Panasonic nanoe EH-HS99 User manual

Order Number PEWT1711M40CE
Model No.
EH-HS99
TABLE OF CONTENTS
PAGE
1 Warning --------------------------------------------------------------------
2
2 Specifications -------------------------------------------------------
2
3 Troubleshooting Guide ----------------------------------------------
3
4 Disassembly and Assembly instructions --------------------------
5
5 Wiring Connection Diagram -----------------------------------------
8
6 Schematic Diagram -----------------------------------------------
9
7 Explode View and Replacement Part List -------------------------------
10
(Household) Hair Straightener
Middle East
© Panasonic Corporation 2013 Unauthorized copying
and distribution is a violation of law.

1. Warning
Caution:
- Pb free solder has a higher melting point that standard solder typically the melting point
is 50 - 70°F (30 - 40°C) a higher. Please use soldering iron with temperature control
and adjust it to 700±20°F (370 ± 10°C).
In case of using high temperature soldering iron, please be careful not to heat too long.
- Pb free solder will tend to splash when heated too high (about 1100°F / 600℃).
Model
Sales Area
Power source / AC 100-120V ~ 50-60Hz
Power consumption AC 220-240V ~ 50-60Hz
Iron Plate temperature 150-170-180-200-230℃(5 level settings)
Body size (mm.)
Weight
Cord length
2. Specifications
1.7m
EH-HS99
Middle East
38.0W (Max.41.8W)
S3 Plug (SF629)
450g
286×33×44
S3 Plug (SF629)

3.TROUBLESHOOTING GUIDE
Refer to WIRING CONNECTION DIAGRAM.
Before insert the POWER CORD to CONNECTOR COVER ASSEMBLY,
must check if the terminal inside the CONNECTOR COVER ASSEMBLY is deformed.
< CHECKING PROCEDURE >
< CHECKING METHOD >
< REMEDY >
Check the
POWER CORD
Check the conductivity of
POWER CORD
Check the
HEATER A ASSEMBLY
Check if the Resistance value
between lead wire Purple and Black
is 29-34Ω
Check the Switch button
(Power switch and Temp.
adjust switch)
Check the operation of Switch button
(Power switch and Temp. adjust
switch) on HOUSING B.
(Check if it works smoothly)
NG
OK
Temp. adjust switch
(Micro) PCB
Power switch
LED (Temp. level lamp)
150
170
180
200
230
Current Fuse
No operation.
- LED does not light
- Iron plate does not become hot
- Nano-e does not generate
Replace the
POWER CORD
Re-assembly or replace
the Switch button
Replace the
HEATER A SSEMBLY
Check the
HEATER B ASSEMBLY
Check if the Resistance value
between lead wire Yellow and Gray
is 29-34Ω
Check (Micro) PCB Press the Tag switch on (Micro) PCB
and check if the LED lights. Replace the
HEATER A ASSEMBLY
Replace the
HEATER B ASSEMBLY
NG
NG
NG
NG
OK
OK
OK
Terminal
Power cord

< CHECKING PROCEDURE >
< CHECKING METHOD >
< REMEDY >
Check if the Resistance value
between lead wire Purple and Black
is 29-34Ω
NG
OK
(Micro) PCB
Temp. adjust switch
Power switch
LED (Temp. level lamp)
Current Fuse
150
170
180 200
230
LED does not light
Replace the
HEATER A ASSEMBLY
Cheak the
HEATER B ASSEMBLY
Check if the Resistance value
between lead wire Yellow and Gray
is 29-34Ω
Check (Micro) PCB Press the Tag switch on (Micro) PCB
and check if the LED lights. Replace the
HEATER A ASSEMBLY
Replace the
HEATER B ASSEMBLY
NG
NG
Replace the
HEATER A ASSEMBLY
Iron plate (Heater) does not
become hot but LED lights.
Cheak the
HEATER A ASSEMBLY
Temp. does not change when
press the Temp. adjust switch
Check the Switch button
(Power switch and
Temp. adjust switch)
Check the operation of Switch button
(Power switch and Temp. adjust
switch) on HOUSING B.
(Check if it works smoothly)
Re-assembly or replace
the Switch button
NG
OK
Nano-e does not generate
Clean the Nano-e hole
Replace the
HEATER B ASSEMBLY
Check the working condition of Nano-e
(check If it has abnormal noise at Nano-e hole)
OK
NG

