Parker Compax3 Fluid T40 User manual

RGB ELEKTRONIKA AGACIAK CIACIEK
SPÓŁKA JAWNA
Jana Dlugosza 2-6 Street
51-162 Wrocław
Poland
[e-mail]
[phone]
www.rgbautomatyka.pl
www.rgbelektronika.pl
DATASHEET
www.rgbautomatyka.pl
www.rgbelektronika.pl
OTHER SYMBOLS:
C3S025V2F12 I20 T11 M00
PARKER HANNIFIN

YOUR
PARTNER IN
MAINTENANCE
At our premises in Wrocław, we have a fully equipped servicing facility. Here we perform all the repair
works and test each later sold unit. Our trained employees, equipped with a wide variety of tools and
having several testing stands at their disposal, are a guarantee of the highest quality service.
OUR SERVICES
ENCODERS
SERVO
DRIVERS
LINEAR
ENCODERS
SERVO AMPLIFIERS
CNC
MACHINES
MOTORS
POWER
SUPPLIERS
OPERATOR
PANELS
CNC
CONTROLS
INDUSTRIAL
COMPUTERS
PLC
SYSTEMS
Repair this product with RGB ELEKTRONIKA ORDER A DIAGNOSIS ∠
Buy this product at RGB AUTOMATYKA BUY ∠

Com
pax
3 Electromechanical Automation
We reserve the right to make technical changes. 27.12.10 15:01 192-120113 N08 C3I12T11 - December 2010
The data correspond to the current status at the time of printing.
Operating instructions Compax3 I12T11
Positioning via digital I/Os & Com port
192-120113 N08 C3I12T11
December 2010
Release R09-10

Introduction C3I12T11
2
192-120113 N08 C3I12T11 - December 2010
____________________________
Windows NT®, Windows 2000™, Windows XP™, Windows Vista are trademarks
of Microsoft Corporation.
nonwarranty clause
We checked the contents of this publication for compliance with the associated
hard and software. We can, however, not exclude discrepancies and do therefore
not accept any liability for the exact compliance. The information in this publication
is regularly checked, necessary corrections will be part of the subsequent
publications.
Worldwide sales
http://divapps.parker.com/divapps/eme/EME/Contact_sites/Sales%20Channel
_Parker-EME.pdf
Production site:
Parker Hannifin GmbH
Electromechanical Automation Europe [EME]
Robert-Bosch-Strasse 22
77656 Offenburg (Germany)
Tel.: + 49 (0781) 509-0
Fax: + 49 (0781) 509-98176
Internet: www.parker-eme.com http://www.parker-eme.com
E-mail: [e-mail] mailto:sales.automa[email protected]
Parker Hannifin GmbH - registered office: Bielefeld HRB 35489
Geschäftsführung: Dr. Gerd Scheffel, Günter Schrank, Christian Stein, Kees Veraart - Aufsichtsratsvorsitzender: Hansgeorg Greuner
Headquarters:
Parker Hannifin PLC • Electromechanical Automation • Arena Business Centre
Holy Rood Close • Poole, Dorset BH17 7FJ UK
Tel.: [phone] • Fax: [phone]
E-mail: [e-mail] mailto:sales.automa[email protected] •
Internet: www.parker-eme.com http://www.parker-eme.com
Parker Hannifin S.p.A • SSD SBC • Electromechanical Automation • Via Gounod, 1
I-20092 Cinisello Balsamo (MI), Italy
Tel.: [phone] • Fax: [phone]
E-mail: [e-mail] mailto:[e-mail] •
Internet: www.parker-eme.com http://www.parker-eme.com
Parker Hannifin Corporation • Electromechanical Automation
5500 Business Park Drive • Rohnert Park, CA 94928
Phone #: [phone] • FAX #: [phone]
E-mail: [e-mail] mailto:emn_[email protected]om • Internet:
www.compumotor.com http://www.compumotor.com
England:
Italy:
USA:

