PEERLESS SP730P and assembly Guide

Max ULLoad Capacity: 25 lb (11.3 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06
Installation and Assembly:
LCD Screen Long Pivot Wall Mount
Models: SP730P, SP730P-S, D-LPL-100, RTLPL-100S
Features:
•Fits 10" - 22" LCD screens
• Arm extends up to 6" from wall or folds flat to save space
• Supports screens with VESA®75 or 100 mounting holes
• Featuresball jointat thescreen foradditional side-to-sideswivel
andupwardand downward tilt
R

2 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06
Forcustomer care call(800) 729-0307 or [phone].
Table of Contents
Parts List.............................................................................................................................................................................. 3
Installation to Wood Stud Wall ............................................................................................................................................. 4
Installation to Solid Concrete and Cinder Block .................................................................................................................... 5
Tools Needed for Assembly
• studfinder ("edgeto edge"stud finderis recommended)
• phillipsscrewdriver
• drill with 1/4" and 5/32" drill bits
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call
Peerless customer service at 1-800-729-0307.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never mount this product to a metal stud wall construction unless the stud can be verified to be constructed of 25
gauge steel minimum, the drywall is 1/2" thick minimum and you obtain and use the Peerless accessory kit for metal
studs.
• Neverexceed the MaximumULLoadCapacity.
• If mounting to wood wall stud wall construction, make sure that mounting screws are anchored into the center of the
studs. Use of an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power. See suggested torque values where applicable within these instructions.
WARNING
Accessories
• Metal StudAccessory Kit (ACC 908) (Not evaluated by UL)
Notes:
• Read entire instruction sheet before you start installation and assembly.
• Screen must be attached to the mount to enable tilting.

3 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06
B
A
E
F
D
C
H
G
D-LPL-100
SP730P SP730P-S
Description Qty. Part # Part #
Awall arm 1 095-0383-B 095-0383-S
Bcord management clip 2 590-1264 590-2164
C3/16" allen wrench 1 560-0071 560-0071
D#14 x 2-1/2" flat head wood screw 2 520-1202 520-2165
EAlligator® anchor 2 590-0097 590-0097
FM4 x .7 x 12 mm phillips screw 4 504-9013 504-2013
GM4 x .7 x 20 mm phillips screw 4 504-9020 504-2014
Hretaining spacer 4 590-5005 590-5003
I5 mm allen wrench 1 560-9640 560-9640
Parts List
B
I
RTLPL-100S

4 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06
Installation to Wood Stud Wall
Using a stud finder, locate and mark the edges of the wood stud used in mounting this product. Use of an edge to
edge stud finder is highly recommended. Use a level to draw a vertical line down the center of the stud. Use wall
plate as template to mark center of holes along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (65 mm)
deep.Attach wall arm assembly (A) to wall using two #14 x 2.5" flat head wood screws (D) as shown.
Skip to step 2 on page 6.
1
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardwareandcomponents.
WARNING
• Tightenscrews sothat wallplate isfirmly attached,but do not overtighten. Overtightening can damage the screws,
greatlyreducingtheirholdingpower.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is
highlyrecommended.
WARNING
A
D
WOOD
STUD
WALL

5 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06
Installation to Solid Concrete and Cinder Block
1
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.
It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid
breakingout the back of thehole when enteringa void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardwareandcomponents.
WARNING
Level and use wall plate as template to mark center
of holes. Drill two 1/4" (6 mm) dia. holes to a
minimum depth of 2" (51 mm). Insert anchors (E) in
holes flush with wall as shown in fig 1.3. Place wall
arm(A) over anchorand secure with wood screw(D)
as shown in figures 1.4 and 1.6. Make sure wall arm
is level, and tighten all fasteners. See figure 1.5.
• Concrete anchors are notintended forattachment to
concretewall covered witha layer ofplaster,drywall,
orother finishing material asshown below.Ifmounting
toconcrete wall coveredwith plaster/drywall is
unavoidable,plaster/drywall (up to5/8" thick) must be
counterboredas shown below.Besure concrete
anchorsdo not pullaway from concretewhen tighten-
ing screws. If plaster/drywall is thicker than
5/8", custom fasteners must be supplied by installer.
WARNING
E
concrete
wall
E
Drill holes
and insert
anchors.
Place wall
plate over
anchor and
secure with
screw.
Tighten all
fasteners.
D
WALLPLATE
fig 1.3
fig 1.4
fig 1.5
CUTAWAYVIEW
CORRECT
concrete
plaster/
drywall
INCORRECT
concrete
plaster/
drywall
A
• Tighten screws so that wall plate is firmly attached,
butdonotovertighten. Overtightening can damage the
screws,greatlyreducing their holdingpower.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
A
DE
A
fig 1.6

6 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06
Insert two M4 x 12 mm screws (F) into top two holes
ofscreen, leaving approximately 1/4" ofexposed
thread. Hook screws onto keyslots of adapter plate
as indicated in figures 2.1 and 2.2.
*Note: If hole pattern is in a pocket, insert two M4 x
20 mm screws (G) with two retaining spacers (H)
into top two holes of screen as indicated right.
2
3
fig. 2.1
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
Note: Toadd security, orderACC 918 for security
screws.Refer toACC 918 instruction sheet for
installing security screws.
1/4"
H
*For screens with a
hole pattern in a
pocket, spacers (H)
go between adapter
plate and screen.
FOR VESA®75
MOUNTINGPATTERN: FOR VESA100 MOUNTINGPATTERN:
fig. 2.2
F
Screen may appear
slightlydifferentthan
illustrated
Insert one M4 screw (F or G) through bottom hole of
adapterplateas shown infigure3.1.
fig. 3.1
F or G
ADAPTER
PLATE

