Pelican StealthLite 2460 User manual

PELICANTM
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
OPERATING INSTRUCTIONS
CHARGING INSTRUCTIONS
To ensure long term performance charge
battery for 24 hours or more before first use.
“Quick Charge” CHARGE TIME 3 TO 4 HRS.
1. Push the AC/DC Power Transformer plug into the
Charger Socket (the transformer socket is located in
a pocket in the base). Plug transformer into electri-
cal receptacle. The LED should be SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will pulse RED.
3. When the LED changes to SOLID GREEN the light
is fully charged and ready to use.
“Slow Charge” CHARGE TIME
16 TO 18 HOURS (CAR, RV OR BOAT)
1. Push the cigarette lighter adapter (CAT #8056)
into the vehicle’s socket and plug the transformer
into the charging base. The LED should be
SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will glow RED.
ON/OFF
Swing the switch lever to the right (light facing
away from you) until light activates. To turn light off,
swing the switch lever to the left (light facing away
from you) until the light goes off.
BATTERY PACK INSTALLATION
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp and contact module.
3. Remove used battery pack and replace with a
fresh battery pack. The battery pack has a plastic
rib to ensure that it can only be installed one way.
4. Replace the contact module and lamp.
5. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing slightly.
ALKALINE BATTERY (OPTION)
Insert 4 AA cell batteries (2 in-line with + end
up and 2 in-line + end down) as indicated on
polarity sticker located on the inside of the light.
SCUBA DIVING APPLICATION
Check closely for cuts, scratches, or an otherwise
damaged o-ring or mating lens lip surface as this
can cause the light to flood under pressure. Remove
any salt deposits, sand, dirt, or other foreign mat-
ter from the o-ring sealing surfaces. KEEP THE
THREADS, O-RING GROOVE AND INSIDE LIP OF
LENS LUBRICATED WITH SILICONE GREASE.
WARNING: Do not charge alkaline batteries.
LAMP REPLACEMENT
To replace the lamp module follow steps in
the battery installation section as listed below:
To remove lamp module follow steps #1 and #2.
To replace lamp module follow steps #4 and #5.
CAUTION:
If light is not to be used for some time, remove bat-
teries to prevent possible leakage and corrosion.
CHARGER BASE
MOUNTING INSTRUCTIONS
The charger base can be permanently mounted using
double sided tape (included) or with two
#8 screws (not included).
VEHICLE INSTALLATION
The charger base can be permanently mounted
in most vehicles and this operation should be
performed by a professional auto technician.
When installing the charger, ensure that the
DIRECT WIRING RIG is connected to an ignition key-
switch line.The high amperage draw of the charger
may drain the vehicle’s battery if
connected directly to the battery.
PRODUCT SPECIFICATIONS
Lamp Type: LED
Battery Burn Time: 32 hours
Battery Type:4.8V NiMH (4-cell)
Battery Brand: Use Pelican Cat. #2469
HYDROGEN GAS ABSORBER
Internal catalyst pellets, located on the lamp, are there
to help absorb hydrogen gas that could
possibly be emitted by defective, leaking, reversed
polarity or heavily discharged batteries. If the
pellets become lost or damaged, replace lamp imme-
diately. If pellets become wet, let them air dry. Pelican
Products assumes no liability for any brand of batteries
which are defective or cause injury to anyone when
used in any Pelican flashlight.
StealthLiteTM 24 60
RecoilTM LED
RECHARGEABLE
INSTRUCCIONES DE FUNCIONAMIENTO
CAT. #2460
INSTRUCCIONES PARA CARGAR LAS PILAS
Para asegurar el rendimiento a largo plazo de las
pilas, cárguelas durante 24 horas o más antes de
usarlas por primera vez.
“Carga rápida” Tiempo de carga- 3 a 4 horas
1. Inserte el enchufe del transformador de CA/CC en
el encastre del cargador (el encastre del transfor-
mador se encuentra en un compartimiento de la
base). Enchufe el transformador en el receptáculo
eléctrico. El indicador LED debe mostrar una luz
VERDE CONSTANTE.
2. Coloque la linterna en la base del cargador hasta
que quede fija. El indicador LED debe mostrar una
luz ROJA INTERMITENTE.
3. Cuando el indicador cambia a una luz VERDE
CONSTANTE quiere decir que la linterna está
completamente cargada y lista para usarse.
“Carga lenta” Tiempo de carga - 16 a 18 horas
(AUTOMOVIL, CASAS RODANTES, BARCOS)
1. Inserte el adaptador para el encendedor de cigar-
rillos No. de CAT. 8056 en el enchufe del vehículo
y conecte el transformador en la base de carga.
