Paser CF0026UNPS51 User manual

Release date: 15.07.19 rev 1.0 19
1 / 5
DESCRIPTION
SMARTPARK is an electronic module, easy to install, that allows you to integrate professionally aermarket parking sensors on the Volkswagen Group
vehicles equipped with the O M radio.
The device allows to display on the O M radio of Volkswagen group the signalling of the parking sensors as it happens for the O M parking sensors.
VOLKSWAGEN
SMART PARK CF0026UNPS51
CANBUS MODULE TO DISPLAY FRONT / REAR PARKING SENSORS ON OEM RADIO SCREEN.
Vod fone R294 - R394 - AMR394/F
INSTALLATION MANUAL
45’
CONNECTIONS
Wires exit view
CAN H
CAN L
12 VDC
GND
CAN H
CAN L
12 VDC
GND
F kr 40 PINS F kr 52 PINS
SMARTPARK
REMOTE SWITCH
CONNECTOR
REAR SPEAKER
FRONT SPEAKER
ON / OFF MANUAL OF THE PARKING SENSORS
If the vehicle is equipped with steering wheel controls, by pressing OK bu'on for 3 seconds on the steering
wheel controls, sensors will turn on / off. This opera*on is manageable if the vehicle is driving below 10 km / h
CAUTION
FOR THE CORRECT OPERATION OF THE SYSTEM, THE VEHICLE MUST BE ENABLED AT THE DISPLAY, THROUGH THE OFFICIAL DIAGNOSTIC DEVICE
OF VOLKSWAGEN.
ATTENTION: PLEASE PLACE THE PARKING SENSOR CONTROL UNITS ON THE RIGHT SIDE OF THE VEHICLE
SYSTEM WORKS WITH IGNITION ON.
THE SYSTEM ACTIVATES BY INSERTING THE REVERSE AND DEACTIVATES AFTER 10 SECONDS BY REMOVING THE REVERSE
OR EXCEEDING 10 KM / H.
J1
J2
J3
A GND
J1
J2
J3
A GND

Release date: 15.07.19 rev 1.0 19
2 / 5
ALTERNATIVE CONNECTION DRIVER SIDE LOCATION
J1
J2
J3
A GND
J1 J2
J3
A GND
SMARTPARK
REMOTE SWITCH
CONNECTOR
REAR SPEAKER
FRONT SPEAKER
1
7 14
CAN L
CAN H
ATTENTION: PLEASE PLACE THE PARKING SENSOR CONTROL UNITS ON THE RIGHT SIDE OF THE VEHICLE
SYSTEM WORKS WITH IGNITION ON.
THE SYSTEM ACTIVATES BY INSERTING THE REVERSE AND DEACTIVATES AFTER 10 SECONDS BY REMOVING THE REVERSE
OR EXCEEDING 10 KM / H.
SMART PARK CF0026UNPS51
CANBUS MODULE TO DISPLAY FRONT / REAR PARKING SENSORS ON OEM RADIO SCREEN.
Vod fone R294 - R394 - AMR394/F
INSTALLATION MANUAL
45’

Release date: 15.07.19 rev 1.0 19
3 / 5
AUDI A1 CONNECTIONS
J1
J2
J3
A GND
J1 J2
J3
A GND
SMARTPARK
REMOTE SWITCH
CONNECTOR
REAR SPEAKER
FRONT SPEAKER
CAN H CAN L
SMART PARK CF0026UNPS51
CANBUS MODULE TO DISPLAY FRONT / REAR PARKING SENSORS ON OEM RADIO SCREEN.
Vod fone R294 - R394 - AMR394/F
INSTALLATION MANUAL
45’
ATTENTION: PLEASE PLACE THE PARKING SENSOR CONTROL UNITS ON THE RIGHT SIDE OF THE VEHICLE
SYSTEM WORKS WITH IGNITION ON.
THE SYSTEM ACTIVATES BY INSERTING THE REVERSE AND DEACTIVATES AFTER 10 SECONDS BY REMOVING THE REVERSE
OR EXCEEDING 10 KM / H.