7 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06
Bdetail 1
Route cords through center of cord management clip (B). Next, attach cord management clip (B) to adapter plate
using M4 screw (F or G) as shown in detail 1. Tighten all four screws (F or G).
Note:An additional cord management clip (B) was added for additional cords. If you want to use this additional clip,
remove the opposite bottom screw and repeat this step on opposite side of adapter plate.
4
F or G

8 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06
If more or less tension is desired in the arm pivot points, do the following:
• To increase tension, turn socket screw clockwise with 3/16" allen wrench (C).
• To reduce tension, turn socket screw counter-clockwise with allen wrench (C). Do not turn more than half a turn.
©2006PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
NOTE: Adjustmentpoints(socket screws) are factory torquedfor optimal performance. This factory torque setting is
recommended to prevent the screen from slipping over time. Ifmore or lesstension isdesired follow thisoptional
step. You may not achieve optimal torque value if factory torque settings are adjusted.
If more or less tension is desired in tilt mechanism, remove snap caps as shown in detail 2. Insert a flat head screw
driver into slot and pry cap away from tilt mechanism. To adjust tilt, simply tighten or loosen socket screw no more
than half a turn using 5 mm allen wrench (I).To adjust roll, simply tighten or loosen 10-32 nylock nut.
SNAPCAP
SOCKET
SCREW
10-32NYLOCKNUT
detail 2
OPTIONAL
SLOT
• Donotremovescreworloosenscrewuntil it is nolongerengagedwiththemount.Doingsomaycausethescreentofall.
WARNING
SOCKETSCREW

Capacité de charge maximale :
11,3 kg (25 lb)
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 06-10-05 SHEET #: 095-9225-7 08-28-06
Installation et assemblage :
Monture réglable pour fixation d’écran à cristaux
liquides sur un mur/une armoire
Modèles :SP730P, SP730P-S, D-LPL-100, RTLPL-100S
Caractéristiques :
•Convient aux écrans à cristaux liquides de 25 à 55 cm (10 à 22 po)
•Le bras d’étend à une distance maximale de 15 cm (6 po) du mur et
se replie à plat pour économiser de la place
•Convient aux écrans dotés de trous de montage VESA®75 ou 100
•L’écran comporte un joint à rotule qui accroît le pivotement latéral et
l’inclinaison vers le haut et vers le bas.
R

10 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06
Pourle serviceà laclientèle, appelezle 011+1+[phone].
Outils nécessaires pour l’assemblage
• localisateur de montants (le localisateur de montants « bord à bord » est recommandé)
• tourneviscruciforme
• perceuse à mèches de 6,35 mm (1/4 po) et 3,96 mm (5/32 po)
Accessoires
• Kit d’accessoires pour montants métalliques (ACC 908)
Table des matières
Liste des pièces ..................................................................................................................................................................11
Installation sur un mur à montants en bois ......................................................................................................................... 12
Installation sur du béton plein ou un bloc de béton de mâchefer ......................................................................................... 13
•Ne commencez pas à installer votre produit Peerless avant d’avoir lu et assimilé les instructions et les mises en
garde contenues dans cette fiche d’instructions. Pour toute question concernant les instructions ou les mises en
garde,appelez leservice à la clientèle de Peerless au011+1+[phone].
•Ceproduit ne doit être installé que par une personne ayant de bonnes aptitudes en mécanique, expérimentée en
travauxde construction de base, et démontrant une parfaite compréhension de ces instructions.
•Assurez-vousque lasurface desupport pourra soutenir sans difficulté la charge combinée de l’équipement, de toute
sa visserie et de tous ses composants.
•Ne montez jamais ce produit sur un mur à montants métalliques sans vous assurer que le montant est en acier de
calibre 25 au minimum, que la cloison sèche a au moins 12,5 mm (1/2 po) d’épaisseur et sans utiliser le kit
d’accessoires Peerless pour montants métalliques.
•Ne dépassez jamais la capacité de charge maximum.
•Si vous effectuez le montage sur un mur à montants en bois, assurez-vous que les vis de montage sont ancrées au
centre des montants. L’usage d’un localisateur « bord à bord » est fortement conseillé.
•Pourlever etpositionner l’équipement en toute sécurité, faites-vous toujours aider par une autrepersonne ouutilisez
unmatériel de levage mécanique.
• Serrez fermement les vis, mais sans excès. Un serrage excessif peut endommager les éléments et en réduire
considérablementle pouvoir de maintien. Référez-vous aux couplesde serrage suggérés dans ces instructions, dans
les cas applicables.
AVERTISSEMENT !
Remarques :
• Lisez entièrement la fiche d’instructions avant de commencer l’installation et l’assemblage.
• L'écrandoit être fixé au bâti pour permettre l'inclinaison.