Panasonic KX-TD816RU User manual

Digital Super Hybrid System
KX-TD816RU
KX-TD1232RU
Added and Changed Features for
Installation Manual and Programming Tables
Vol. 2
Please read this manual first and then the Installation Manual.
In this manual, the last letter “RU” or “CE”of each model number is omitted.
ROM Version : KX-TD816RU — P371A/P372A; KX-TD1232RU — P271A/P272A;
and later versions

2
Table of Contents
Additions to KX-TD816/1232
Section 1.4, Options
16 SLT Line Circuit Unit (KX-TD174)...............................................................................6
Auxiliary Connection for Power Failure Transfer...............................................................7
ISDN 6-S0 Line Unit (KX-TD286).....................................................................................7
Section 2.4, Installation of Optional Cards and Units
16 SLT Circuit Line Connection .........................................................................................8
Installing Expansion Unit (KX-TD174)..............................................................................8
Cable Pin Numbers to Be Connected..................................................................................9
Installing Expansion Unit (KX-TD286)..............................................................................10
ISDN 6-S0 Line Unit Connection ......................................................................................10
Internal ISDN S0 Line Connection.....................................................................................12
Section 3, Features
ISDN Extension ..................................................................................................................14
Section 4, System Programming
[012] ISDN Extension Number Set....................................................................................16
[013] ISDN Extension Name Set .......................................................................................18
[014] Budget Management on ISDN Port..........................................................................19
[424] ISDN Port Type ........................................................................................................20
[425] ISDN Layer 1 Active Mode......................................................................................21
[426] ISDN Configuration..................................................................................................22
[427] ISDN Data Line Mode..............................................................................................23
[428] ISDN TEI Mode .......................................................................................................24
[429] ISDN Extension Multiple Subscriber Number.........................................................25
[430] ISDN Extension Progress Tone ................................................................................26
[612] Incoming Call Display..............................................................................................27
[613] ISDN Class of Service ..............................................................................................28
[614-615] Outgoing Permitted CO Line Assignment– Day/Night for ISDN Extension ...29
Changes
Section 3, Features
Module Expansion...............................................................................................................32, 33
Section 4, System Programming
[105] Account Codes..........................................................................................................32
[991] COS Additional Information.....................................................................................32
Programming Tables for Added and Changed Features
[012] ISDN Extension Number Set....................................................................................36
[013] ISDN Extension Name Set .......................................................................................36
[014] Budget Management on ISDN Port..........................................................................36
[105] Account Codes..........................................................................................................37
[424] ISDN Port Type ........................................................................................................39
[425] ISDN Layer 1 Active Mode......................................................................................39
[426] ISDN Configuration..................................................................................................39
[427] ISDN Data Line Mode..............................................................................................39

3
Table of Contents
[428] ISDN TEI Mode .......................................................................................................40
[429] ISDN Extension Multiple Subscriber Number.........................................................40
[430] ISDN Extension Progress Tone ................................................................................40
[612] Incoming Call Display..............................................................................................41
[613] ISDN Class of Service ..............................................................................................41
[614] Outgoing Permitted CO Line Assignment– Day for ISDN Extension.....................42
[615] Outgoing Permitted CO Line Assignment– Night for ISDN Extension...................43

Additions to KX-TD816/1232

6
1.4 Options
16 or 32 single line
telephones can be
added.
D1232D1232
DIGITAL SUPER HYBRID SYSTEM
Panasonic
16 SLT Line Circuit Unit (KX-TD174)
Each unit adds eight extensions which contain two single line
telephones. The unit can support 16 single line telephones per unit.
One unit for the KX-TD816 and up to two units for the KX-TD1232
can be installed per system.
Each single line telephone in the same jack has different extension
number so that it can act as completely different extension like an
eXtra Device Port feature.
Note:
• Installing this unit allows the eXtra Device Port setting to “Enable” automatically in system
programming [600]. However, assigning “Disable” makes a single line telephone which is
connected to the second jack (Jack xx-2) disable to use.
• This unit cannot support the proprietary telephone and Voice Mail Integration features.
• This unit has four DTMF receivers; two receivers in the first eight ports and two receivers in
the last eight ports.
• The Ringing Patterns for all single line telephones which are connected to the system are
changed as below;
1S 1S
Incoming call from outside line Incoming call from extension
Panasonic
Panasonic
D816D816
DIGITAL SUPER HYBRID SYSTEM
16 single line
telephones can be
added.

