ParaBody 950 st User manual

SeriousSteel
950 ST
ASSEMBLY INSTRUCTIONS
Pa.rt# 6639601 R~vision:10/10/96

***IMPORTANT***
¯THE pARABODY 950 ST MUSTBE ASSEMBLEDON A FLAT, LEVEL SURFACE TO ASSURE ITS PROPER
FUNCTION.
PARABODYINC. STRONGLYRECOMMENDSTHAT THIS PRODUCT BE ASSEMBLED B~( TWO PERSONS TO
AVOID" POSSIBLE INJURY.
¯KEEP ALL FRAME CONNECTIONS LOOSE, UNTIL INSTRUCTED IN THE ASSEMBLY STEP SEQUENCES TO
SECURELYTIGHTEN. ~
¯IF YOU EXPERIENCE ~IY PROBLEMWITH THE ASSEMBLY OF THIS PRODUCT, PLEASE CONTACTYOUR
DEALER OR YOURPARABODYCUSTOMERSERVICE REPRESENTATIVE AT: 1-800-328-9’714
¯TOOLSREQUIRED,:RATCHET, 3/4 SOCKETor WRENCH,9/16 SOCKET or WRENCH,7/16 SOCKETor
WRENCH,ADJUSTABI,E WRENCH,1/8 ALLEN WRENCH,5/32 ALLEN WRENCH,7/32 ALLEN WRENCH,LEVEL,
and RUBBER MALLETor HAMMER
2

TTENTION. !!
IliA ~
(1) B O L I; TWO(2) ~ WASHERS.AN_D__ONE
-- LOCKNUT
NOTE: BOLT LENGTH IS MEASUREDFROMTHE UNDERSIDE OF THE HEAD OF THE BOLT.
,1,3///ii!!1
BOLT LENGTH
BOLT LENGTH RULER:
1234 [ I I I

