2. Bolt the NS1000 into the rack using the hardware supplied by the rack manufacturer.
Size = 2U
Dimensions:
430mm×88mm×340mm
Weight : Under 4.5kg
(Fully Mounted)
NB: Ensure that there is sufficient ventilation around the system and that the rack temperature limit is not exceeded.
(Refer to the Installation manual for further details)

1.5 Desk Mounting
Desk Mounting the NS1000
The NS1000 can be installed on a flat surface.
•The unit MUST be placed flat on it’s base (Not on it’s back, sides or upside-down etc)
•The units FAN opening MUST be clear
•A 10cm gap around the sides and 20cm over the top of the unit MUST be maintained.
•DO NOT place flammable (wood etc) objects behind the unit (Refer to the Installation Manual for more
details)

NB: The unit must be installed with the arrows on the Wall Mounting brackets pointing “UP”.
In any other orientation, the unit will not be secured correctly to the wall and may fall.
1.6 Wall Mounting
Wall Mounting the NS1000
The NS1000 can be installed onto a suitable wall using the optional Wall Mounting kit.
(Refer to the Installation Manual for further details)
1. Install the screws
(with suitable wall anchors etc)
2. Mount the unit to the wall
(using the Wall Mounting Kit)

WARNING
•Proper connection to earth is very important to reduce the risk to the user of electrocution or to protect the PBX from the effects of
external noise or lightning strike.
•The earth wire of the AC cable has an effect against external noise and lightning strikes, but it may not be enough to protect the PBX
and to ensure electromagnetic compatibility. A permanent connection between earth and the earth terminal of the PBX must be
made.
•To protect the system from electrical surges, it is strongly recommend to connect the system to a surge protector that meets the
following specifications:
•Surge arrestor type: 3-electrode arrestor
•DC spark-over voltage: 230 V
•Maximum peak current: at least 10 kA
Many countries/areas have regulations requiring surge protection.
Be sure to comply with all applicable laws, regulations, and guidelines.
Frame Ground Surge Protection
1.7 Earth / Surge Protector connection
Frame Ground (Earth) and Surge Protection
(Refer to the Installation Manual!)

AC Cord Clip
Connect the other end of the AC
Cord to the UPS System.
UPS System:
A UPS should be connected to the PBX to provide temporary in the event of a power failure.
When using the recommended UPS (APC RS Series with USB interface), the PBX can shutdown automatically by sending a warning signal to
the PBX through the USB port.
By shutting down correctly, data loss or serious damage to the PBX caused by a sudden power cut can be prevented.
When power is restored, turn off the PBX using the power switch first, and then turn the PBX back on before starting the PBX.
1.8 Connecting Power
Connecting the AC Cord
Using the AC Cord supplied with the unit, connect it to the PBX and secure with the supplied AC Cord Clip.

1.9 External connections
Connecting Peripherals and Options
Once the NS1000 has been mounted, various peripherals and options can be connected.
(Refer to the Installation Manual for further details)

SYSTEM INITIALISATION
Chapter 2

After installing the option cards, initialize the system (factory default settings)
1. Ensure the power switch is OFF.
2. Slide the System Mode Switch to the “SYSTEM INITIALIZE” position.
3. Turn the power switch ON. (STATUS and MASTER LED will flash AMBER), the STATUS LED will then
flash GREEN.
4. Slide the System Mode Switch back to the “NORMAL” position. (When the STATUS LED is flashing.)
System Mode
Switch
Indicators
STATUS
BATT
ALARM MASTER 5. When successfully executed, the STATUS indicator will
stop flashing and stay lit. (RED or GREEN)
Refer to Appendix for LED Sequence Detail.
2.1 System Initialisation
STATUS = RED (No DHCP)
STATUS = GREEN (DHCP)
MASTER = Flashing AMBER
(Master/Slave not assigned)