Parker EME Introduction
192-120113 N08 C3I12T11 - December 2010
3
Inhalt
1. Introduction ...........................................................................................11
1.1 Device assignment ................................................................................ 11
1.2 Scope of delivery................................................................................... 12
1.3 Type specification plate ........................................................................ 13
1.4 Packaging, transport, storage .............................................................. 14
1.5 Safety instructions................................................................................. 16
1.5.1. General hazards............................................................................................... 16
1.5.2. Safety-conscious working.............................................................................. 16
1.5.3. Special safety instructions ............................................................................. 17
1.6 Warranty conditions .............................................................................. 18
1.7 Conditions of utilization........................................................................ 19
1.7.1. Conditions of utilization for CE-conform operation..................................... 19
1.7.1.1 Conditions of utilization mains filter ...................................................... 19
1.7.1.2 Conditions of utilization for cables / motor filter.................................... 20
1.7.1.3 Additional conditions of utilization......................................................... 21
1.7.2. Conditions of utilization for UL certification Compax3S............................. 22
1.7.3. Conditions of utilization for UL certification Compax3M ............................ 23
1.7.4. Conditions of utilization for UL certification Compax3H............................. 24
1.7.5. Current on the mains PE (leakage current)................................................... 25
1.7.6. Supply networks.............................................................................................. 25
2. C3I12T11 Function overview ................................................................26
3. Compax3 device description................................................................28
3.1 Meaning of the status LEDs - Compax3 axis controller ..................... 28
3.2 Meaning of the status LEDs - PSUP (mains module).......................... 29
3.3 Connections of Compax3S ................................................................... 30
3.3.1. Compax3S connectors.................................................................................... 30
3.3.2. Connector and pin assignment C3S.............................................................. 31
3.3.3. Control voltage 24VDC / enable connector X4 C3S ..................................... 33
3.3.4. Motor / Motor brake (C3S connector X3)....................................................... 34
3.3.5. Compax3Sxxx V2............................................................................................. 35
3.3.5.1 Main voltage supply C3S connector X1................................................ 35
3.3.5.2 Braking resistor / high voltage DC C3S connector X2.......................... 36
3.3.6. Compax3Sxxx V4............................................................................................. 38
3.3.6.1 Power supply connector X1 for 3AC 400VAC/480VAC-C3S
devices.................................................................................................. 38
3.3.6.2 Braking resistor / high voltage supply connector X2 for 3AC
400VAC/480VAC_C3S devices............................................................ 39
3.3.6.3 Connection of the power voltage of 2 C3S 3AC devices...................... 39

Introduction C3I12T11
4
192-120113 N08 C3I12T11 - December 2010
3.4 Installation instructions Compax3M .................................................... 40
3.5 PSUP/Compax3M Connections ............................................................ 42
3.5.1. Front connector ............................................................................................... 42
3.5.2. Connections on the device bottom................................................................ 43
3.5.3. Connections of the axis combination............................................................ 44
3.5.4. Control voltage 24VDC PSUP (mains module)............................................. 45
3.5.5. Mains supply PSUP (mains module) X41...................................................... 46
3.5.6. Braking resistor / temperature switch PSUP (mains module) .................... 48
3.5.6.1 Temperature switch PSUP (mains module).......................................... 50
3.5.7. Motor / motor brake Compax3M (axis controller) ........................................ 50
3.5.7.1 Measurement of the motor temperature of Compax3M (axis
controller).............................................................................................. 51
3.5.8. Safety technology option for Compax3M (axis controller) ......................... 51
3.6 Connections of Compax3H................................................................... 52
3.6.1. Compax3H plugs/connections....................................................................... 52
3.6.2. Connection of the power voltage................................................................... 53
3.6.3. Compax3H connections front plate............................................................... 55
3.6.4. Plug and pin assignment C3H........................................................................ 55
3.6.5. Motor / Motor brake C3H................................................................................. 57
3.6.6. Control voltage 24 VDC C3H........................................................................... 58
3.6.7. Mains connection Compax3H......................................................................... 58
3.6.8. Braking resistor / supply voltage C3H........................................................... 59
3.6.8.1 Connect braking resistor C3H............................................................... 59
3.6.8.2 Power supply voltage DC C3H ............................................................. 59
3.6.8.3 Connection of the power voltage of 2 C3H 3AC devices...................... 60
3.7 Communication interfaces.................................................................... 61
3.7.1. RS232/RS485 interface (plug X10) ................................................................. 61
3.7.2. Communication Compax3M ........................................................................... 62
3.7.2.1 PC - PSUP (Mains module).................................................................. 62
3.7.2.2 Communication in the axis combination (connector X30, X31)............ 62
3.7.2.3 Adjusting the basic address.................................................................. 63
3.7.2.4 Setting the axis function........................................................................ 63
3.8 Signal interfaces .................................................................................... 64
3.8.1. Resolver / feedback (plug X13) ...................................................................... 64
3.8.2. Analogue / encoder (plug X11)....................................................................... 65
3.8.2.1 Wiring of analog interfaces ................................................................... 65
3.8.2.2 Connections of the encoder interface................................................... 65
3.8.3. Digital inputs/outputs (plug X12) ................................................................... 66
3.8.3.1 Connection of the digital Outputs/Inputs............................................... 67
3.8.3.2 Logic proximity switch types ................................................................. 67
3.9 Installation and dimensions Compax3................................................. 68
3.9.1. Mounting and dimensions Compax3S .......................................................... 68
3.9.1.1 Mounting and dimensions Compax3S0xxV2........................................ 68
3.9.1.2 Mounting and dimensions Compax3S100V2 and S0xxV4................... 69
3.9.1.3 Mounting and dimensions Compax3S150V2 and S150V4................... 70
3.9.1.4 Mounting and dimensions Compax3S300V4........................................ 71
3.9.2. Mounting and dimensions PSUP/C3M........................................................... 72
3.9.2.1 Mounting and dimensions PSUP10/C3M050D6, C3M100D6,
C3M150D6............................................................................................ 72
3.9.2.2 Mounting and dimensions PSUP20/PSUP30/C3M300D6.................... 73

