Panasonic EH-HS95 User manual

© Panasonic Corporation, 2013.
Unauthorized copying and distribution is a violation
of law.
Order Number PEWT1311A62CE
(Household) Hair Straightener
Model No. EH-HS95
Asia
TABLE OF CONTENTS
PAGE PAGE
1 Warning -------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide ----------------------------------------- 3
4 Disassembly and Assembly Instructions ---------------- 5
5 Wiring Connection Diagram ---------------------------------10
6 Schematic Diagram ---------------------------------------------11
7 Exploded View and Replacement Parts List -----------12

2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications

3
3 Troubleshooting Guide
Refer to Wiring Connection Diagram.

4

5
4 Disassembly and Assembly Instructions
4.1. Disassembly Instructions
1. Remove Shaft Cover from Main Body by Slotted screw
driver (Minus Driver).
NOTE:
Use NEW Shaft cover once disassembling due to
easily breakage or looseness of hook.
2. Remove Torx screws at Shaft position by Phillips screw
driver (Star Driver).
3. Remove Shaft out by tiny-shaped Phillips screw drivers
and pull it out from the Main body.
4. Remove Pivot spring by gripping and pulling it out from
the Main body.
5. Remove Slide Lock Plate from Main Body by Slotted
screw driver (Minus Driver).
NOTE:
Use NEW Shaft cover once disassembling due to
easily breakage or looseness of hook.

6
6. Remove Tapping Screw from Housing side and press
Plate side Phillips screw driver (Plus Driver).
7. Remove Housing A from Housing B and remove Press
Plate Cover from Press Plate follow as below drawing.
• When remove Housing A,
Becareful Floating Spring 4 pcs. disappear
8. Take off Iron Plate and (Micro) PCB Assembly 200C from
Housing B.
• Take off Iron Plate from Housing B.
Slide and take off Iron Plate from Hook.
• Take off (Micro) PCB Assembly from Housing B by push
at Hook of Housing B.
9. Remve Tapping Screw from Heater holder B by Philips
screw driver (Plus Driver).

7
10. Take off Iron Plate and (High Voltage Igniter) PCB
Assembly from Press Plate.
• Take off Iron Plate from Press Plate.
• Take off (High Voltage Ignitre) PCB Assembly from Press
Plate.

8
4.2. Assembly Instructions
1. Shaft Cover fixing point. Have control direction.
2. Housing B Assembly Point. When insert Power cord must be surely assembly in Connector Cover follow as below.

9
4.3. Lead wire of Iron Plate (Heater A , Heater B) and Circuit arrangement
points.
1. Lead wire of Iron Plate (Heater A assembly block) and (Micro) PCB Assembly 200C arrangement follow as below.
2. Lead wire of Iron Plate (Heater B assembly block) and (High Voltage Igniter) PCB Assembly arrangement follow as below.
3. Lead wire of Moisture Assembly Block arrangement follow as below.
4. Shaft Cover must be control direction follow as below.

10
5 Wiring Connection Diagram

11
6 Schematic Diagram

12
7 Exploded View and Replacement Parts List
7.1. Exploded View
All parts are supplied from PMFTH-AP through PLAP

13
7.2. Replacement Parts List
Remarks : *1 Individual Available
Safety Ref. No. Part No. Part Name & Description Quantity Remarks
1 EHHS95HSABW HOUSING A ASSEMBLY BLOCK 1
2 EHHS95FSW FLOATING SPRING 4 *1
3 EHHS95HABW HEATER A ASSEMBLY BLOCK 1
4 EHHS95CCAW CIRCUIT BOARD ASSEMBLY BLOCK 1 (INCLUDE 2 INSULATION TUBES)
5 EHHS95HS41BW HOUSING B 1 (FOR EH-HS95-K415 : INDONESIA)
5 EHHS95HS67BW HOUSING B 1 (FOR EH-HS95-K675 : KOREA)
5 EHHS95HS68BW HOUSING B 1 OTHERS
5 EHHS95HS69BW HOUSING B 1 (FOR EH-HS95-K695 : KUWAIT / QATAR )
6 EHHS95SHCBW SHAFT COVER 1
7 EHHS95T3010W TORX SCREW 3*10 1
8 EHHS95CTBW CONNECTOR COVER BLOCK 1
9 EHHS95PC61BW POWER CORD 1 B2 PLUG (M3204)
9 EHHS95PC67BW POWER CORD 1 B2 PLUG (SF868), KOREA
9 EHHS95PC68BW POWER CORD 1 S3 PLUG (UK13A3)
10 EHHS95T2606W TAPPING SCREW 2.6*6 12 *1
11 EHHS952060BW TAPPING SCREW 2.0*6 (BLACK) 2 *1
12 EHHS95LPSTW LOCK PLATE SPRING 1
13 EHHS95PSW PIVOT SPRING 1
14 EHHS95SLPBW SLIDE LOCK PLATE 1
15 EHHS95SHBW SHAFT 1
16 EHHS95PPBW PRESS PLATE 1
17 EHHS95HBBW HEATER B ASSEMBLY BLOCK 1
18 EHHS952060SW TAPPING SCREW 2.0*6 (SILVER) 1
19 EHHS95HVCW MOISTURE HV CIRCUIT ASSEMBLY BLOCK 1 (INCLUDE 1 ALUMINUM SEAL)
20 EHHS95PPC41W PRESS PLATE COVER 1 (FOR INDONESIA)
20 EHHS95PPC61W PRESS PLATE COVER 1 NO PRINTED "nanocare"
20 EHHS95PPC62W PRESS PLATE COVER 1 PRINTED "nanocare"
20 EHHS95PPC67W PRESS PLATE COVER 1 (FOR KOREA)
21 EHHS95CBW CLEANING BRUSH 1
- EHHS9567S03W OPERATING INSTRUCTIONS 1 (FOR KOREA)
- EHHS9568S03W OPERATING INSTRUCTIONS 1 (FOR ASIA)
- EHHS95S415KW INDIVIDUAL PACKAGE 1 (FOR EH-HS95-K415)
- EHHS95S615KW INDIVIDUAL PACKAGE 1 (FOR EH-HS95-K615)
- EHHS95S62KW INDIVIDUAL PACKAGE 1 (FOR EH-HS95-K62 : INDIA)
- EHHS95S655KW INDIVIDUAL PACKAGE 1 (FOR EH-HS95-K655)
- EHHS95S665KW INDIVIDUAL PACKAGE 1 (FOR EH-HS95-K665)
- EHHS95S675KW INDIVIDUAL PACKAGE 1 (FOR EH-HS95-K675)
- EHHS95S685KW INDIVIDUAL PACKAGE 1 (FOR EH-HS95-K685)
- EHHS95S695KW INDIVIDUAL PACKAGE 1 (FOR EH-HS95-K695)
- EHHS95S09W PULP FILLER 1