PEERLESS Smartmount ST630P and assembly Guide

Max UL Load Capacity: 80 lb (36.3 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 04-27-05 SHEET #: 201-9421-8 04-09-07
Features:
• Fits 10" to 24" LCD flat panel screens
• One-touch tilt for effortless positioning and adjustment of the screen
Installation and Assembly:
SmartMount™ Universal Tilt Wall Mount
for 10" - 24" LCD Flat Panel Screens
Models: ST 630P, ST 630P-S, ST 630, ST 630-S
R
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.

2 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-8 04-09-07
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
•studfinder("edgetoedge"studfinderisrecommended)
•phillipsscrewdriver
•drill
•1/4" bit for concrete and cinder block wall
•1/2" bit for metal stud wall
•5/32" bit for metal or wood stud wall
•level
Accessories
• Metal Stud Fastener Kit (ACC 215) (Not evaluated by UL)
• VideoConferencingShelf(ACC 309) (Not evaluated by UL)
• Accessory Shelves (PM 600, PM 610) (Not evaluated by UL)
• Donotbegin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
callPeerless customer careat1-800-865-2112.
• Thisproduct should only be installed byaqualified professional.
• Makesurethat the wall will safely support the combined load of the equipment and all attached hardware and compo-
nents.
• Neverexceedthe Maximum UL Load Capacity of 80 lb (36.3 kg).
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edgeto edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrews firmly, but donot overtighten. Overtightening can damagethe items, greatly reducing theirholding
power.
WARNING
Table of Contents
Parts List..............................................................................................................................................................................3
Installation to Single Wood Stud Wall...................................................................................................................................4
Installation to Solid Concrete or Cinder Block .......................................................................................................................5
Attaching Adapter Plate to Flat Panel Screen ......................................................................................................................6
InstallingandRemovingFlatPanelScreen ...........................................................................................................................7
Adjusting the Tilt Angle of the Flat Panel Screen..................................................................................................................7
Forcustomer care call [phone] or [phone].

3 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-8 04-09-07
GC D E F
AB
H
ST 630P ST 630P-S ST 630 ST 630-S
Description Qty Part # Part # Part # Part #
Aadapter plate 1 095-1346 095-4346 095-1346 095-4346
Btilt assembly 1 095-0359 095-0360 095-0359 095-0360
CAlligator® anchor 2 590-0097 590-0097 590-0097 590-0097
DM4 x 10 mm phillips screw 4 504-9012 504-9012 504-9012 504-9012
EM4 x 20 mm phillips screw 4 504-9020 504-9020 504-9020 504-9020
Fretaining spacer 4 590-5005 590-5005 590-5005 590-5005
G#14 x 2-1/2" hex head wood screw 2 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03
HM5 x 6 mm screw 1 520-1023 520-1023 520-1114 520-1114
Isecurity driver 1 560-1133 560-1133
Parts List
I

4 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-8 04-09-07
Installation to Single Wood Stud Wall
1Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based
on its edges, draw a vertical line down the stud’s center. Place tilt assembly (B) on wall as a template, making sure
that the two mounting holes are over the stud centerline. Level tilt assembly, and mark the center of the two holes.
Drill two 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the tilt assembly is level, secure it using two
#14 x 2-1/2" wood screws (G) as shown.
Skip to step 2 on page 6.
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and
components.
WARNING
• Tighten wood screws so that tilt assembly is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
• Hardwareprovided is for attachment ofmount through standard thickness drywallorplaster into wood studs. Installers
areresponsible to providehardware for other typesof mounting situations.
WARNING
G
B

5 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-8 04-09-07
Installation to Solid Concrete or Cinder Block
1Make sure that tilt assembly (B) is level, use it as a
template to mark two mounting holes. Drill two 1/4"
(6 mm) dia. holes to a minimum depth of 2-1/2"
(64 mm). Insert anchors (C) in holes flush with wall
as shown (right). Place tilt assembly over anchors
and secure with two #14 x 2-1/2" screws (G). Level,
then tighten all fasteners.
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and
components.
WARNING
CUTAWAY VIEW
INCORRECT
concrete
surface
1
3
2
Drill holes and insert anchors (C).
CORRECT
Place assembly (B)over anchors (C) and secure with screws (G).
Tighten all fasteners.
wall
plate
plaster/
drywall
concrete wall plate concrete
plaster/
drywall
• Always attach concrete expansion anchors directly to
load-bearingconcrete.
• Neverattach concrete expansion anchorsto concrete
coveredwith plaster,drywall, or other finishingmate-
rial.If mounting to concrete surfacescoveredwith a
finishingsurface isunavoidable,the finishingsurface
must be counterbored asshown below. Be sure
concreteanchors do not pull away from concrete
whentightening screws. If plaster/drywall is thicker
than 5/8", custom fasteners must be supplied by
installer.
WARNING
B
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
C
G
C
G
CINDERBLOCK
SOLID
CONCRETE
B
C

6 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-8 04-09-07
F
*For screens with a hole
pattern in a pocket,
spacers (F) go between
adapter plate (A) and
screen.
FORVESA®75MOUNTINGPATTERN:
Chooseholepattern asshown below.Attachadapter
plate (A) to back of screen using four M4 x 10 mm
screws(D) asshown below.
*Note: If hole pattern is in a pocket, attach adapter
plate (A) to back of screen using four M4 x 20 mm
screws(E)andfourretainingspacers(F)asindicated
below.
Attaching Adapter Plate to Flat Panel Screen
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
D
FORVESA100MOUNTINGPATTERN:
Chooseholepattern asshown below.Attachadapter
plate (A) to back of screen using four M4 x 10 mm
screws(D) asshown below.
D
2
A
A

7 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-8 04-09-07
Attach screen to tilt assembly (B). Tighten M5 x 6
mm screw (H) to lock screen to tilt assembly.
Note: For security models, use security driver (I) to
tighten M5 x 6 mm screws (H).
Toremove screen frommount,loosen screw (H)and
lift screen off of mount.
Installing and Removing Flat Panel Screen
3
• Do not lift more weight than you can handle. Use
additionalman power ormechanical lifting equipment
to safely handle placement of the screen.
• Failure to lock adapter plate (A) with screw (H) can
cause screen to come off mount if hit accidentally.
• Do not tighten screws with excessive force.
Overtighteningcan causedamageto mount. Tighten
screws to 20 in. • lb (2.26 N.M.) maximum torque.
CAUTION
WARNING
Adjust tension knob on right side of mount shown in
figure 4 to desired tension to balance your screen
size and weight.
Note: Ifknobis inaccessible, remove screen from
mount, adjust tension knob to desired tension to
balance your screen size and weight, and reattach
screen to mount as stated in step 3.
Push or pull from top or bottom of screen to adjust
tilt as shown in figure 4. The tilt can be adjusted to a
maximumof 15° forward or 5° backward.
4
Adjusting the Tilt Angle of the Flat Panel Screen
• Becareful not to pinch fingers whenpushingscreen
fromthe bottom.
CAUTION
• Do not tighten screws with excessive force.
Overtighteningcan causedamageto mount. Tighten
screws to 40 in. • lb (4.5 N.M.) maximum torque.
CAUTION
fig. 4
TENSIONKNOB
A
SCREEN H
B
fig. 3
©2007,PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.