950 STPacts List
KEY} PART# DFSCRIPTION
II 6623603 PRESS WT STACK BASEWHT
2 I 6624202 BACK’ PAl) ANGLE LEFTBLK
3..I 662’4302 BACK PADANGLFRIGHTBLK
4I 6622903 PECARM RIGHTWHT
5I 6623003 PECARM LEFTWHT
6t 6’623503 PRESSAR/Vl WHT
" ~ I 6624502 CALF/LOW RQW8LK
8I 662460,3 LEG CURL/EXTWHT
" ~ } 6625203 LEG CURL HANDLEWHT
.10 I ’6~25303 REAR LEG BASEWHT
11 I 6625402 LEG BACK PADADJBLK
12 662550~ LEG BACK PADSUPTBLK
13 6624703 PRESSBASEWHT
14 6625003 !LEG FRAMEWHT
15 6617903 ’BASEWHT
16 6621001 LATBAR CHROM~
17 6623903 PRESS FRAMEWHT
’18 6824803 LEG WEIGHT STACK BASEWHT
19 ~~- . ROLLERPAD PU 3/41D X 4ODX 6-1/2
20 6616703 TOP BOOMWHT
"2’1 6617103 REAR UPRIGHTWHT’
22 6822503 BEARING HOUSINGWHT
23 6623403 PRESS ARM ADJUSTBLK
24 6621503 PRESS GUIDE ROD suPPORT WHT
’"25 6621603 LEG GUIDE ROD SUPPORTWHT
.....26 61’10502 BRKT’0 3-1/2X 1-1/2X 1 BLK
27 6485301 ROLLERPAD SHAFT, 15-3/4 IN.
"28 6523401 GUIDE’ROD
29 6529702 PECCAM BLK
30 6594702 F~’OATING PULLEY BLK
31 6617303 FRONTUPRIGHT’V~’HT
32 6620903 FLOATING PULLEY STOP WHT
33 6623303 ;SEAT sUPPORTWHT
34 6624903 ROLLER PAD Ar~JUSTER WHT
35 6625103 LEGEXTHANDLEWHT
36 662~903 CENTER PULLEYBRKTWHT
37 6628302 PLATE1’18 X 2 X 8 BLK
38 66231’52 PAD’SUPPORTBLK
’:~9 6623702 WOLFFSLEEVE’ BLK
40 6623803 PRESS SUPPORT TUBE WHT
41 6624402 SWIVEL PULLEY BRKT BLK
42 6634901 ROLLERPAD SHAFT, 18-’I14
~,3 662i203 PEC GUIDE Ror~ SUPPORT Writ
44 66371XX PAD ASSEMBLY, 22X 10-1/2
45 66186XX PAD ASSEMBLY, 13-1/2X 10-1/2T
46 66377XX P~DASSEMBLY, 16X6
47 66370XX PAD ASSEMBLY, ]5-3/4 X 15-1/2 T
48 66373Xx PAD ASSEMBLY, 22X 10-1/2
49 66353XX iPADASSEMBLY, 13-1/2X 1"0-1/2T
50 66363XX ~I~A’D ASSEMBLY,33-1/2 X 10-1/2
51 6533301 ;SHROUDASSY950PECSTAO;ION
52 6636101 SHROUDASSY’ 950 LEGS~ATION
53 6636201 SHROUDASSY’" 950 PRESSSTATION
54 3105401 STARLOCK’3’I4
¯ ~5 3108901 WASHER PLASTIC2ODX.’~551D
56 I 31i6’001 BUMPERRUBBER I-I/4SQ
’ ~7 I 3117401 CAPPLUG#6X
58 ! 3118401’ (~AP VINY~7/’I61D’X4
59 I 3202401 iCAPSCREW BTNHEAD3/8~I6X’1
6’0} 6140701 IGLIDE lXl , , ii
I QTY
1
1
1
1
I
I
I
2
2
2
6
14
2
6
17
4
KEY I PART #
61 i 6117700
"62 i 6412O01
DE~CRi TION
79I 31025o2
BO I 3102506
’STRIP NON-SKID2-1)2 X 5-1/2
ASSYSPRING PIN 3/8
63 ! 6416601 GLIDE 1-1/2X3/4UHilWPEQTY8
64 I 6466901 ASSY SPRING PIN i/~DIA
65 ! ~103801 LINK SNAP B/16DIA
66 .~ 3104901 BEARING FLG3/41DX 1
67I 6214501 WEIGHT PLATE
68 } 3109602 NUT PAL 1121D
69 I 6020601 BE’ARING FLG 1/21DX 5/8OD
70 ’i 6075906 CHAIN 12LINK ’
71 ,{ 6166701 BRKT L2-71BX 1 X 1
72 I 6214’401 PIN V/EIGHT STACKSE.ECTOR
73 ! 6406401 HINGE TAB 3/16X 1-1 X6
74 I 6480301 SPACERFLANGE3/8 II ,XS/8OD
75 I 6533501 BRKT L2-3/BX 1 X 1
76 6618901 AXLE 3/4DIAX2"9/~-;
7~ , 6619501 BEARING SLVO/41DX 1-1/8OD
78 I 3102501 WASHERFLAT 3/81D
WASHERFLAT 1/2 ID
;WASHERFLAT 1(41D
81 3102803 NUTNYLOCK1/4-28
3102801 NUT NYLOCK1/2-13
83 j 3102802 NUT NYLOCK3/8-16
84.I 3102804 NUT NYLOCKl/2-i3LOWHT
85 3106803
86 3114502
87 3102~10
88 I 3102917
89
t 5~o2918
SET SCREWCPT5/16. 8X3/8
WAS’HER"LOCK318 ID BZ
BOLT HHG2 1/2-13X
BOL’[: HHG2 1/2-i3x4
BOLT HHG21/2-i3 X 3..1/4
90 I, 3102937 BOLT HHG21/2-13X4.,112
91 I3102943 BOLT HHG21/2-13X3,,112
92 I, 3102949 BOLT HHG21/2-13X5 /2
93 I3102954 BOLTHHG21/2-13 X7..1/2
94 ! 6639601 950 ST ASSEMBLYINS’f’RUCTIONS
95 I3102904 BOLT HHG2 3/8-16X
96 I3102905 BOLT HHG23/8-16X3
97 t3102909 ~BOLT HHG23/8-16X1
8
1
2
3
4
28
3
1
2
, 69
47
2
2
23
39
6
2
5
5
4
’6
’4
6
’1
1
1
98 I 3102916 BOLT HHG2 3/8-16X3 /4
99 I 3102922 BOLT HHG23/8-161~’2 ~/4
1001 310293’3 BOLT HHG2 3/8-16X2
101 I 6375801 STRAP ABCRUNCH
1021 6382301 ASSY PLATE BUSHING OCT
1031 6409101 STRAP ANKLESTAND~,RD
104I I6535601 CABLEASSYBE-BE 77..
105 I 6627~,0i CABL~EASSYWS-NBSI! 221-1/4
1061 6627501
107l 6627601
08J 6627701
091 3108002
1101 3116101
1111 311620i
1121 3202301
113l 6284501
114l 638970i
1151 6619301
1161 6626201
117!.6628401
11816183501
119} 3102902
120i 6122704
CABLE ASSYT-NB’SE 61-3/4
CABLE ASSY WS-NBS:" 273-1/2
CABLE ASSY WS-NB S 169
CUSHION WEIGHT STA, 3/4 ID
PULLEY 4-1/20DXO/81DX 1
PULLEY 3-1/200X3181DX 1
BEARING PILLOW BLO~: 1 ID
SHAFT SELECT 3/4 DIA 20 HOLE
BAR LOW ROWCH~O’M
PIN U 1/2 OlA X 6-1/8’~ 3-7/8
SHAFT 3i4 DIA X 10-1/:
PTD ASSY HEAD PLATE BLK
1
:WEIGHT STACK LABELS ] 3
BOLT HHG23/8-16X2. /4 I 1
ISPACER,318 ID X 5I~()[ X 1/4 J 1