Parker EME Introduction
192-120113 N08 C3I12T11 - December 2010
5
3.9.2.3 With upper mounting, the housing design may be different ................. 73
3.9.3. Mounting and dimensions C3H...................................................................... 74
3.9.3.1 Mounting distances, air currents Compax3H050V4 ............................. 75
3.9.3.2 Mounting distances, air currents Compax3H090V4 ............................. 75
3.9.3.3 Mounting distances, air currents Compax3H1xxV4.............................. 76
3.10 Safety function - STO (=safe torque off) .............................................. 77
3.10.1. General Description......................................................................................... 77
3.10.1.1 Important terms and explanations ........................................................ 77
3.10.1.2 Intended use ......................................................................................... 78
3.10.1.3 Advantages of using the "safe torque off" safety function.................... 78
3.10.1.4 Devices with the STO (=safe torque off) safety function ...................... 79
3.10.2. STO (= safe torque off) with Compax3S........................................................ 80
3.10.2.1 STO Principle (= Safe Torque Off) with Compax3S............................. 80
3.10.2.2 Conditions of utilization STO (=safe torque off) Safety function........... 82
3.10.2.3 Notes on the STO function.................................................................... 82
3.10.2.4 STO application example (= safe torque off)........................................ 84
3.10.2.5 Technical Characteristics STO Compax3S .......................................... 87
3.10.3. STO (= safe torque off) with Compax3m (Option S1)................................... 88
3.10.3.1 Safety switching circuits........................................................................ 88
3.10.3.2 Safety notes for the STO function in the Compax3M ........................... 89
3.10.3.3 Conditions of utilization for the STO function with Compax3M............. 89
3.10.3.4 STO delay times ................................................................................... 90
3.10.3.5 Compax3M STO application description .............................................. 91
3.10.3.6 STO function test .................................................................................. 94
3.10.3.7 Technical details of the Compax3M S1 option ..................................... 96
4. Setting up Compax3..............................................................................97
4.1 Configuration ......................................................................................... 97
4.1.1. Test commissioning of a Compax3 axis ....................................................... 99
4.1.2. Selection of the supply voltage used ............................................................ 99
4.1.3. Motor selection ................................................................................................ 99
4.1.4. Optimize motor reference point and switching frequency of the
motor current ................................................................................................. 100
4.1.5. Ballast resistor............................................................................................... 103
4.1.6. General drive.................................................................................................. 103
4.1.7. Defining the reference system ..................................................................... 104
4.1.7.1 Measure reference.............................................................................. 104
4.1.7.2 Machine Zero...................................................................................... 107
4.1.7.3 Travel Limit Settings ........................................................................... 124
4.1.7.4 Change assignment direction reversal / limit switches....................... 127
4.1.7.5 Change initiator logic .......................................................................... 127
4.1.8. Defining jerk / ramps ..................................................................................... 128
4.1.8.1 Jerk limitation...................................................................................... 128
4.1.8.2 Ramp upon error / deenergize............................................................ 129
4.1.9. Limit and monitoring settings...................................................................... 131
4.1.9.1 Current (Torque) Limit......................................................................... 131
4.1.9.2 Positioning window - Position reached............................................... 131
4.1.9.3 Following error limit............................................................................. 133
4.1.9.4 Maximum operating speed.................................................................. 133
4.1.10. Operating mode / I/O assignment ................................................................ 134
4.1.10.1 I/O assignment for control via the Compax3 inputs/outputs............... 134
4.1.10.2 I/O assignment, control word and status word with control via
COM port............................................................................................. 135