El indicador LED debe mostrar una luz VERDE
CONSTANTE.
2. Coloque la linterna en la base del cargador hasta que
quede fija. El indicador LED debe mostrar una luz ROJA.
ENCENDIDO / APAGADO
Para encender la linterna (con el extremo de la bombilla
apuntando en la dirección opuesta a usted), gire la palanca
del interruptor hacia la derecha hasta que se encienda.
Para apagarla, gire la palanca del interruptor hacia la
izquierda (con el extremo de la bombilla apuntando en
la dirección opuesta a usted), hasta que se apague.
INSTALACION DEL CONJUNTO DE PILAS
1. Retire el bastidor de la lente girándolo en sentido
contrario de las agujas del reloj.
2. Retire el módulo de la bombilla y el contacto.
3. Retire el conjunto las pilas usado y coloque el nuevo.
El conjunto de pilas tiene un borde de plástico que
asegura que sólo se instalen en la dirección correcta.
4. Vuelva a colocar el módulo de la bombilla y el contacto.
5. Vuelva a colocar el bastidor de la lente sobre la rosca
y gire en el sentido de las agujas del reloj al mismo
tiempo que ejerce un poco de presión sobre el mismo.
PILAS ALCALINAS (OPCION)
Inserte 4 pilas alcalinas tipo AA (2 en línea con el extremo
+ hacia arriba y dos en línea con el extremo + hacia abajo)
conforme a la polaridad indicada en la calcomanía que se
encuentra dentro del cuerpo de la linterna.
USO EN SUBMARINISMO (SCUBA)
Revise bien si hay cortes, rasguños o algún otro tipo
de daño en el anillo “O” o en la superficie de acople del
reborde del lente, ya que esto puede causar que la linterna
se llene de agua cuando esté bajo presión. Saque cualquier
depósito de sal, arena, polvo u otras substancias extrañas
de las superficies sellantes del anillo “O”. MANTENGA LAS
ROSCAS, LA RANURA DEL ANILLO “O” Y EL REBORDE
INTERIOR DEL LENTE LUBRICADOS CON GRASA DE
SILICONA.
REPLACEMENT PARTS
CAT # DESCRIPTION
2401 O-ring
8056 12v Plug In Charger Cord
2457 110v Transformer
2461 Handy Desk / Dash Smart Charger Base
2469 Replacement Battery
6061 Direct Wiring Rig
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to
Pelican Products Customer Service Department
(postage paid). Please call for a return authorization
number. Per our guarantee, Pelican Products will
replace or repair any broken or defective products.
Upon receipt of goods, Pelican Products will notify
you of any handling and return postage charges. If
your local retailer does not stock the above accessory
parts, you may order them directly from Pelican
Products. Send check or money order in U.S. dollars,
or order by phone using MasterCard or VISA (ask
for Customer Service). SORRY, NO C.O.D.’s. Subject
to sales tax. Allow 2-3 weeks delivery time. Pelican
Products pays postage and handling charges.
POSTAGE PAID FOR U.S. ZIP CODES ONLY.
Pelican Unconditional Lifetime
Guarantee of Excellence
If for any reason you are not satisfied with the quality
or performance of any PELICAN product, we will gladly
replace the product or refund your money (at your
option) within 30 days of purchase through the original
retailer/dealer. PELICAN PRODUCTS will continue to
guarantee the product directly for a lifetime against
breakage or defects in workmanship. Lifetime guarantee
does not cover the lamp or batteries. The o-rings must
be kept greased (and replaced if damaged) per product
instructions. This guarantee is void only if the PELICAN
product has been abused beyond normal and sensible
wear and tear.
THE ABOVE GUARANTEE DOES NOT COVER SHARKBITE,
BEAR ATTACK OR CHILDREN UNDER 5.
2463-311-000 © 2005 Pelican Products JL/05
23215 Early Ave. • Torrance, CA 90505
[phone] • FAX [phone] • www.pelican.com
PELICAN
Y o u break it, we replace it... forever.
SUBMERSIBLE
23215 Early Ave. • Torrance, CA 90505 USA
Tel [phone] • FAX [phone] • www.pelican.com
PELICANTM CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel [phone] • FAX [phone]
PELI TM PRODUCTS, S.A.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel [phone] • FAX [phone] • www.peli.com
All trademarks and logos displayed herein are registered and
unregistered trademarks of Pelican Products, Inc. and others.
