Patton electronics 510 User manual

USER
MANUAL
MODEL 510, 511
and 512
Modular Surge
Protectors
SALES OFFICE
[phone]
TECHNICAL SUPPORT
[phone]
http://www.patton.com
Part# 07M510/11/12-B2
Doc# 074251UB2
Revised 01/16/96

1.0 WARRANTY INFORMATION
Patton Electronics warrants all Model 510/511/512 components to
be free from defects, and will—at our option—repair or replace the
product should it fail within one year from the first date of shipment.
This warranty is limited to defects in workmanship or materials, and
does not cover customer damage, abuse or unauthorized modification.
If this product fails or does not perform as warranted, your sole
recourse shall be repair or replacement as described above. Under no
condition shall Patton Electronics be liable for any damages incurred
by the use of this product. These damages include, but are not limited
to, the following: lost profits, lost savings and incidental or
consequential damages arising from the use of or inability to use this
product. Patton Electronics specifically disclaims all other warranties,
expressed or implied, and the installation or use of this product shall be
deemed an acceptance of these terms by the user.
1.2 SERVICE
All warranty and non-warranty repairs must be returned freight
prepaid and insured to Patton Electronics. All returns must have a
Return Materials Authorization number on the outside of the shipping
container. This number may be obtained from Patton Electronics
Technical Service at [phone].
Packages received without an
RMA number will not be accepted.
Patton Electronics' technical staff is also available to answer any
questions that might arise concerning the installation or use of your
Model 510/511/512. Technical Service hours: 8AM to 5PM EST,
Monday through Friday.
1
2.0 GENERAL INFORMATION
Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is
warranted for One Year parts and labor. If any questions or problems
arise during installation or use of this product, please do not hesitate to
contact Patton Electronics Technical Support at [phone].
2.1 FEATURES
• Superior surge protection clamps voltages in 0.5 µS
• Power handling capability up to 600 watts peak per wire
• Clamping voltages of 6 volts (RS-422) or 25 volts (RS-232)
• Available with RJ-11, RJ-12 and RJ-45 connectors
• Heavy braided ground strap shunts surges directly to chassis
ground
• Fits into tight installation spaces
• Made in USA
2.2 DESCRIPTION
The Patton Model 510/511/512 data line surge protector uses the
latest in transient surge suppression technology to guard against loss of
data or damage to equipment. Featuring a power handling capacity up
to 600 watts per wire, the Model 510/511/512 diverts harmful surges to
ground before they reach your sensitive equipment.
The Model 510/511/512 is equipped with a heavy duty braided
metal strap to shunt harmful over-voltages safely to chassis ground.
Housed in a sturdy, flame retardant plastic case, the Model 510/511/512
connects in-line to data communication equipment using modular
interfaces.
The Model 510 protects all 4 lines on an RJ-11 interface. The
Model 511 protects all 6 lines on an RJ-12 interface. The Model 512
protects all 8 lines on an RJ-45 interface. All three models are
available in either RS-232 (25 volt clamping threshold) or RS-422
(6 volt clamping threshold) versions.
Warning—Should your equipment or building be subject to a direct
lightening strike, this product will not provide complete protection.
2

3.0 INSTALLATION
The Patton Model 510/511/512 is easy to install. The following
instructions will clearly explain each step:
1. Connect the unit between the data line and the equipment that
is to be protected. We use a bi-directional circuit, so you don't
need to worry about an input side and an output side.
2. Connect the braided ground strap directly to a chassis ground
connection on the protected device. If you are unsure where
to locate a frame ground connection on your equipment, be
sure to consult the equipment’s user manual or contact the
manufacturer—the ground connection is critical for proper
operation of the Model 510/511/512.
APPENDIX A
PATTON MODEL 510/11/12 SPECIFICATIONS
Models 510/6 and 510/25
Connectors: RJ-11 (4-wire)
Pins Wired/Protected: All 4 pins on RJ-11 interface
Surge Capacity: 600 W for 1 mS
Response Time (RS-422): Clamped to + or - 6 volts after 0.5 µS,
200 Amps with a 8/20 µS pulse
Response Time (RS-232): Clamped to + or - 25 volts after 0.5 µS,
200 Amps with a 8/20 µS pulse
Models 511/6 and 511/25
Connectors: RJ-12 (6-wire)
Pins Wired/Protected: All 6 pins on RJ-12 interface
Surge Capacity: 600 W for 1 mS
Response Time (RS-422): Clamped to + or - 6 volts after 0.5 µS,
200 Amps with a 8/20 µS pulse
Response Time (RS-232): Clamped to + or - 25 volts after 0.5 µS,
200 Amps with a 8/20 µS pulse
Models 512/6 and 512/25
Connectors: RJ-45 (8-wire)
Pins Wired/Protected: All 8 pins on RJ-45 interface
Surge Capacity: 600 W for 1 mS
Response Time (RS-422): Clamped to + or - 6 volts after 0.5 µS,
200 Amps with a 8/20 µS pulse
Response Time (RS-232): Clamped to + or - 25 volts after 0.5 µS,
200 Amps with a 8/20 µS pulse
Copyright © 1999
Patton Electronics Company
All Rights Reserved
Model 510/11/12
Surge Protector
Connection to
frame ground
Output to protected
equipment
UTP input
from network
Figure 1. How to Connect the Model 510/11/12 Braided Ground
Strap to the Chassis Ground Connection
34