Introduction C3I12T11
6
192-120113 N08 C3I12T11 - December 2010
4.1.11. Encoder simulation ....................................................................................... 139
4.1.11.1 Encoder bypass with Feedback module F12 (for direct drives).......... 139
4.1.12. Absolute- /continuous mode........................................................................ 139
4.1.13. Position mode in reset operation................................................................. 140
4.1.13.1 Examples in the help file..................................................................... 140
4.1.14. Defining the STOP function.......................................................................... 140
4.1.15. Reg-related positioning / defining ignore zone.......................................... 142
4.1.16. Write into set table......................................................................................... 143
4.1.16.1 Dynamic positioning............................................................................ 143
4.1.16.2 Programmable status bits (PSBs)....................................................... 144
4.1.16.3 Set selection ....................................................................................... 145
4.1.16.4 MoveAbs and MoveRel....................................................................... 145
4.1.16.5 Reg-related positioning (RegSearch, RegMove)................................ 146
4.1.16.6 Electronic gearbox (Gearing).............................................................. 150
4.1.16.7 Speed specification (Velocity)............................................................. 151
4.1.16.8 Stop command (Stop)......................................................................... 151
4.1.17. Error response............................................................................................... 151
4.1.18. Configuration name / comments.................................................................. 152
4.2 Configuring the signal Source............................................................ 153
4.2.1. Signal source of the load feedback system................................................ 153
4.2.2. Select signal source for Gearing ................................................................. 153
4.2.2.1 Signal source HEDA........................................................................... 154
4.2.2.2 Encoder A/B 5V, step/direction or SSI feedback as signal source..... 154
4.2.2.3 +/-10V analog speed setpoint value as signal source........................ 156
4.3 Load control......................................................................................... 158
4.3.1. Configuration of load control....................................................................... 160
4.3.2. Error: Position difference between load mounted and motor
feedback too high.......................................................................................... 161
4.3.3. Load control signal image ............................................................................ 161
4.3.3.1 Object for the load control (overview)................................................. 162
4.3.3.2 Objects for load control....................................................................... 162
4.4 Optimization......................................................................................... 163
4.4.1. Optimization window..................................................................................... 164
4.4.2. Scope.............................................................................................................. 165
4.4.2.1 Monitor information............................................................................. 165
4.4.2.2 User interface...................................................................................... 166
4.4.2.3 Example: Setting the Oscilloscope ..................................................... 171
4.4.3. Controller optimization ................................................................................. 173
4.4.3.1 Introduction ......................................................................................... 173
4.4.3.2 Configuration....................................................................................... 176
4.4.3.3 Automatic controller design................................................................. 193
4.4.3.4 Setup and optimization of the control ................................................. 205
4.4.4. Signal filtering with external command value ............................................ 238
4.4.4.1 Signal filtering for external setpoint specification and electronic
gearbox............................................................................................... 238
4.4.4.2 Signal filtering for external setpoint specification and electronic
cam ..................................................................................................... 239
4.4.5. Input simulation............................................................................................. 240
4.4.5.1 Calling up the input simulation............................................................ 240
4.4.5.2 Operating Principle ............................................................................. 241
4.4.6. Setup mode .................................................................................................... 242
4.4.6.1 Motion objects in Compax3................................................................. 243

Parker EME Introduction
192-120113 N08 C3I12T11 - December 2010
7
4.4.7. Load identification......................................................................................... 244
4.4.7.1 Principle .............................................................................................. 244
4.4.7.2 Boundary conditions ........................................................................... 244
4.4.7.3 Process of the automatic determination of the load characteristic
value (load identification) .................................................................... 245
4.4.7.4 Tips ..................................................................................................... 246
4.4.8. Alignment of the analog inputs.................................................................... 247
4.4.8.1 Offset alignment.................................................................................. 247
4.4.8.2 Gain alignment.................................................................................... 247
4.4.8.3 Signal processing of the analog inputs............................................... 248
4.4.9. C3 ServoSignalAnalyzer ............................................................................... 249
4.4.9.1 ServoSignalAnalyzer - function range ................................................ 249
4.4.9.2 Signal analysis overview..................................................................... 250
4.4.9.3 Installation enable of the ServoSignalAnalyzer .................................. 251
4.4.9.4 Analyses in the time range.................................................................. 253
4.4.9.5 Measurement of frequency spectra .................................................... 256
4.4.9.6 Measurement of frequency responses ............................................... 259
4.4.9.7 Overview of the user interface............................................................ 266
4.4.9.8 Basics of frequency response measurement...................................... 279
4.4.9.9 Examples are available as a movie in the help file............................. 284
4.4.10. ProfileViewer for the optimization of the motion profile ........................... 285
4.4.10.1 Mode 1: Time and maximum values are deduced from Compax3
input values......................................................................................... 285
4.4.10.2 Mode 2: Compax3 input values are deduced from times and
maximum values................................................................................. 286
4.4.11. Turning the motor holding brake on and off............................................... 287
5. Control via RS232 / RS485 / USB .......................................................288
5.1 Status diagram..................................................................................... 289
5.2 I/O assignment, control word and status word with control via COM
port........................................................................................................ 290
5.2.1. I/O Assignment .............................................................................................. 290
5.2.2. Control word................................................................................................... 292
5.2.3. Status word 1 & 2........................................................................................... 293
5.3 Examples include: Control via COM port........................................... 294
5.4 Layout of the set table......................................................................... 297
5.4.1. General layout of the table............................................................................ 297
5.4.2. Assignment of the different motion functions............................................ 297
5.4.3. Definition of the states of the programmable status bits (PSBs):............ 298
5.5 Compax3 communication variants..................................................... 298
5.5.1. PC <-> Compax3 (RS232).............................................................................. 299
5.5.2. PC <-> Compax3 (RS485).............................................................................. 301
5.5.3. PC <-> C3M device combination (USB)....................................................... 302
5.5.4. USB-RS485 Moxa Uport 1130 adapter......................................................... 303
5.5.5. ETHERNET-RS485 NetCOM 113 adapter..................................................... 304
5.5.6. Modem MB-Connectline MDH 500 / MDH 504............................................. 305
5.5.7. C3 settings for RS485 two wire operation................................................... 306
5.5.8. C3 settings for RS485 four wire operation.................................................. 307
5.6 COM port protocol ............................................................................... 308