Release date: 15.07.19 rev 1.0 19
4 / 5
DESCRIPTION
SMARTPARK is an electronic module, easy to install, that allows you to integrate professionally aermarket parking sensors on the Peugeot Group vehicles
equipped with the O M radio.
The device allows to display on the O M radio of Peugeot group the signalling of the parking sensors as it happens for the O M parking sensors.
PEUGEOT
SMART PARK CF0026UNPS51
CANBUS MODULE TO DISPLAY FRONT / REAR PARKING SENSORS ON OEM RADIO SCREEN.
Vod fone R294 - R394 - AMR394/F
INSTALLATION MANUAL
45’
CONNECTIONS
CAN H
CAN L
GND
12 VDC
F kr 40 vie
J1 J2
J3
A GND
J1
J2
J3
A GND
SMARTPARK
REMOTE SWITCH
CONNECTOR
SMARTPARK DOES NOT NEED
SPEAKERS BECAUSE
ACOUSTIC SIGNALS ARE
GENERATED BY OEM RADIO
SMARTPARK DOES NOT NEED
SPEAKERS BECAUSE
ACOUSTIC SIGNALS ARE
GENERATED BY OEM RADIO
ATTENTION: PLEASE PLACE THE PARKING SENSOR CONTROL UNITS ON THE RIGHT SIDE OF THE VEHICLE
SYSTEM WORKS WITH IGNITION ON.
THE SYSTEM ACTIVATES BY INSERTING THE REVERSE AND DEACTIVATES AFTER 10 SECONDS BY REMOVING THE REVERSE
OR EXCEEDING 10 KM / H.
CAUTION
FOR THE CORRECT OPERATION OF THE SYSTEM, THE VEHICLE MUST BE ENABLED AT THE DISPLAY, THROUGH THE OFFICIAL DIAGNOSTIC DEVICE
OF PEUGEOT.

Release date: 15.07.19 rev 1.0 19
5 / 5
SMART PARK CF0026UNPS51
CANBUS MODULE TO DISPLAY FRONT / REAR PARKING SENSORS ON OEM RADIO SCREEN.
Vod fone R294 - R394 - AMR394/F
INSTALLATION MANUAL
45’
WARRANCY
THIS PRODUCT IS GUARANTEED FOR 2 YEARS FOR ANY MANUFACTURING DEFECTS. FISCAL DOCUMENT SERVES AS GUARANTEE VALIDITY.
Technic l support:: +39 0141 - 947676
The informa*on in this guide are purely for informa*on purposes, therefore, are subject to change without no*ce. At the *me of publica*on the informa*on is
correct and reliable. However Paser can not be held responsible for any consequences resul*ng from errors or omissions in this manual. Paser reserves the
right to improve / change the product or manual without obliga*on to no*fy users.
SYSTEM WORKS WITH THE IGNITION ON.
SYSTEM STARTS TO WORK BY INSERTING THE REVERSE AND IT SWITCHES OFF AFTER 10 SECONDS BY REMOVING THE REVERSE OR EXCEEDING 10 KM / H.
IF YOU NEED TO INSTALL THE SAME UNIT IN A NEW CAR, IT IS NECESSARY TO RESET THE MODULE.
RESET:
1. WITH THE UNIT POWERED, PRESS AND KEEP PRESSED THE UNIT BUTTON TILL THE LED SWITCHES OFF.
2. WITH THE LED SWITCHED OFF, RELEASE THE BUTTON: THE RESET IS DONE.
ATTENTION
TECHNICAL CHARACTERISTIS
POW R 10/16 VDC
SL P MOD ABSORPTION <1 mA
WORKING MOD ABSORPTION 100 mA
TROUBLESHOOTING
P rking Sensor UNIT
PROBLEM CAUSE SOLUTION
The system doesn’t work when the b ck ge r is
inserted.
Wrong connec@on of the power wires Power the p rking sensors by the reverse ge r light
Wrong connec@on of the plugs Verify the connec@on of the connectors of the
p rking system
The system detects lw ys the obst cle
The system detects the ground Verify th t the sensors c ps re inst lled horizon-
t lly respect the ground.
C ps sensors re v rnished
incorrectly
Verify th t the c ps v rnish l yer is not too thick.
In this c se the sensors c n detect it s n obst -
cle.
The test is m de in closed sp ce Ple se m ke the test of the system in n open
sp ce nd not into close room.
The sound of the buzzer is not v il ble
BUZZER not connected
(only for VW c rs)
Check the connec@on between Buzzer
nd p rking sensors Unit
Wrong connec@ons of the c ps sensors Ple se control the c ps sensors connec@on
SMARTPARK
PROBLEM CAUSE SOLUTION
The unit doesn’t m n ge ny func@on nd the
LED is OFF. Wrong connec@on of the power wires Verify the power connec@ons
The unit is right connected but it doesn’t m n ge
ny func@on nd the LED is OFF. Wrong connec@on of the CANBUS wires Verify the CANBUS connec@ons
The unit is right connected nd the LED blinks
RED quickly.
CANBUS protocol unknown or upgr ded by the c r
m nuf cturer
The unit is not ble to synchronize the CANBUS
protocol; ple se cont ct the distributor
The unit is right connected nd the LED blinks
RED irregul rly. Wrong connec@on of the CANBUS wires Verify the CANBUS connec@ons
The unit is right connected nd the LED switches
on RED.
CANBUS protocol unknown or upgr ded by the c r
m nuf cturer
The unit is not ble to synchronize the CANBUS
protocol; ple se cont ct the distributor