7
1.4 Options
One KX-TD286 can be installed per system.
ISDN 6-S0 Line Unit (KX-TD286)
D1232D1232
DIGITAL SUPER HYBRID SYSTEM
Panasonic
Panasonic
6 ISDN S0 lines can
be added.
Note
Either one KX-TD280, one KX-TD286 or one KX-TD180 can be installed in a system.
6 ISDN S0 lines
can be added.
Panasonic
Panasonic
D816D816
DIGITAL SUPER HYBRID SYSTEM
Auxiliary Connection for Power Failure Transfer
When there is a power failure, the first two jacks on this unit can be
connected to specific CO lines mentioned below. An auxiliary
connection is required to implement this feature. For more
information about the connection between an extension jack to a
CO line, refer to the “2.5 Auxiliary Connection for Power Failure
Transfer” in the main Installation Manual.
KX-TD816 Jack 09-1...CO 5
Jack 10-1...CO 6
KX-TD1232 Jack 17-1...CO 9
Jack 18-1...CO10

8
16 SLT Circuit Line Connection
Installing one unit to the system allows 16 single line telephones
(SLT’s) to be connected to jacks 09 through 16 for the KX-TD816,
or jacks 17 through 24 or jacks 25 through 32 for the KX-TD1232.
Installing two units allows 32 SLT’s to be connected to jacks 17
through 32 for the KX-TD1232.
This unit can be installed to any of the expansion areas provided on
the front of the system.
For unit installation, refer to the procedure “Section 2.4.4
“Installing Expansion Unit (KX-TD170/KX-TD180)” in the main
Installation Manual. Steps 1 through 5 and 7 through 10 of the
installation procedure are the same as the other expansion units.
Step 6 is different for each unit. Please note the following
instructions below instead of step 6 (Installation Manual) for this
unit.
Note • System Programming [109] Expansion Unit Type is required for the
expansion unit location identification.
Installing Expansion Unit (KX-TD174)
Step 6
■ If the KX-TD174 is installed, use an Amphenol Connector to connect extensions.
Insert the connector into the jack.
Panasonic
PFTports
Connector typeConnector type
50-pin (Amphenol 57JE
series or the equivalent)
25
50
1
26
To 4-CO Line Unit KX-TD180
(Jack for Power Failure Transfer†)
KX-TD816 : Jacks 09 - 16
KX-TD1232 : Jacks 17 - 24 or 25 - 32
To extensions
2.4 Installation of Optional Cards and Units

9
Cable Pin Numbers to Be Connected
CONN.
PIN
Clip
Terminal
(KX-A205)
No.
26
1
27
2
1
2
3
4
For KX-TD816
Jack No. 9-16
For KX-TD1232
(Expansion 1)
Jack No.17-24
For KX-TD1232
(Expansion 2)
Jack No. 25-32
Jack. 09 - 1
Jack. 10 - 1
Jack. 17 - 1
Jack. 18 - 1
Jack. 25 - 1
Jack. 26 - 1
Jack. 11 - 1
Jack. 12 - 1
Jack. 19 - 1
Jack. 20 - 1
Jack. 27 - 1
Jack. 28 - 1
Jack. 13 - 1
Jack. 14 - 1
Jack. 21 - 1
Jack. 22 - 1
Jack. 29 - 1
Jack. 30 - 1
Jack. 15 - 1
Jack. 16 - 1
Jack. 23 - 1
Jack. 24 - 1
Jack. 31 - 1
Jack. 32 - 1
Jack. 09 - 2
Jack. 10 - 2
Jack. 17 - 2
Jack. 18 - 2
Jack. 25 - 2
Jack. 26 - 2
Jack. 11 - 2
Jack. 12 - 2
Jack. 19 - 2
Jack. 20 - 2
Jack. 27 - 2
Jack. 28 - 2
Jack. 13 - 2
Jack. 14 - 2
Jack. 21 - 2
Jack. 22 - 2
Jack. 29 - 2
Jack. 30 - 2
Jack. 15 - 2
Jack. 16 - 2
Jack. 23 - 2
Jack. 24 - 2
Jack. 31 - 2
Jack. 32 - 2
T
R
T
R
T
R
T
R
T
R
T
R
28
3
29
4
5
6
7
8
T
R
T
R
T
R
T
R
T
R
T
R
30
5
31
6
9
10
11
12
T
R
T
R
T
R
T
R
T
R
T
R
32
7
33
8
13
14
15
16
T
R
T
R
T
R
T
R
T
R
T
R
34
9
35
10
17
18
19
20
T
R
T
R
T
R
T
R
T
R
T
R
36
11
37
12
21
22
23
24
T
R
T
R
T
R
T
R
T
R
T
R
38
13
39
14
25
26
27
28
T
R
T
R
T
R
T
R
T
R
T
R
40
15
41
16
29
30
31
32
T
R
T
R
T
R
T
R
T
R
T
R
Installing Expansion Unit (KX-TD174)
Note:
• To fix the connector, refer to “Section 2.4.4 “Installing Expansion Unit (KX-TD170/KX-TD180),
Amphenol 57 Type (screw-attach-type 50-pin connector) Connection for KX-TD170” in the main
Installation Manual.
• For jack connection, please see “Cable Pin Numbers to Be Connected” on the next page.
• †For more information, see “Auxiliary Connection for Power Failure Transfer” in this leaflet.
• The KX-TD1232 is illustrated above.