4. Disassembly and Assembly instructions
4.1 Disassembly instruction
(1) Remove SHAFT COVER from Main body (4) Remove PIVOT SPRING by gripping
by slotted screw driver (Minus driver). and pull it out from the Main body.
NOTE: Use NEW SHAFT COVER once disassembling
due to easily breakage or looseness of hook.
(2) Remove TORX SCREW at SHAFT position
by screw driver (Star driver).
(5) Remove TAPPING SCREWS at PRESS PLATE COVER
by screw driver (Plus driver) and pull out
PRESS PLATE COVER from Main body.
(3) Remove SHAFT out by tiny-shaped screw driver
and pull it out from Main body
(6) Take off (HV) PCB from hook of PRESS PLATE 3 positions.
Minus driver
Shaft cover
Hook
Torx screw
Shaft
Tiny-shaped screw driver
Pivot spring
Tapping screws
Tapping screws Tapping screws
Tapping screws
Press plate cover
Hook
Hook
(HV) PCB
Heater B

(7) Remove SLIDE LOCK PLATE from Main Body (9) Take off (Micro) PCB from hook of HOUSING A
by slotted screw driver (Minus driver) 2 positions.
*Insert screw driver to hook inside SLIDE LOCK PLATE.
(10) Remove soldering point for taking off
lead wire 6 positions (Red, Blue, White, Gray,
Yelow, Brown) from (Micro) PCB.
(8) Remove TAPPING SCREWS at HOUSING B
by screw driver (Plus driver) and pull out
HOUSING B from Main body.
(10) Remove soldering point at Lead wire Red
and Blue for taking off CONNECTOR COVER ASSEMBLY
* Be careful not to lose the Floating SPRING 4 pcs on HOUSING A
Hook Slide Lock Plate
Minus driver
Floating springs
Housing A
Tapping screws (Big size)
Tapping screws (Big size)
Tapping screws (Small size)
Hook (Micro) PCB
Blue Red White
Gray Yellow Brown
Red
Blue
Soldering point
Connector cover assembly

4.2 Assembly Instructions
(1) Assembly point of HOUSING A (2) SHAFT fixing point. Have control direction.
Check the POWER CORD must be correctly assembled
with CONNECTOR COVER ASSEMBLY
*Apply a little of Grease Floil to Terminal of
POWER CORD.
(3) SHAFT COVER fixing point. Have control direction.
4.3 Lead wire of HEATER B ASSEMBLY and Circuit arrangement points.
(1) Assembled HEATER B ASSEMBLY with PRESS PLATE by arrangement Lead wire as figure 1.
and must insert all Lead wires pass through the Tube before soldering.
Figure 1.
(2) Assembled HEATER A ASSEMBLY with HOUSING A by arrangement Lead wire as figure 2.
and must insert all Lead wires pass through the Tube before soldering.
Figure 2.
Power cord
Connector cover assembly
Control position of Press plate side
Control position
of Shaft cover
Control position of Press Plate side
Control position
of Shaft
White
Brown
Blue
White
Red
Orange
Gray
Yellow
Heater B assembly
Gray
Black
Purple
Red
Blue White Red
Blue
Yellow Brown
Rib
Rib
Rib
Rib
Tube
Tube
Heater A assembly

4.3 Check list after assembly
Apply voltage to Main body and press the Power Switch, The Main body must be follow below items.
(1) LED Lights
(2) Both Iron Plate become hot.
(3) Ion is generated effectively
(4) Able to lock.
5.Wiring Connection Diagram
Iron plate (Heater A side)
Iron plate (Heater B side)
Moisture assembly block
Yellow
(TH+)
Yellow
(TH-) Red
(NANO)
Blue
(IPD) White
(AC2-2)
Black
(HA-) Red
(AC2)
Blue
(AC1)
Brown
(AC1-2)
Yellow
(HA+)
Purple
(HB-)
Gray
(HT)
Orange
(N_GND) White
(AC2-2)
HV
Red
(NANO) Blue (IPD)
Brown
(AC1-2)
Black

6. Schematic Diagram

7. EXPLODED VIEW & REPLACEMENT PARTS LIST
7.1. Exploded View
All parts are supplied from PMFTH-AP through PLAP