Panasonic KX-TS2300HGW User manual

PLEASE READ BEFORE USE AND SAVE.
Contents:
Location of Controls . . . . . . . . . . . . . . . . 3
Settings . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connecting a Communication Device. . . 5
Making/Answering Calls . . . . . . . . . . . . . 6
One-Touch Dialer. . . . . . . . . . . . . . . . . . 7
RECALL Button . . . . . . . . . . . . . . . . . . . 8
Temporary Tone Dialing
(For Rotary or Pulse Service Users). . . . 8
Wall Mounting. . . . . . . . . . . . . . . . . . . . . 9
Safety Instructions . . . . . . . . . . . . . . . . 10
Integrated Telephone System
Model No. KX-TS2300HGW
Pulse-or-tone dialing capability
Operating Instructions

– 2 –
Thank you for purchasing your new Panasonic cordless
telephone.
For your future reference
Serial No. Date of purchase
(found on the bottom of the unit)
Name and address of dealer

– 3 –
Location of Controls
ABC
DEF
JKL MNO
GHI
TUV WXYZ
PQRS
PAUSE
REDIAL
RECALL
PROGRAM
INTEGRATED TELEPHONE SYSTEM
50
TONE
AUTO
M1 M2 M3
1
2
3
4
6
1
7
8
9
(TONE) Button
(RECALL) Button
RINGER Selector
(PROGRAM) Button
(PAUSE) Button
(REDIAL) Button
One-Touch Auto Dial
Buttons
(AUTO) Button Ringer Indicator
HANDSET VOLUME
Selector
DIALING MODE
Selector

– 4 –
Settings
To Single-Line
Telephone Jack
Handset Cord
Handset
Telephone Line
Cord
LINE DATA
1Connect the handset cord.
2Connect the telephone line cord, then lift the handset to confirm the dial tone.
3Set the DIALING MODE selector to TONE.
≥If you cannot dial, set to PULSE.
4Set the RINGER selector to HIGH, LOW or OFF.
≥When set to OFF, the unit will not ring.
5Set the HANDSET VOLUME selector to HIGH, MEDIUM or LOW.
HIGH
RINGER
OFF LOW
TONE
DIALING
MODE
PULSE
HIGH
HANDSET
VOLUME
LOW

– 5 –
Connecting a Communication Device
≥Make sure the communication device is not in use before using this unit
(making calls, storing phone numbers in memory etc.) or the communication
device may not operate properly.
≥Computer
≥Modem
≥Fax
≥Answering machine
To Single-Line
Telephone Jack
LINE DATA

– 6 –
∫Making Calls
1Lift the handset.
2Dial a phone number.
≥If you misdial, hang up and start from step 1.
3When finished talking, hang up.
≥To redial the last number: Lift the handset, then press (REDIAL).
∫Answering Calls
1When the unit rings, lift the handset.
2When finished talking, hang up.
Making/Answering Calls

– 7 –
One-Touch Dialer
You can store up to 3 phone numbers in the one-touch auto dial buttons ((M1) to
(M3)).
Do not press any one-touch auto dial buttons before storing to prevent
misoperation.
∫To store a number
1Lift the handset.
2Press (PROGRAM).
3Enter a phone number up to 16 digits.
≥If you enter a wrong number, hang up and start again from step 1.
4Press (PROGRAM).
5Press one of a one-touch auto dial button ((M1) to (M3)).
6When finished, hang up.
≥To store other numbers, repeat steps 1 through 5.
∫To dial a stored number
1Lift the handset.
2Press the one-touch auto dial button ((M1) to (M3)).
≥The stored number is dialed.

– 8 –
RECALL Button
Pressing (RECALL) allows you to use special features of your host PBX such as
transferring an extension call or accessing special telephone services (optional)
such as call waiting.
Temporary Tone Dialing (For Rotary or Pulse Service Users)
Press (TONE) before entering access numbers which require tone dialing.
≥The dialing mode changes to tone. You can enter numbers to access
answering services, electronic banking services, etc. When you hang up, the
mode returns to pulse

– 9 –
Wall Mounting
This unit can be mounted on a wall.
1Pull down the handset hook until it locks, so the tab holds the handset.
To temporarily set the handset
down during a conversation,
place it as shown here.
Wall Template
8.3 cm
Screws
8.3 cm
To Single-Line
Telephone Jack
3Install screws using the wall template below. Connect the telephone line cord.
Mount the unit, and slide down.
2Tuck the telephone line cord inside the wall mounting adaptor, and push it in the
direction of the arrow.
≥“UP” should be facing upward.

– 10 –
Safety Instructions
Take special care to follow the safety suggestions listed below.
Installations
Environment
1) Do not use this unit near water—for example, near a bathtub, washbowl,
sink, etc. Damp basements should also be avoided.
2) The unit should be kept away from heat sources such as radiators, kitchen
range, etc. It also should not be placed in rooms where the temperature is
less than 5oC or greater than 40oC.
Placement
1) Do not place heavy objects on top of this unit.
2) Care should be taken so that objects do not fall onto, and liquids are not
spilled into, the unit. Do not subject this unit to excessive smoke, dust,
mechanical vibration or shock.
3) Place the unit on a flat surface.
Lightning surge
This unit has already been equipped with a built-in lightning protection circuit.
However, we recommend that you install lightning protection on the telephone
line, if your area has a high incidence of lightning strikes.
To install the above option, please contact your local sales shop.
≥Lightning damage is not covered in the warranty even if lightning protection is
installed.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR ANY TYPE OF MOISTURE.
If there is any trouble, disconnect the unit from the telephone line and connect a
known working phone. If the known working phone operates properly, do not
reconnect the unit to the telephone line until the trouble has been repaired. If
the known working phone does not operate properly, consult your telephone
company.