PELICAN
Y o u break it, we replace it... forever.

PELICANTM
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
OPERATING INSTRUCTIONS
CHARGING INSTRUCTIONS
To ensure long term performance charge
battery for 24 hours or more before first use.
“Quick Charge” CHARGE TIME 3 TO 4 HRS.
1. Push the AC/DC Power Transformer plug into the
Charger Socket (the transformer socket is located in
a pocket in the base). Plug transformer into electri-
cal receptacle. The LED should be SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will pulse RED.
3. When the LED changes to SOLID GREEN the light
is fully charged and ready to use.
“Slow Charge” CHARGE TIME
16 TO 18 HOURS (CAR, RV OR BOAT)
1. Push the cigarette lighter adapter (CAT #8056)
into the vehicle’s socket and plug the transformer
into the charging base. The LED should be
SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will glow RED.
ON/OFF
Swing the switch lever to the right (light facing
away from you) until light activates. To turn light off,
swing the switch lever to the left (light facing away
from you) until the light goes off.
BATTERY PACK INSTALLATION
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp and contact module.
3. Remove used battery pack and replace with a
fresh battery pack. The battery pack has a plastic
rib to ensure that it can only be installed one way.
4. Replace the contact module and lamp.
5. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing slightly.
ALKALINE BATTERY (OPTION)
Insert 4 AA cell batteries (2 in-line with + end
up and 2 in-line + end down) as indicated on
polarity sticker located on the inside of the light.
SCUBA DIVING APPLICATION
Check closely for cuts, scratches, or an otherwise
damaged o-ring or mating lens lip surface as this
can cause the light to flood under pressure. Remove
any salt deposits, sand, dirt, or other foreign mat-
ter from the o-ring sealing surfaces. KEEP THE
THREADS, O-RING GROOVE AND INSIDE LIP OF
LENS LUBRICATED WITH SILICONE GREASE.
WARNING: Do not charge alkaline batteries.
LAMP REPLACEMENT
To replace the lamp module follow steps in
the battery installation section as listed below:
To remove lamp module follow steps #1 and #2.
To replace lamp module follow steps #4 and #5.
CAUTION:
If light is not to be used for some time, remove bat-
teries to prevent possible leakage and corrosion.
CHARGER BASE
MOUNTING INSTRUCTIONS
The charger base can be permanently mounted using
double sided tape (included) or with two
#8 screws (not included).
VEHICLE INSTALLATION
The charger base can be permanently mounted
in most vehicles and this operation should be
performed by a professional auto technician.
When installing the charger, ensure that the
DIRECT WIRING RIG is connected to an ignition key-
switch line.The high amperage draw of the charger
may drain the vehicle’s battery if
connected directly to the battery.
PRODUCT SPECIFICATIONS
Lamp Type: LED
Battery Burn Time: 32 hours
Battery Type:4.8V NiMH (4-cell)
Battery Brand: Use Pelican Cat. #2469
HYDROGEN GAS ABSORBER
Internal catalyst pellets, located on the lamp, are there
to help absorb hydrogen gas that could
possibly be emitted by defective, leaking, reversed
polarity or heavily discharged batteries. If the
pellets become lost or damaged, replace lamp imme-
diately. If pellets become wet, let them air dry. Pelican
Products assumes no liability for any brand of batteries
which are defective or cause injury to anyone when
used in any Pelican flashlight.
StealthLiteTM 24 60
RecoilTM LED
RECHARGEABLE
INSTRUCCIONES DE FUNCIONAMIENTO
CAT. #2460
INSTRUCCIONES PARA CARGAR LAS PILAS
Para asegurar el rendimiento a largo plazo de las
pilas, cárguelas durante 24 horas o más antes de
usarlas por primera vez.
“Carga rápida” Tiempo de carga- 3 a 4 horas
1. Inserte el enchufe del transformador de CA/CC en
el encastre del cargador (el encastre del transfor-
mador se encuentra en un compartimiento de la
base). Enchufe el transformador en el receptáculo
eléctrico. El indicador LED debe mostrar una luz
VERDE CONSTANTE.
2. Coloque la linterna en la base del cargador hasta
que quede fija. El indicador LED debe mostrar una
luz ROJA INTERMITENTE.
3. Cuando el indicador cambia a una luz VERDE
CONSTANTE quiere decir que la linterna está
completamente cargada y lista para usarse.
“Carga lenta” Tiempo de carga - 16 a 18 horas
(AUTOMOVIL, CASAS RODANTES, BARCOS)
1. Inserte el adaptador para el encendedor de cigar-
rillos No. de CAT. 8056 en el enchufe del vehículo
y conecte el transformador en la base de carga.