Introduction C3I12T11
8
192-120113 N08 C3I12T11 - December 2010
5.6.1. RS485 settings values................................................................................... 308
5.6.2. ASCII - record................................................................................................. 309
5.6.3. Binary record ................................................................................................. 310
5.7 Remote diagnosis via Modem............................................................. 313
5.7.1. Structure......................................................................................................... 314
5.7.2.Configuration of local modem 1................................................................... 315
5.7.3. Configuration of remote modem 2............................................................... 315
5.7.4. Recommendations for preparing the modem operation........................... 316
6. Compax3 - Objects..............................................................................317
6.1 Object overview I12 T11 ...................................................................... 317
6.2 Detailed object list............................................................................... 320
7. Status values.......................................................................................321
7.1 D/A-Monitor .......................................................................................... 321
7.2 Status values........................................................................................ 321
8. Error.....................................................................................................322
8.1 Error list................................................................................................ 322
9. Order code...........................................................................................323
9.1 Order code device: Compax3 ............................................................. 323
9.2 Order code for mains module: PSUP................................................. 324
9.3 Order code for accessories................................................................. 324
10.Compax3 Accessories........................................................................328
10.1 Parker servo motors............................................................................ 328
10.1.1. Direct drives................................................................................................... 328
10.1.1.1 Transmitter systems for direct drives.................................................. 329
10.1.1.2 Linear motors...................................................................................... 330
10.1.1.3 Torque motors..................................................................................... 330
10.1.2. Rotary servo motors...................................................................................... 330
10.2 EMC measures..................................................................................... 331
10.2.1. Mains filter...................................................................................................... 331
10.2.1.1 Mains filter NFI01/01........................................................................... 332
10.2.1.2 Mains filter NFI01/02........................................................................... 332
10.2.1.3 Mains filter for NFI01/03...................................................................... 333
10.2.1.4 Mains filter NFI02/0x........................................................................... 333
10.2.1.5 Mains filter NFI03/01& NFI03/03 ........................................................ 334
10.2.1.6 Mains filter NFI03/02........................................................................... 335
10.2.2. Motor output filter.......................................................................................... 336
10.2.2.1 Motor output filter MDR01/04.............................................................. 336