10
Installing Expansion Unit (KX-TD286)
ISDN 6-S0 Line Unit Connection
To add six ISDN S0 lines, use the optional ISDN 6-S0 Line Unit
(KX-TD286). This unit can be installed in any of the expansion
areas provided on the front of the main unit.
When the KX-TD286 is installed in the KX-TD816, only four
ISDN S0 lines are available for outside lines and the other ports are
for extension lines (ISDN extensions).
System programming is required for unit location identification.
Default KX-TD816: bottom = 4-CO Line Unit,
top = 8-Station Line Unit
KX-TD1232: bottom = 4-CO Line Unit,
middle and top = 8-Station Line Unit

11
To Terminal Board or Modular
Jacks from the Central Office
7. Insert the plug into a jack on the unit.
Connect an earth wire to the earth terminal
on the extension expansion unit.
KX-TD286
Panasonic
Jack
no.
S01
S02
S03
S04
S05
S06
TB
TA
RA
RB
RB
RA
TA
TB
for internal
ISDN S0
line
Note • All ports can be either for CO line or
extension line.
Installing Expansion Unit (KX-TD286)
6. Prepare the required plugs. Six 4-pin
plugs are included in KX-TD286 to
connect CO lines or ISDN terminal
equipment.
For unit installation, refer to the procedure “Installing Expansion
Unit (KX-TD280)” in the main Added and Changed Features for
Installation Manual and Programming Tables Vol. 1. Steps 1
through 5 and 8 through 11 of the installation procedure are the
same as the KX-TD280. Step 6 and Step 7 are different from those
of KX-TD280. Please note the following instructions below
instead of step 6 and step 7 for this unit.
Note • System Programming [109] Expansion Unit Type is required for the
expansion unit location identification.

12
Internal ISDN S0 Line Connection
The ISDN S0 Bus on the KX-TD280 and the KX-TD286 can be
used as internal S0 bus. Each port can be used as either external or
internal ISDN S0 Lines. Some System Programs are required to
use the S0 bus as internal ISDN S0 lines beforehand.
Connection Use 4-pin plugs (included) to connect ISDN S0 lines. A single plug
is able to connect one ISDN S0 line. Mis-connection may cause the
system to operate improperly.
1. Re-arrange telephone wires in reverse order of the plug.
2. Insert the plug into a ISDN S0 port on the unit.
TB
TA
RA
RB
RB
RA
TA
TB
Wiring for external ISDN S0 line Wiring for internal ISDN S0 line
Panasonic
Jack
no.
S01
S02
S03
S04
S05
S06
TB
TA
RA
RB
RB
RA
TA
TB
For
internal
ISDN S0
line
Notes For installing the KX-TD280 or KX-TD286 to main unit, refer to
“Installing Expansion Unit” respectably.
3. Connect the lines between the ISDN board and the ISDN device.
4. Plug the AC power cord into the system and an AC outlet.
5. Program “[424] ISDN Port Type” and other required programs
in System Programming.
6. Press the Reset Button with a pointed tool on the main unit.
Panasonic
PFTports
2COw/PFT
2CO
ISDN
Port No.1
ISDN
Port No.2
TB
TA
RA
RB
RB
RA
TA
TB
For internal
ISDN S0 line
KX-TD280 KX-TD286

13
D1232D1232
DIGITAL SUPER HYBRID SYSTEM
PanasonicPanasonic
Internal ISDN S0 Line Connection
Maximum cabling distance of S0 bus connection
The maximum length of the extension line cord that connects the
main unit and the ISDN terminal equipment (TE) is shown below:
Wiring with Terminating Resistors (TR)
The ISDN S0 bus should be terminated with two100Ωterminating
resistors (TR).
Power Supply for ISDN Terminal Equipment (TE)
The system does not provide a power supply to terminal equipment
(TE). Depending on the type of TE's, the external power supply is
required on ISDN S0 line to operate.
Under 1000 m
TE
Under 150 m
Under 500 m Under 50 m
TE 1 TE 8
TE 1 TE 8
Point-to-Point
Expansion Point-to-Multipoint
Point-to-Multipoint
Main
Unit
TE 1 TE 8 †TR
RB
RA
TA
TB
TR 100Ω
TR 100Ω
TR†

14
I3 Features
ISDN Extension
Description The system supports terminal equipments with separate power
supplies. For example, ISDN telephone, G4 Facsimile and
personal computers which are connected to optional ISDN S0 Line
Unit : KX-TD280 or KX-TD286. A maximum of eight terminal
equipments can be connected to each ISDN S0 bus with point-to-
multi-point configuration. Terminal equipments can be addressed
individually with Multiple Subscriber Numbers (MSN). The MSN
consists of the ISDN extension number and an additional digit, 0
through 9. If MSN is not assigned, all equipments on the same S0
bus are called simultaneously.
The following bearer capabilities can be supported:
Transfer Mode Transfer Capability
Circuit Unrestricted digital
Circuit Speech
Circuit 3.1 kHz Audio
The functions of terminal equipment are similar to single line
telephone functions, but the following features are not available.
• Automatic Callback Busy • Conference
• Call Forwarding • Do Not Disturb
• Call Hold • Log-In / Log-Out
• Call Park • Message Waiting
• Call Pickup • Paging – Group Answer
• Call Transfer • Pickup Dialing
• Call Waiting • Timed Reminder
Conditions • Class of Service for ISDN extension port applies to all terminal
equipments on the same S0 bus.
• Each port can be assigned as follows:
*1 and *2: can be either an external or internal ISDN S0 line.
*1: when assigned as internal, the corresponding analog CO ports
become available. TD1232
ISDN
Port
1
2
3
4
5
6
TD280
—
—
—
—
*2
*2
TD286
*1
*1
*1
*1
*2
*2
CO
No.
1, 2
3, 4
5, 6
7, 8
9, 10
11, 12
ISDN
Port
1
2
3
4
5
6
TD280
—
—
*2
*2
—
—
TD286
*1
*1
*2
*2
Internal
Internal
TD816
CO
No.
1, 2
3, 4
5, 6
7, 8
—
—

15
3 Features I
Connection References Section 2, Installation — in this manual
Internal ISDN S0 Line Connection
Programming References
Section 4, System Programming,
[012] ISDN Extension Number Set — in this manual
[013] ISDN Extension Name Set — in this manual
[014] Budget Management on ISDN Port — in this manual
[109] Expansion Unit Type — Vol. 1
[424] ISDN Port Type — in this manual
[425] ISDN Layer 1 Active Mode — in this manual
[426] ISDN Configuration — in this manual
[427] ISDN Data Link Mode — in this manual
[428] ISDN TEI Mode — in this manual
[429] ISDN Extension Multiple Subscriber Number — in this manual
[430] ISDN Extension Progress Tone — in this manual
[613] ISDN Class of Service — in this manual
[614-615] Outgoing Permitted CO Line Assignment – Day/Night for
ISDN Extension — in this manual
• The possible parameter combinations are listed below. The underlined
selections are recommended. The selections marked "*" are activated,
regardless of the assignments.
Feature References None
Operation References None
Program
Parameter
[424] ISDN
Port Type
CO
Extension
[425] ISDN
Layer 1 Active
Mode
Permanent
—
Call/
Permanent
Call/
Permanent
[426] ISDN
Configuration
P–P
P–M
(not available)
P–P
P–M
[427] ISDN
Data Link
Mode
Permanent
—
Call/
Permanent
Call*
[428] ISDN
TEI Mode
Fix 0-63
Automatic
—
Fix 0-63*
Automatic*

4.2 Manager Programming
ISDN Extension Number Set
16
012
Description Assigns an extension number to each port which is connected to the
ISDN S0 unit or card.
Selection • Port number: KX-TD816—01 through 06
KX-TD1232—01 through 12
• Extension Number: 2 or 3 digits
Default All ports – Not stored
Programming 1. Enter 012.
Display: ISDN EXT NO.
2. Press NEXT.
Display: Port NO?–>
3. Enter a port number.
To enter a first port number, you can also press NEXT.
Display: #01:Not Stored
4. Enter an extension number.
To change the current entry, press CLEAR and the new number.
5. Press STORE.
6. To program another port, press NEXT or PREV, or SELECT
and the desired port number.
7. Repeat steps 4 through 6.
8. Press END.
Conditions • Each extension number can be two or three digits, consisting of 0
through 9. The and # keys cannot be used.
• A multiple subscriber number (MSN) is determined regarding this
assignment. The MSN consists of the assigned extension number and an
additional digit, 0 through 9.
Example) In case that the ISDN extension number is assigned “3”;
30 through 39 are effective as MSN's. The extension user can call any
terminal equipment on the ISDN S0 bus with MSN individually.
Pressing “30” calls all extensions on the ISDN S0 bus simultaneously.
• Port numbers 01 through 06 are for the Master System and 07 through
12 are for the Slave, if available.