El indicador LED debe mostrar una luz VERDE
CONSTANTE.
2. Coloque la linterna en la base del cargador hasta que
quede fija. El indicador LED debe mostrar una luz ROJA.
ENCENDIDO / APAGADO
Para encender la linterna (con el extremo de la bombilla
apuntando en la dirección opuesta a usted), gire la palanca
del interruptor hacia la derecha hasta que se encienda.
Para apagarla, gire la palanca del interruptor hacia la
izquierda (con el extremo de la bombilla apuntando en
la dirección opuesta a usted), hasta que se apague.
INSTALACION DEL CONJUNTO DE PILAS
1. Retire el bastidor de la lente girándolo en sentido
contrario de las agujas del reloj.
2. Retire el módulo de la bombilla y el contacto.
3. Retire el conjunto las pilas usado y coloque el nuevo.
El conjunto de pilas tiene un borde de plástico que
asegura que sólo se instalen en la dirección correcta.
4. Vuelva a colocar el módulo de la bombilla y el contacto.
5. Vuelva a colocar el bastidor de la lente sobre la rosca
y gire en el sentido de las agujas del reloj al mismo
tiempo que ejerce un poco de presión sobre el mismo.
PILAS ALCALINAS (OPCION)
Inserte 4 pilas alcalinas tipo AA (2 en línea con el extremo
+ hacia arriba y dos en línea con el extremo + hacia abajo)
conforme a la polaridad indicada en la calcomanía que se
encuentra dentro del cuerpo de la linterna.
USO EN SUBMARINISMO (SCUBA)
Revise bien si hay cortes, rasguños o algún otro tipo
de daño en el anillo “O” o en la superficie de acople del
reborde del lente, ya que esto puede causar que la linterna
se llene de agua cuando esté bajo presión. Saque cualquier
depósito de sal, arena, polvo u otras substancias extrañas
de las superficies sellantes del anillo “O”. MANTENGA LAS
ROSCAS, LA RANURA DEL ANILLO “O” Y EL REBORDE
INTERIOR DEL LENTE LUBRICADOS CON GRASA DE
SILICONA.
REPLACEMENT PARTS
CAT # DESCRIPTION
2401 O-ring
8056 12v Plug In Charger Cord
2457 110v Transformer
2461 Handy Desk / Dash Smart Charger Base
2469 Replacement Battery
6061 Direct Wiring Rig
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to
Pelican Products Customer Service Department
(postage paid). Please call for a return authorization
number. Per our guarantee, Pelican Products will
replace or repair any broken or defective products.
Upon receipt of goods, Pelican Products will notify
you of any handling and return postage charges. If
your local retailer does not stock the above accessory
parts, you may order them directly from Pelican
Products. Send check or money order in U.S. dollars,
or order by phone using MasterCard or VISA (ask
for Customer Service). SORRY, NO C.O.D.’s. Subject
to sales tax. Allow 2-3 weeks delivery time. Pelican
Products pays postage and handling charges.
POSTAGE PAID FOR U.S. ZIP CODES ONLY.
Pelican Unconditional Lifetime
Guarantee of Excellence
If for any reason you are not satisfied with the quality
or performance of any PELICAN product, we will gladly
replace the product or refund your money (at your
option) within 30 days of purchase through the original
retailer/dealer. PELICAN PRODUCTS will continue to
guarantee the product directly for a lifetime against
breakage or defects in workmanship. Lifetime guarantee
does not cover the lamp or batteries. The o-rings must
be kept greased (and replaced if damaged) per product
instructions. This guarantee is void only if the PELICAN
product has been abused beyond normal and sensible
wear and tear.
THE ABOVE GUARANTEE DOES NOT COVER SHARKBITE,
BEAR ATTACK OR CHILDREN UNDER 5.
2463-311-000 © 2005 Pelican Products JL/05
23215 Early Ave. • Torrance, CA 90505
[phone] • FAX [phone] • www.pelican.com
PELICAN
Y o u break it, we replace it... forever.
SUBMERSIBLE
23215 Early Ave. • Torrance, CA 90505 USA
Tel [phone] • FAX [phone] • www.pelican.com
PELICANTM CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel [phone] • FAX [phone]
PELI TM PRODUCTS, S.A.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel [phone] • FAX [phone] • www.peli.com
All trademarks and logos displayed herein are registered and
unregistered trademarks of Pelican Products, Inc. and others.
PELICAN
Y o u break it, we replace it... forever.