Parker EME Introduction
192-120113 N08 C3I12T11 - December 2010
9
10.2.2.2Motor output filter MDR01/01.............................................................. 336
10.2.2.3 Motor output filter MDR01/02.............................................................. 337
10.2.2.4 Wiring of the motor output filter........................................................... 337
10.2.3. Mains filters.................................................................................................... 338
10.2.3.1 Mains filter for PSUP30....................................................................... 338
10.3 Connections to the motor ................................................................... 339
10.3.1. Resolver cable ............................................................................................... 340
10.3.2. SinCos© cable................................................................................................ 341
10.3.3. EnDat cable .................................................................................................... 342
10.3.4. Motor cable..................................................................................................... 342
10.3.4.1 Connection of terminal box MH145 & MH205 .................................... 343
10.3.5. Encoder cable ................................................................................................ 344
10.4 External braking resistors................................................................... 345
10.4.1. Permissible braking pulse powers of the braking resistors..................... 346
10.4.1.1 Calculation of the BRM cooling time................................................... 347
10.4.1.2 Permissible braking pulse power: BRM08/01 with C3S015V4 /
C3S038V4........................................................................................... 348
10.4.1.3 Permissible braking pulse power: BRM08/01 with C3S025V2........... 348
10.4.1.4 Permissible braking pulse power: BRM09/01 with C3S100V2........... 349
10.4.1.5 Permissible braking pulse power: BRM10/01 with C3S150V4........... 349
10.4.1.6 Permissible braking pulse power: BRM10/02 with C3S150V4........... 350
10.4.1.7 Permissible braking pulse power: BRM05/01 with C3S063V2........... 350
10.4.1.8 Permissible braking pulse power: BRM05/01 with C3S075V4........... 351
10.4.1.9 Permissible braking pulse power: BRM05/02 with C3S075V4........... 351
10.4.1.10Permissible braking pulse power: BRM04/01 with C3S150V2........... 352
10.4.1.11Permissible braking pulse power: BRM04/01 with C3S300V4........... 352
10.4.1.12Permissible braking pulse power: BRM04/02 with C3S150V2........... 353
10.4.1.13Permissible braking pulse power: BRM04/02 with C3S300V4........... 353
10.4.1.14Permissible braking pulse power: BRM04/03 with C3S300V4........... 354
10.4.1.15Permissible braking pulse power: BRM11/01 with C3H0xxV4........... 354
10.4.1.16Permissible braking pulse power: BRM12/01 with C3H1xxV4........... 355
10.4.1.17Permissible braking pulse power: BRM13/01 with PSUP10D6.......... 355
10.4.1.18Permissible braking pulse power: BRM14/01 with PSUP10D6.......... 355
10.4.2. Dimensions of the braking resistors ........................................................... 356
10.4.2.1 BRM8/01braking resistors................................................................... 356
10.4.2.2 BRM5/01 braking resistor ................................................................... 356
10.4.2.3 Braking resistor BRM5/02, BRM9/01 & BRM10/01 ............................ 357
10.4.2.4 Ballast resistor BRM4/0x and BRM10/02 ........................................... 357
10.4.2.5 Braking resistor BRM11/01 & BRM12/01 ........................................... 358
10.4.2.6 Ballast resistor BRM13/01 & BRM14/01............................................. 358
10.5 Condenser module C4......................................................................... 359
10.6 Operator control module BDM............................................................ 360
10.7 EAM06: Terminal block for inputs and outputs................................. 361
10.8 Interface cable...................................................................................... 363
10.8.1. RS232 cable.................................................................................................... 363
10.8.2. RS485 cable to Pop ....................................................................................... 364
10.8.3. I/O interface X12 / X22................................................................................... 365
10.8.4. Ref X11............................................................................................................ 365
10.8.5. Encoder coupling of 2 Compax3 axes......................................................... 366
10.8.6. Modem cable SSK31...................................................................................... 367

Introduction C3I12T11
10
192-120113 N08 C3I12T11 - December 2010
10.9 Options M1x ......................................................................................... 368
10.9.1. Input/output option M12................................................................................ 368
10.9.1.1 Assignment of the X22 connector....................................................... 368
10.9.2. HEDA (motion bus) - Option M11................................................................. 369
10.9.3. Option M10 = HEDA (M11) & I/Os (M12) ..................................................... 371
11.Technical Characteristics...................................................................372
12.Index.....................................................................................................390

Parker EME Introduction
192-120113 N08 C3I12T11 - December 2010
11
In this chapter you can read about:
Device assignment ..........................................................................................................11
Scope of delivery.............................................................................................................12
Type specification plate ...................................................................................................13
Packaging, transport, storage..........................................................................................14
Safety instructions ...........................................................................................................16
Warranty conditions.........................................................................................................18
Conditions of utilization....................................................................................................19
1.1 Device assignment
This manual is valid for the following devices:
Compax3S025V2 + supplement
Compax3S063V2 + supplement
Compax3S100V2 + supplement
Compax3S150V2 + supplement
Compax3S015V4 + supplement
Compax3S038V4 + supplement
Compax3S075V4 + supplement
Compax3S150V4 + supplement
Compax3S300V4 + supplement
Compax3H050V4 + supplement
Compax3H090V4 + supplement
Compax3H125V4 + supplement
Compax3H155V4 + supplement
Compax3M050D6 + supplement
Compax3M100D6 + supplement
Compax3M150D6 + supplement
Compax3M300D6 + supplement
PSUP10D6
PSUP20D6
With the supplement:
F10 (Resolver)
F11 (SinCos©)
F12 (linear and rotary direct drives)
I12 T11
1. Introduction

Introduction C3I12T11
12
192-120113 N08 C3I12T11 - December 2010
1.2 Scope of delivery
The following items are furnished with the device:
Manuals*
Installation manual (German, English, French)
Compax3 DVD
Startup Guide (German / English)
*Comprehensiveness of documentation depends on device type
Device accessories
Device accessories for Compax3S
Cable clamps in different sizes for large area shielding of the motor cable, the
screw for the cable clamp as well as
the mating plug connectors for the Compax3S plug connectors X1, X2, X3, and
X4
a toroidal core ferrite for one cable of the motor holding brake
Lacing cord
Device accessories for Compax3M
Cable clamps in different sizes for large area shielding of the motor cable, the
screw for the cable clamp as well as
the matching plug for the Compax3M connectors X14, X15, X43
a toroidal core ferrite for one cable of the motor holding brake
an interface cable (SSK28/23) for communication within the axis combination
Device accessories for PSUP
Matching plug for the PSUP connectors X9, X40, X41
2 bus terminal connectors (BUS07/01) for mains module and the last axis
controller in the combination
Device accessories for Compax3H
Mating connector for X3 and X4
SSK32/20: RS232 adapter cable (programming port C3HxxxV4 - SSK1 - PC)
VBK17/01: SubD jumper mounted