Frame Assembly Instructions
Use t’his procedure to ossemble the frame of the PareBody 950ST
Step 1
A. Loosely assemble the leg wei.~,ht stack bose (18) a.n,,d the press weight s~ack base (1) to the
(15) using two 1/2 x .3-1/2 bolts (91), four 1/2 washers (79), and two 1/2" nylock nuts (B2)
~ho~n. Apply two non-skid s~rips (61) fo the base as shown.
B. Loosely assemble the front uprig~ (31) to the base (15) using two 1/2 x 3-1/2" bolts (91),
1/2’ washers (79), and two 1/2 nylock nuts (82) as shown. 3" /2"
C. Loosely ~ssembe the re~r ~,prighf (21) fo the b~se (15) using one li2 x bolt (87),
w~shers (79), ~nd one 1/2 nyock nul (82) ~s shown.
ssembl: the fop boom (20) ~o fh~ front upright (31) using one 1/2 x 3" bolt (BT),
D. Log~ly a, ,’;~ --- --- ~/2" nvlock nut {82), and to the rear uprigh~ (~1) using two 1/2 x
1/Z wesners k~~},_~, u~ ~’~ "~-_.. ~.~ ~/~,, low height nylock nut ~84) ~s shown. Tighten
~1 frame connections. 5

Step 2
A. Securely assemblethe floating pulley stop (:52), and the s.eat support (33) to the front upright
using two 1/2 x 4.-1/2" bolts (90), four 1/2’ washers (.79), and two 1/2" nylock nuts (B2).
B. Apply eight 1-1/2 x 3/4" glides (63) to the inside surface of the seat support (32;) as shown.
C. Securely assemble one 3/8" spring pin (62) to the seat support (33) os shown.
1"
D. Securely attach one, seat pad (45) fo the pad support (38) using two 3/8 x bolts (97), and
3/8" washers (78) as shown.
E. Securely attach one; back pad (44) to the front upright (31) using two 3/8 x 3--3/4" bolts (96),
two 3/8" washers (78).
F. Attach two roller pads (19) to the front upright (51) using one 18-1/4" roller pad shaft (42),
=" d3/4" sfarlock collars (54) as shown.
plastic washers (5.~) an two 6