4.2 Manager Programming
ISDN Extension Number Set (contd.)
012
17
• An extension number is invalid if the leading first or second digits
disagree with the setting of the program [100] “Flexible Numbering, 1st
through 16th hundred extension blocks.” If one digit is assigned as the
leading digit, some extensions have two digits and some have three
digits. If two digits are assigned, some have three digits and some have
four digits.
• Double entry or incompatible entry is invalid including the assignment
of program [813] “Floating Number Assignment.” Valid entry
examples: 10 and 11; 10 and 110. Invalid entry examples: 10 and 106;
210 and 21.
• Program [013] “ISDN Extension Name Set” is used to give names to
the extension numbers.
Feature References None

4.2 Manager Programming
ISDN Extension Name Set
18
013
Description Assigns names to the ISDN extension numbers programmed in
program [012] “ISDN Extension Number Set.”
Selection • Port number: KX-TD816—01 through 06
KX-TD1232—01 through 12
• Name: 10 characters (max.)
Default All ports – Not stored
Programming 1. Enter 013.
Display: ISDN EXT. Name.
2. Press NEXT.
Display: Port NO?–>
3. Enter a port number.
To enter a first port number, you can also press NEXT.
Display: #01:Not Stored
4. Enter a name.
For entering characters, see Section 4.1.3 “Entering Characters.”
To delete the current entry, press CLEAR.
To change the current entry, press CLEAR and the new name.
5. Press STORE.
6. To program another port, press NEXT or PREV, or
SELECT and the desired port number.
7. Repeat steps 4 through 6.
8. Press END.
Conditions • Port numbers 01 through 06 are for the Master System and 07 through
12 are for the Slave, if available.
Feature References None

4.2 Manager Programming
Budget Management on ISDN Port 014
19
Description Assigns the charge limitation of a call on the ISDN extension port
basis.
Selection • Port number: KX-TD816—01 through 06,
KX-TD1232—01 through 12,
( =all ports)
• Charge limitation (Charge): 0 through 59999
Default All ports – 0
Programming 1. Enter 014.
Display: ISDN Charge Lim.
2. Press NEXT.
Display: Port NO?–>
3. Enter a port number.
To enter a first port number, you can also press NEXT.
Display example: #01: 0
4. Enter a charge limitation.
To delete the charge limitation, press CLEAR.
5. Press STORE.
6. To program another port, press NEXT or PREV, or
SELECT and the desired port number.
7. Repeat steps 4 through 6.
8. Press END.
Conditions • If the charge limitation is set “0,” no restriction is applied.
• To assign all port to one selection, press the key at step 3.
In this case, the display shows the contents programmed for a first port.
• Port numbers 01 through 06 are for the Master System and 07 through
12 are for the Slave, if available.
• The displayed currency denomination can be programmed by [121]
Assignment of Denomination.
Feature References Section 3, Features,
Budget management — in this manual
Charge Fee Reference — in this manual

4.6 CO Line Programming
ISDN Port Type
424
20
Description Assigns the type of each port either CO line or extension line on
ISDN port basis.
Selection • Port number: KX-TD816—01 through 04, ( =all ports)
KX-TD1232—01 through 12, ( =all ports)
•CO (CO line) / Extension
Default All ports – CO
Programming 1. Enter 424.
Display: ISDN Line Type
2. Press NEXT.
Display: Port NO?–>
3. Enter a port number.
To enter a first port number, you can also press NEXT.
Display example: #01:CO
4. Keep pressing SELECT until the desired selection is
displayed.
5. Press STORE.
6. To program another port, press NEXT or PREV, or
SELECT and the desired port number.
7. Repeat steps 4 through 6.
8. Press END.
Conditions • For the KX-TD816, port numbers 05 and 06 are fixed as “Extension.”
• For the KX-TD1232, port numbers 01 through 06 are for the Master
System and 07 through 12 are for the Slave, if available.
• To assign all ports to one selection, press the key at step 3. In this
case, the display shows the contents programmed for a first port.
• After this assignment, you should reset the system so that this
assignment is effective.
Feature References None