Parker EME Introduction
192-120113 N08 C3I12T11 - December 2010
13
1.3 Type specification plate
The present device type is defined by the type specification plate (on the housing):
Explanation:
1 Type designation
The complete order designation of the device (2, 5, 6, 9, 8).
2
C3:Abbreviation for Compax3
S025:Single axis device, nominal device current in 100mA (025=2.5A)
M050:Multi-axis device, nominal device current in 100mA (050=5A)
H050:High power device, nominal device current in 1A (050=50A)
D6: Designation nominal supply
V2:Mains supply voltage (2=230VAC/240VAC, 4=400VAC/480VAC)
3 Unique number of the particular device
4 Nominal supply voltage
Power Input: Input supply data
Power Output: Output data
5
Designation of the feedback system
F10:Resolver
F11:SinCos© / Single- or Multiturn
F12: Feedback module for direct drives
6
Device interface
I10:Analog, step/direction and encoder input
I11 / I12:Digital Inputs / Outputs and RS232 / RS485
I20:Profibus DP / I21:CANopen / I22:DeviceNet /
I30:Ethernet Powerlink / I31: EtherCAT / I32: Profinet
C20: integrated controller C3 powerPLmC, Linux & Web server
7 Date of factory test
8Options Mxx: I/O extension, HEDA
Sx: optional safety technology on C3M
9
Technology function
T10:Servo drive
T11:Positioning
T30:Motion control programmable according to IEC61131-3
T40:Electronic cam
10 CE compliance
11 Certified safety technology (corresponding to the logo displayed)
12 UL certified (corresponding to the logo displayed)
Compax3 - Type
specification plate
(example):

Introduction C3I12T11
14
192-120113 N08 C3I12T11 - December 2010
1.4 Packaging, transport, storage
Packaging material and transport
Caution!
The packaging material is inflammable, if it is disposed of improperly by burning,
lethal fumes may develop.
The packaging material must be kept and reused in the case of a return shipment.
Improper or faulty packaging may lead to transport damages.
Make sure to transport the drive always in a safe manner and with the aid of
suitable lifting equipment (Weight (see on page 384, see on page 372)). Do never
use the electric connections for lifting. Before the transport, a clean, level surface
should be prepared to place the device on. The electric connections may not be
damaged when placing the device.
First device checkup
Check the device for signs of transport damages.
Please verify, if the indications on the Type identification plate (see on page 13)
correspond to your requirements.
Check if the consignment is complete.
Disposal
This product contains materials that fall under the special disposal regulation from
1996, which corresponds to the EC directory 91/689/EEC for dangerous disposal
material. We recommend to dispose of the respective materials in accordance with
the respectively valid environmental laws. The following table states the materials
suitable for recycling and the materials which have to be disposed of separately.
Material Option
suitable for
recycling
Disposal
Metal yes no
Plastic materials yes no
Circuit boards no yes
Please dispose of the circuit boards according to one of the following methods:
Burning at high temperatures (at least 1200°C) in an incineration plant licensed in
accordance with part A or B of the environmental protection act.
Disposal via a technical waste dump which is allowed to take on electrolytic
aluminum condensers. Do under no circumstances dump the circuit boards at a
place near a normal waste dump.
Storage
If you do not wish to mount and install the device immediately, make sure to store it
in a dry and clean environment (see on page 386). Make sure that the device is
not stored near strong heat sources and that no metal chippings can get into the
device.

Parker EME Introduction
192-120113 N08 C3I12T11 - December 2010
15
Forming the capacitors
Forming the capacitors only required with 400VAC axis controllers and PSUP
mains module
If the device was stored longer than one year, the intermediate capacitors must be
re-formed!
Forming sequence:
Remove all electric connections
Supply the device with 230VAC single phase for 30 minutes
via the L1 and L2 terminals on the device or
multi axis devices via L1 and L2 on the PSUP mains module
Please note in the
event of storage >1
year:

Introduction C3I12T11
16
192-120113 N08 C3I12T11 - December 2010
1.5 Safety instructions
In this chapter you can read about:
General hazards..............................................................................................................16
Safety-conscious working................................................................................................16
Special safety instructions ...............................................................................................17
1.5.1. General hazards
General Hazards on Non-Compliance with the Safety Instructions
The device described in this manual is designed in accordance with the latest
technology and is safe in operation. Nevertheless, the device can entail certain
hazards if used improperly or for purposes other than those explicitly intended.
Electronic, moving and rotating components can
constitute a hazard for body and life of the user, and
cause material damage
Usage in accordance with intended purpose
The device is designed for operation in electric power drive systems (VDE0160).
Motion sequences can be automated with this device. Several motion sequences
can be combined by interconnecting several of these devices. Mutual interlocking
functions must be incorporated for this purpose.
1.5.2. Safety-conscious working
This device may be operated only by qualified personnel.
Qualified personnel in the sense of these operating instructions consists of:
Persons who, by virtue to their training, experience and instruction, and their
knowledge of pertinent norms, specifications, accident prevention regulations and
operational relationships, have been authorized by the officer responsible for the
safety of the system to perform the required task and in the process are capable
of recognizing potential hazards and avoiding them (definition of technical
personnel according to VDE105 or IEC364),
Persons who have a knowledge of first-aid techniques and the local emergency
rescue services.
persons who have read and will observe the safety instructions.
Those who have read and observe the manual or help (or the sections pertinent
to the work to be carried out).
This applies to all work relating to setting up, commissioning, configuring,
programming, modifying the conditions of utilization and operating modes, and to
maintenance work.
This manual and the help information must be available close to the device during
the performance of all tasks.

Parker EME Introduction
192-120113 N08 C3I12T11 - December 2010
17
1.5.3. Special safety instructions
Check the correct association of the device and its documentation.
Never detach electrical connections while voltage is applied to them.
Safety devices must be provided to prevent human contact with moving or
rotating parts.
Make sure that the device is operated only when it is in perfect condition.
Implement and activate the stipulated safety functions and devices.
Operate the device only with the housing closed.
Make sure that all devices are sufficiently fixed.
Check that all live terminals are secured against contact. Perilous voltage levels
of up to 850V occur.
Do not bypass power direct current
Be cautious when performing configuration downloads with master - slave couplings (electronic gear,
cam) Deactivate the drive before starting the configuration download: Master and Slave axis.
Caution!
Due to movable machine parts and high voltages, the device can pose a lethal
danger. Danger of electric shock in the case of non-respect of the following
instructions. The device corresponds to DIN EN 61800-3, i.e. it is subject to
limited sale. The device can emit disturbances in certain local environments. In
this case, the user is liable to take suitable measures.
The device must be permanently grounded due to high earth leakage currents.
The drive motor must be grounded with a suitable protective lead.
The devices are equipped with high voltage DC condensers. Before removing the
protective cover, the discharging time must be awaited. After switching off the
supply voltage, it may take up to 10 minutes to discharge the capacitors.
Danger of electric shock in case of non respect.
Before you can work on the device, the supply voltage must be switched off at the
L1, L2 and L3 clamps. Wait at least 10 minutes so that the power direct current
may sink to a secure value (<50V). Check with the aid of a voltmeter, if the
voltage at the DC+ and DC- clamps has fallen to a value below 50V.
Danger of electric shock in case of non respect.
Do never perform resistance tests with elevated voltages (over 690V) on the
wiring without separating the circuit to be tested from the drive.
Please exchange devices only in currentless state and, in an axis system, only in
a defined original state.
In the event of a axis controller device exchange it is absolutely necessary to
transfer the configuration determining the correct operation of the drive to the
device, before the device is put into operation. Depending on the operation mode,
a machine zero run will be necessary.
The device contains electrostatically sensitive components. Please heed the
electrostatic protection measures while working at/with the device as well as
during installation and maintenance.
Operation of the PSUP30 only with mains filter.
Attention - hot surface!
The heat dissipator can reach very high temperatures (>70°C)
Protective seals
Caution!
The user is responsible for protective covers and/or additional safety measures in
order to prevent damages to persons and electric accidents.

Introduction C3I12T11
18
192-120113 N08 C3I12T11 - December 2010
Forming the capacitors
Forming the capacitors only required with 400VAC axis controllers and PSUP
mains module
If the device was stored longer than one year, the intermediate capacitors must be
re-formed!
Forming sequence:
Remove all electric connections
Supply the device with 230VAC single phase for 30 minutes
via the L1 and L2 terminals on the device or
multi axis devices via L1 and L2 on the PSUP mains module
1.6 Warranty conditions
The device must not be opened.
Do not make any modifications to the device, except for those described in the
manual.
Make connections to the inputs, outputs and interfaces only in the manner
described in the manual.
Fix the devices according to the mounting instructions (see on page 68, see on
page 74).
We cannot provide any guarantee for other mounting methods.
Note on exchange of options
Device options must be exchanged in the factory to ensure hardware and software
compatibility.
When installing the device, make sure the heat dissipators of the device receive
sufficient air and respect the recommended mounting distances of the devices
with integrated ventilator fans in order to ensure free circulation of the cooling air.
Make sure that the mounting plate is not exposed to external temperature
influences.
Please note in the
event of storage >1
year: