Paradox NV37MX User manual

PARADOX.COM
NV37MX
Installation Manual V1.0 BETA
Outdoor/Indoor Window and Sliding Door
Dual Detector with Anti-Masking and Pet
Immunity
General Description
Thank you for choosing the NV37MX for your professional protection
needs. The NV37MX EVO version will provide you the most advanced
window and sliding door protection either in Pet Immune or Sharp
mode, while programming can be done remotely via EVO bus
connection. If you have any comments please write to us at
Paradox.com/products/feedback.
Pet Recommended Installation (please read)
The NV37MX has been designed to be installed within the frame of
windows and doors when installed outdoors. Make sure that the unit is
not directly exposed to rain; this will ensure the best performance
against false alarms when random pets such as birds, cats and small
dogs access the window sill. Other installation methods can be used
with the NV37MX such as wall beam protection but if installed outside
of the frame its pet immunity may be compromised.
Installing the NV37MX
1. Remove the NV37MX front cover - open the Captive screw.
2. Remove the Main Unit: open the two snap-lock mechanisms on
each side of the back cover attaching the Main Unit to the back
cover as displayed below. Then remove the Main Unit.
3. Pull the wires from the control panel through the knockout holes
and mount the back cover onto the window frame or wall using
screws.
Note: PLEASE KEEP AT LEAST 4 cm / 1.5 in. clearance from
window/shutter.
4. Attach the Main Unit to the back cover - ensure the locks snap
closed.
5. Connect the wires to the terminal blocks according to the following
wiring assignment.
Table 1: Wiring Assignment
6. Replace the front cover and close the Captive screw.
Note: PLEASE KEEP AT LEAST 4 cm / 1.5 in. clearance from
window/shutter.
Do not obscure the detector's field of view.
Programming the NV37MX via Keypad or
BabyWare
Via Keypad
1. Enter EVO Installer Programming Mode, programming section 4003.
2. Enter the detector’s 8-digit Serial Number. Enter the 3-digit
Section as per Table 2.
Table 2
Section [001]:
Table 3
Section [002]:
Section [003]: 00 (Low), 01 (Medium), 02 (High)
Via BabyWare
1. Double-click the serial number of the NV37MX to open the
detector’s programming.
2. Configure the required settings.
Testing the NV37MX
Perform a Walk-Test to test successful installation: Walk slowly across
the far end of the detection range. Ensure detection.
Walk test mode lasts 5 minutes after the tamper screw is closed.
Figure 1 – Removing the
Front Cover
Figure 2 – Main
Unit
Figure 3 – Back Plate
Front
cover
Captive screw
Mounting
screw
Tam pe r
knockout
hole
Knockout
holes
Tam pe r
screw
An optional mounting bracket for the NV37MX is available for
ordering, part number: SB35.
4 cm /
1.5 in.
Terminal Connector Recommended Wiring Assignment
Bus Label Wire Color
1 12V+ Red
2 Minus (-) Black
3Data Green
4Clock Yellow
Bit Function Status/Description
[1] LED Display Alarm ON: Enabled (default) OFF: Disabled
[3] LED Display Trouble ON: Enabled (default) OFF: Disabled
[5] Anti-mask ON: Enabled (default) OFF: Disabled
[6] Anti-mask Sensitivity ON: High (default) OFF: Low
Bit Function Status/Description
[1] Unit Tamper ON: Enabled (default), OFF: Disabled
[2] Wall Tamper ON: Enabled (default), OFF: Disabled
[3] PET Immunity ON: Enabled (default) (PET Mode)
OFF: Disabled (SHARP Mode)

PARADOX.COM
Beam Pattern
PET Mode
SHARP Mode
Top View
LED Display
Technical Specifications
SIDE VIEW:
0.5m
1m
1.5m
5m1m 2m 3m 4m 6m 7m 8m 9m 10m
(32.8ft)
2m
(6.5ft)
0m
0m
Feature LED Status Indicator
Tamper open Green: ON for 0.3 seconds every 30 seconds
PIR sensitivity level
setting
Green: Flashes 1-3 times according to the
selected level
Alarm detection Red: ON for 2 seconds
Booting/Tamper close Green/Red alternating flashes for 30 seconds
Anti-mask detection Flashing Orange:
Pre-mask situation is detected.
Orange LED flashes ON/OFF 3 times.
Solid Orange:
Real mask is detected (can take between 20
-150 seconds after the pre-mask situation).
Orange LED will remain solid “ON” while
mask is present.
Model Number NV37MX
Infrared Sensor type 2 Dual elements
Detection range • PET Immunity mode: 7.5m x 2m (25 x 7 ft)
•Sharp mode: 10 x 2m (33 x 7 ft)
Super Pet Immunity Pet size approximately 50cm
Anti- mask Active IR detection for blocking 30cm and
sprayed liquid
Input voltage 10 to 15 VDC
Current consumption Typical: 15mA
Maximum: 19.2mA
Compatibility EVO systems
Outdoor protection IP54
Operation
temperature
-35°C to +50°C
Relative humidity 95% non-condensing
Dimensions 12.3 x 6.1 x 4.3 cm (4.8 x 2.4 x 1.7 in.)
Certifications CE, EN50131-2-2 Grade 3, Class IV
Weight 100g / 0.2 lb
Warranty
For complete warranty information on this product, please refer to the Limited Warranty Statement found on the website:
www.paradox.com/terms or contact your local distributor. Specifications may change without prior notice.
Patents
US, Canadian and international patents may apply. Paradox is a trademark or registered trademark of Paradox Security Systems
(Bahamas) Ltd.