Panasonic ET-PFD465 User manual

MODEL
ET-PFD465
FRAME-EVO-P14 / P14-US
Mounting frame for projectors
The following projectors can be mounted in this frame:
LCD Projectors
PT-MZ16KL
PT-MZ13KL
PT-MZ10KL
These installation instructions must always be provided to the customer

Manual FRAME-EVO-P14 / P14-US
02.01.2020
Page 1of 38

Manual FRAME-EVO-P14 / P14-US
02.01.2020
Page 2of 38
Table of content
1. Preamble ....................................................................................................... 3
1.1 FRAME-EVO-P14 / P14-US designation ......................................................................................3
1.2 Optional accessory designation .................................................................................................4
1.3 Tools required...........................................................................................................................5
2. Safety instructions......................................................................................... 5
3. What’s in the box?....................................................................................... 11
4. Optional Accessories ................................................................................... 12
5. Fitting the projectors in the frame .............................................................. 15
6. Removing the Upper Ring - Installation Version ......................................... 17
7. Reinstalling the Upper Ring ......................................................................... 19
8. Adjustment options..................................................................................... 21
9. Stacking frames ........................................................................................... 23
10. Mounting the frame on a truss.................................................................. 24
11. Maximum stacking information ................................................................ 26
12. System maintenance and inspection (Re-examination)............................ 32
13. Declaration of Conformity ......................................................................... 35
14. Dimensions ................................................................................................ 36
14.1 FRAME-EVO-P14 / P14-US .....................................................................................................36
14.2 FRAME-EVO-P14 / P14-US Installation Version - without the Upper Ring...............................37
Imprint............................................................................................................. 38

Manual FRAME-EVO-P14 / P14-US
02.01.2020
Page 3of 38
1. Preamble
Congratulations on your purchase of the FRAME-EVO-P14 / P14-US projector frame from
EXACT solutions GmbH.
Please read very carefully the instructions provided in this manual. In the following pages
you will find all the information needed for a safe and fast installation.
After the installation is done properly, you can enjoy all the features of your new product.
Please consider keeping the original box and packaging materials, in case you ever need to
ship the frame.
Model number: FRAME-EVO-P14 / P14-US
Copyright © 2020 EXACT solutions GmbH. All rights reserved.
1.1 FRAME-EVO-P14 / P14-US designation
European market
Non-European market
Manufacturer m.no.: FRAME-EVO-P14
Panasonic EU m.no.: ET-RFD50
Manufacturer m.no.: FRAME-EVO-P14-US
Panasonic USA m.no.: ET-PFD465
m.no. = model number
Note: In this manual, when reference is made to the manufacturer model number it is also
automatically a reference to the Panasonic EU / USA model number like described in the
table above

Manual FRAME-EVO-P14 / P14-US
02.01.2020
Page 4of 38
1.2 Optional accessory designation
European market
Non-European market
Manufacturer m.no.: FRAME-PF-UNI-PORAD
Panasonic EU m.no.: ET-CLP-P
Manufacturer m.no.: FRAME-PF-UNI-PORAD
Panasonic USA m.no.: - (non-USA product)
Manufacturer m.no.: FRAME-PF-UNI-CLP5030
Panasonic EU m.no.: ET-CLP50
Manufacturer m.no.: FRAME-PF-UNI-CLP5030
Panasonic USA m.no.: ET-PFD50CLAMP
Manufacturer m.no.: FRAME-PF-UNI-CLP30PT
Panasonic EU m.no.: ET-CLP30
Manufacturer m.no.: FRAME-PF-UNI-CLP30PT
Panasonic USA m.no.: ET-PFD30CLAMP
Manufacturer m.no.: EVO-LINK-200
Panasonic EU m.no.: TBD
Manufacturer m.no.: EVO-LINK-200-US
Panasonic USA m.no.: ET-PFD065TMS2
Manufacturer m.no.: EVO-LINK-201
Panasonic EU m.no.: TBD
Manufacturer m.no.: EVO-LINK-201-US
Panasonic USA m.no.: ET-PFD165TMS2
Manufacturer m.no.: EVO-LINK-210
Panasonic EU m.no.: TBD
Manufacturer m.no.: EVO-LINK-210-US
Panasonic USA m.no.: ET-PFD265TMCX2
Manufacturer m.no.: EVO-LINK-211
Panasonic EU m.no.: TBD
Manufacturer m.no.: EVO-LINK-211-US
Panasonic USA m.no.: ET-PFD365TMCX2
m.no. = model number
Note: In this manual, when reference is made to the manufacturer model number it is also
automatically a reference to the Panasonic EU / USA model number like described in the
table above.

Manual FRAME-EVO-P14 / P14-US
02.01.2020
Page 5of 38
1.3 Tools required
The only tool required is a 4 mm hex key to mount the projector in the FRAME-EVO-P14 /
P14-US.
2. Safety instructions
These installation instructions must always be handed over to the installing person.
1
Read these instructions carefully before installing the system.
INTENDED USE
The FRAME-EVO-P14 / P14-US frame is intended for use by fully qualified, trained and
competent persons to provide safe and secure transportation, installation and adjustment
of projectors.
Only use the frame with projector in a closed environment (conference rooms, theatres,
convention halls, etc.) where there is no wind, moisture, excessive heat etc.
Make sure that only the corresponding projectors are installed in this frame! Do not try to
use it with other projectors because serious accidents can occur!
1
Only a qualified person should install this product
4 mm hex key (Allen key)

Manual FRAME-EVO-P14 / P14-US
02.01.2020
Page 6of 38
WARNINGS
Installation work should only be carried out by a qualified technician.
If this product is not installed correctly, serious accidents may result.
Do not use the FRAME-EVO-P14 / P14-US frame outdoors.
This product is made only for indoor usage. If the FRAME-EVO-P14 / P14-US frame is
mounted outdoor, there are many influences like wind or rain that can have an effect
on the stability of the whole system. This can cause serious accidents and property
damage.
Do not place the frame on top of unstable surfaces.
If the frame is placed on top of a surface which is sloped or unstable, it may fall down
or tip over and injury or damage could result. Make sure that the surface can support
a load of 130 kg (286.601 lbs)
2
plus the weight of all additional equipment as well as
other potential systems.
Do not hang the frame from unstable or inappropriate structures.
If the frame is hung on an unstable structure, the entire system can fall down and
injuries may occur. Make sure that the construction can support a total weight of 130
kg (286.601 lbs) plus the weight of all additional equipment as well as other potential
systems.
Make sure to not exceed max. weight loads for ceiling mounting.
For suspended installations, use only designated hanging accessories, like EVO-LINK-
200 series, FRAME-PF-UNI-PORAD Portrait Adapter and FRAME-PF-UNI-CLP5030,
FRAME-PF-UNI-CLP30PT rigging clamps for a max. weight load of 130 kg (286.601
lbs). Please refer to the corresponding instructions for the accessories used. Please
also refer to chapter “4. Optional Accessories” and “11. Maximum stacking
information”.
2
130 kg (286.601 lbs) = 3 x (weight of heaviest projector + weight of heaviest lens + weight of FRAME-EVO-P14 / P14-US)

Manual FRAME-EVO-P14 / P14-US
02.01.2020
Page 7of 38
For stacking, make sure that all four locking pins pass completely through the female
stacking bolt.
Make sure the four male bolts enter into the correspondent female bolts and are
locked.
Do not install the FRAME-EVO-P14 / P14-US or the projector while people are present
under the mounting zone during the installation process.
When installing the projector, make sure no one is in the area underneath the
installation zone.
Always secure the frame to the rigging truss with a safety steel cable.
The frame should always be secured with an appropriate safety steel cable so that in
case of a malfunction it doesn’t fall more than 5 cm. Please consult the local laws or
regulations regarding the additional safety of hanging equipment.

Manual FRAME-EVO-P14 / P14-US
02.01.2020
Page 8of 38
CAUTION
Before installing the projector in the FRAME-EVO-P14 / P14-US frame, please read the
projector’s user manual. When the projector has a lens attached, please remove it.
The FRAME-EVO-P14 / P14-US frame with the projector inside must be installed only
in an environment that is recommended by the projector manufacturer.
Minimum two persons are required to install the FRAME-EVO-P14 / P14-US frame.
With regard to the overall weight of all necessary installation devices, make sure to
handle those with at least two people.
Make sure that the structure from which you hang up to 3 FRAME-EVO-P14 / P14-US
frames including projectors is capable of carrying the overall weight of approx. 130 kg
(286.601 lbs) plus the weight of all additional equipment as well as other potential
systems.
Prior to any installation, you must do a visual inspection to make sure that the
system is in a good condition. For more information please refer to chapter
“12. System maintenance and inspection (Re-examination)”.

Manual FRAME-EVO-P14 / P14-US
02.01.2020
Page 9of 38
RISK SITUATIONS
Risk of injury due to the possibility of falling objects during the assembly or disassembly of
the FRAME-EVO-P14 / P14-US frame.
Protection objective: avoid injury from falling parts.
Wear appropriate safety shoes, gloves and helmet.
Make sure the area is clear under the frame during installation.
Risk of hitting the head with the FRAME-EVO-P14 / P14-US frame during the hanging set
up process.
Protection objective: avoid injury from hitting the head.
Wear a helmet.
Incorrect installation may lead to certain parts of the FRAME-EVO-P14 / P14-US frame or
the entire FRAME-EVO-P14 / P14-US frame to fall down.
Protection objective: prevent personal injury and property damage.
Double check the FRAME-EVO-P14 / P14-US frame and its installation.
Insufficient load capacity of the supporting structure may lead to certain parts of the
FRAME-EVO-P14 / P14-US frame or the entire FRAME-EVO-P14 / P14-US frame to fall
down.
Protection objective: prevent personal injury and property damage.
Provide adequate dimensioning of the supporting structure. The supporting structure
must be able to support the combined weight of all the equipment attached to, or
hung from it.
Ensure correct installation of the supporting structure.