Step 3
A. Securely assemble the bearing housl.n,g (22) and the center, pulley bracket (36) to fine front
upright (31) using two 1/2 x 4-1/2’ bolts (90), four 1/2’ washers (79), and two 1/2" nylock
(82). (Note: Push bearing housing up as high as possible before tightening.)
B. Assemble the right, pee arm ,I4) and one pec cam (29) to the bearing housing (22) using
sleeve bearlng (77), two 3/4 flange bearings (66), one 1/2" washer (79), and ona 1/2" nylock
(82). (Note: Securely tighten, then back nut off 1/4 turn to allow the pec arm to rotate freely.)
C. Assemble the left pec arm (5) and one pec cam (29) to the bearing housing (22) using 3/4"
sleeve bearing (77), two 3/4" flange bearings (66), 1/2" washer (79), and on e 1/ 2" n ylock
nut (B2). (Note: Securely tighten, then back nut off 1/4 turn to allow the pec arm to rotate freely.)
D. Securely assemble one 3/8" spring pin (62) to both the right pec arm (4) and the left pec arm
as shown.
1" (60) to the bearing housing (22) where the pec cams (2!))
E. Apply two 1" x glides
contact with the bearing housing as shown.
F. Securely attach one pec arm pad (46) to both the right pec arm (4) and left pec arm (5)
four3/8 ×2-3/,~"bo~ts(99) andfour3/8"washers(78).
7

Siep4 /2"
A. Securely attach fh~, press base (13) fo the base (15) using two 1/2 x 3-1/4" bolts (89),
washers (79) ,~nd two 1/.2".nylock nuts .(8,2), and fo the rear upright (21) using one 3/8 x 3"
(95), two 3/8’ washers (,78) and one 3/8’ nylock
B. Securely assemble one :~/B" spring pin (62) to the wolff sleeve (39) as shown.
C. Aftc~ch one u-pin (115) to the wolff sleeve (39) using one 1/2" pal nut (68). Slide vinyl
cap (58) onto the u-pin as shown.
D. Cc~refully slide assembled wolff sleeve (39) onto the press frc~me (17) until the spring pin engages
in one of the holes.

Step 5 , nLJt (1~2), and two 3/8"
I
3’ bolts (95), two 1/2’ washers , 2’1
nylock nufs (831. (Note: Make

Slap 8
A. Slide two hinge tabs (73) onto the wolff sleeve (39) and securely attach press seat pad (49)
The "hinge" part of the hinge tab
1"
two 3/B x bolts (97), and two 3/B" washers (7B). (Note:
should face upward.)
B. Slide the right back pad angle (2) and left back pad angle (3) onto the wolff sleeve (39)
1"
attach the press back pad (50) using four 3/8 bol{s (97), and four 3/8" ~rashers (TB).
C. Insert one 3/4 x 10-1/2" shaft (116) into the press base (13) as shown.
E. Secure the press support tubes (40))~],ght back pad angle (2)and the left back pod angle
two 1/2" nylock nuts (82).
using two 1/2 x bolts (87), four flange bearings (69), and
Secure nuts, then back off 1/4 turn.)
F. Center 3/4 x 10-1/2" shaft (116) and secure press suppoH tubes (40) using two 5/16 x 3/B"
screws
G. Apply one rubber bumber (56) to the back of the press back pad (50) where the pad comes
contact with the rear bolt. 10

Step 7
A. Loosely aftachthe pressarm odiu.s,, ~ (23) to the rear up.r,!gh~(21) using two 1" pillow block
bearings (112), four 3/8 x 3-1/4 bolts (98), four 3/B’ washers (78), and
B. Center press arm adiust (23) to I~ne up w~th ~he post on the press base (13) and securely ~ighlen
set screws on the pillow block bearings (112).
C. Adiusl pillow block bearings (112) until the press arm ad[us~ (23) is level and securely tighten
bolls.
D. Securely assemble one 1/2" spring pln (64) to the press arm (6) as shown.
s~u~=.=~ ~e p~e.. ~=~) ~o ~.~ p~’" =~=~iu~ (~) "’~ o~~/~ ~ ~-~/2" bo~(~),
~wo 1/2" washers (79), ~wo 1 flange bearings (69), a,nd one 1/2" low height nylock
(Note: Securely tighten, then back nut off 1/4 turn to allow the press arm to rofcffe freely.)
r. s~u~.~y=,~h~,~/~o~ro~(7) ~o~h~p~.,, b=~(~3) u,~ng~o~/2~ ~"bo~,(~8), four
~o the
/z"
washers (79), and two low height nylock nuts (84). Apply ~wo non-skid z~frips (61)
calf / low row a~s shown.
G. AHach swivel pulley bracket (41) fo the press base (13) using one 1/2" low height nylock
(84). (Note: Securely tighten, ~hen back nu~ off 1/4 turn fo allow the swivel pulley bracket fo rotate
freely.)
11

Step B
A. Securely attoch the rear leg base (10) ond the leg curl hondle (9) *o the leg frame (14) using
1/2 ×3-1/4"bolts(Bg),t~.o.~/8 ×3-1/4".bolts(98), tour1/2"washers(79), ~o,~r~/B"washers
(TB), *wo 1/2" nylock nuts (,B2), and two 3/B" nylock nuts (,B3).
Securely attach two leg extension hand!es .(~5) fo the leg frame (14) using *wo 3/8 x 3-1/4 bolts
(9B), four 3/B" washers (78),
Securely assemble one 1/2" spring pin (64) *o *he leg frame (14) as shown.
Securely ~H~ch on~,,1/B x 2 x plate (37) fo ~he leg se~ p~d (47)

STEP 9-B
STEP 9
A. Slide fwlo,, hinge tabs (73) onto the leg frame (14) and securely ah~ach leg seat pad (47) using
3/8 x bolts (97), and two 3/B" washers (78). (Note: The "hinge" part of the ’hinge tab should
face downward.)
B. Attach two roller peels (19) to the leg frame (14) using one 15-3/4" roller pad shc, ff (27),
plastic washers (55) and two 3/4" starlock collars (54) as shown
SE"ENOT ’
STEP 10
A. Attach leg back pad adjust (11), and leg back pad support (12) to the leg frame (14)
one 1/2 x 5-1/2" bolt (92), two 1/2" flange bearings (69) and one 1/2" low he,ighf lock
back nut off 1/4 turn to allow the two F,ar~s to
as shown. (Note: ~.ecurely tighten, then
rotate freely.)
B. Securely attach the leg back pad (48) to the leg back pad adjust (11), and leg bc~ck pad
support (12), using four 3/8 x 2-3/4’.’ bolts (99) and four 3/8" washers (78).
C. Securely attach leg curl/extension (8) to the leg frame (~14) using two 3/4" flange bearings
(S6), one 3/4" tapped axle (76), two 3/8" black lock washers (86), and two 3/8 x 1" black
button head cap screws (59).
~OTE: BOTH CAP :S~S M~T ~ TIGHT~D AT THE ~ T~E ~I~ TVO ~LEN V~~
D. Securely attach rubber bumper (56) between :ontac~ point o~ leg curl/extenslon(8) ~nd
frome (14) as shown. I$

STEP1 1
A.
gEE])ETA,IL
Securely assemble two 3/8" spring pins (62) to the leg curl/extension (8) as shown.
B. Apply eight 1-1/2 x 3/4" glides (63) to the outside surfaces of each roller .pad adiuster (34)
shown, and insert roller pad adjusters (34) into the leg curl/extension (B). (.Note: The end caps
will needto be temporarily removed.) ,
C. Securely assemble leg frame (14) to the leg weight slack base (18) using two x 3- 1/4" bolt s
(89), four 1/2" washers (79), and two 1/2 nylock nuts (B2).
D. Attach. ,f, our roller pads(19) to the leg curl/extension (8) and roller padadjusters (’34) using two
15-3/4 roller pad shafts (27), eight plastic washers (55) and four 3/4" starlock ,iollars (54) as
¯- 14

SEE NOTE
Step 1 2
A. Insert two plate bushings (102) into the "ParaBody" side of each of sixty weight plates (67)
shown.
B. Insert one guide rod (28) through one weight stack cushion (109) and into each ef the large
holes in the base (15), the leg weight stack base (18), and the press weight stack press (1) as
C. Carefully slide twenty weight plates (67) onto each set of guide rods (28) wlfh the "ParaBody"
side up and the center key-hole facing outward.
D. Securely assembe one selector,shaft (113) to one head plate (117) using one 5/8" block
washer (86), and .one 3/8 x 1’ black button head cap screw (59). Repeat this step for the other two
head plates. (NOTE: THE BOLT HOLE IN THE HEAD PLATE SHOULDBE ON TOP)
E. Carefully slide one head plate assembly over each set of guide rods and onto each top weight
plate as shown.
F. Insert one cap plug (57) into each guide rod (28).
G. Apply one weight ~sfock label (118) onto each weight plate (67) as shown. Lc~bels 1 through
should be applied from top to bottom of the weight stock and close to f~’,e key-hole.
.-,
15

Step 1 3
A. Slide peo guide rod support ~4~,), onto ~he eo we]aht slack guide rods and loosely :ff~ach it
fo the boom using tiwo 3/B bolts.(95), four 3/8" washers (781, and two 3/8 nylock
nuts (831¯ (Note: This connection will be secured in a la’ter step offer ~he pulleys
are assembled.)
rods and securely Qssemble them fo lhe boom using two 1/2. x 3-1 bolls (91), four
washers (79), and t:wo 1/2" nylock nuts (82).
"" 16

CABLE GUIDE
’
PEC DEC%
" CABLE
STAMPEDPARTNUMBER
65356
//
77 5/8"
STAMPED
66274-
//
PARTNUMBER
AB CRUNCH~
I. ,]
STAMPEDPARTNUMBER
66275
’ //
61 3/4"
LEG PRESS~Xx
CABLE
STAMPEDPARTNUMBER
66276
//
¯ £73 7/8"
STAMPEDPARTNUMBER
66277
169"
"17

Pec Dec Cable Assembly Instructions
Use this procedure to assemble ~he pec dec cables of the Pc~raBody 950ST
Step C
Step F & H
LAT
CABLE
Stel3 1 order, route the threaded end of the lot coble (~403~! through the top boom (20), the boise
A. ~r~5~h, iSen d the Icrge hole in the pec guide rod support
B. Screw the threaded end of the lat cable (107) approximately 5/4" into the end of t’he selector
shaft (113) and tighten jam nut securely as shown.
C. Securely assemble three 3-1/2" pulleys (111)_i~o the slots of ~he fop boom (20) using three
2-3/4" bolls (99), six 3/8" Flmnge Spacers ~14), ~nd three 3/8" nylock nu~s (83). (Note: Loop
cable ~round each pulley prior to inseffing if into the slob)
D. Securely ~ssemble ~wo 3-1/2" pulleys (111) lnfo the slots of the base (15) using two 3/8
2-3/4" bolls (99), four 3/8" Flonge Spacers (74), and two 3/8" nylock nuts (8~{). (Note: Loop
cable around e~ch pulley prior ~o inseffing if into the slot.)
E. securely lighten ~he bolts of the pec 9uide rod support (43) ~nd fop boom (20) connection ~f
time. (Note: Center the pec guide rod suppo~ horizontally end vertically before tightening.
F. Apply two 1" x 1" glides (SO) to the flo~fing pulley (30), ~s shown.
G. Securey assemble,one 4-1/2" pulle~ (110) ~o ~he flo~ting pulley stop (~2) using one 3/8 x 2-3/4"
bolt (99), two 3/8’ flange spacers (74), and one 3/8" nylock nu~ (B3).
H. Securely assemble one 4-1/2" pulley (110),~o the flo~fing pulley (30) using 3,/8 x 2" bolt
(100), ~wo 3/8" w,=shers (78), and one 3/8 nylock nut (83). Loop cable around pulley and
flo~fing pulley (30) onto the flo~fing pulley stop (32).
"’ 18

Step 2
A. Conneot one end of the pec deo cable (104) to the slotted bushing on the right peo oam
(29). Route the other end of the pec dec cable around the front upright (31) and connect
to the slotted bushing on the left pec cam (29).
B. Securely assemble the pec dec cable (104) and tWO 4-1/2" pulleys (110) to the c-=nter
pulley bracket (36) uslng..t,,wo 3/8 x 2" b. olfs (100), two 2-7/8" ’L’ brackets (71), four
washers (78) and two 3/8 nylock nuts (.83). (Note: The pec dee cable should be routed
underneath the shorl leg of the ’L’ bracket. Also the ’L’ brackets should be positioned af a 45
degree angle to function properly.)
"19

\ \
Step 3
A. Securely assemble l,~he ’U’ bracket (~26) fo the threaded end of the ab crunch c~ble (106) using
two 1/4" washers ~80) and two 1/4" nylock nuts (B1). (Note: Position the ’U’ br’ackef in ~he middle
of the thread as shown and "lock’-nuts together.)
B. Securely assemble ~he pec dec cpble (104) agd .one 3-I/2" pulley (111) ~o the ’U’ bracket (26)
one 3/8 x 2" bolt (I00), lwo 3/8" washers (78), and ,one 378" nylock nut (83). (Note: Loop
cable around the pulley prior to inse~ingif into the ’U brackel.)