PELICANTM
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
OPERATING INSTRUCTIONS
CHARGING INSTRUCTIONS
To ensure long term performance charge
battery for 24 hours or more before first use.
“Quick Charge” CHARGE TIME 3 TO 4 HRS.
1. Push the AC/DC Power Transformer plug into the
Charger Socket (the transformer socket is located in
a pocket in the base). Plug transformer into electri-
cal receptacle. The LED should be SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will pulse RED.
3. When the LED changes to SOLID GREEN the light
is fully charged and ready to use.
“Slow Charge” CHARGE TIME
16 TO 18 HOURS (CAR, RV OR BOAT)
1. Push the cigarette lighter adapter (CAT #8056)
into the vehicle’s socket and plug the transformer
into the charging base. The LED should be
SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will glow RED.
ON/OFF
Swing the switch lever to the right (light facing
away from you) until light activates. To turn light off,
swing the switch lever to the left (light facing away
from you) until the light goes off.
BATTERY PACK INSTALLATION
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp and contact module.
3. Remove used battery pack and replace with a
fresh battery pack. The battery pack has a plastic
rib to ensure that it can only be installed one way.
4. Replace the contact module and lamp.
5. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing slightly.
ALKALINE BATTERY (OPTION)
Insert 4 AA cell batteries (2 in-line with + end
up and 2 in-line + end down) as indicated on
polarity sticker located on the inside of the light.
SCUBA DIVING APPLICATION
Check closely for cuts, scratches, or an otherwise
damaged o-ring or mating lens lip surface as this
can cause the light to flood under pressure. Remove
any salt deposits, sand, dirt, or other foreign mat-
ter from the o-ring sealing surfaces. KEEP THE
THREADS, O-RING GROOVE AND INSIDE LIP OF
LENS LUBRICATED WITH SILICONE GREASE.
WARNING: Do not charge alkaline batteries.
LAMP REPLACEMENT
To replace the lamp module follow steps in
the battery installation section as listed below:
To remove lamp module follow steps #1 and #2.
To replace lamp module follow steps #4 and #5.
CAUTION:
If light is not to be used for some time, remove bat-
teries to prevent possible leakage and corrosion.
CHARGER BASE
MOUNTING INSTRUCTIONS
The charger base can be permanently mounted using
double sided tape (included) or with two
#8 screws (not included).
VEHICLE INSTALLATION
The charger base can be permanently mounted
in most vehicles and this operation should be
performed by a professional auto technician.
When installing the charger, ensure that the
DIRECT WIRING RIG is connected to an ignition key-
switch line.The high amperage draw of the charger
may drain the vehicle’s battery if
connected directly to the battery.
PRODUCT SPECIFICATIONS
Lamp Type: LED
Battery Burn Time: 32 hours
Battery Type:4.8V NiMH (4-cell)
Battery Brand: Use Pelican Cat. #2469
HYDROGEN GAS ABSORBER
Internal catalyst pellets, located on the lamp, are there
to help absorb hydrogen gas that could
possibly be emitted by defective, leaking, reversed
polarity or heavily discharged batteries. If the
pellets become lost or damaged, replace lamp imme-
diately. If pellets become wet, let them air dry. Pelican
Products assumes no liability for any brand of batteries
which are defective or cause injury to anyone when
used in any Pelican flashlight.
StealthLiteTM 24 60
RecoilTM LED
RECHARGEABLE
INSTRUCCIONES DE FUNCIONAMIENTO
CAT. #2460
INSTRUCCIONES PARA CARGAR LAS PILAS
Para asegurar el rendimiento a largo plazo de las
pilas, cárguelas durante 24 horas o más antes de
usarlas por primera vez.
“Carga rápida” Tiempo de carga- 3 a 4 horas
1. Inserte el enchufe del transformador de CA/CC en
el encastre del cargador (el encastre del transfor-
mador se encuentra en un compartimiento de la
base). Enchufe el transformador en el receptáculo
eléctrico. El indicador LED debe mostrar una luz
VERDE CONSTANTE.
2. Coloque la linterna en la base del cargador hasta
que quede fija. El indicador LED debe mostrar una
luz ROJA INTERMITENTE.
3. Cuando el indicador cambia a una luz VERDE
CONSTANTE quiere decir que la linterna está
completamente cargada y lista para usarse.
“Carga lenta” Tiempo de carga - 16 a 18 horas
(AUTOMOVIL, CASAS RODANTES, BARCOS)
1. Inserte el adaptador para el encendedor de cigar-
rillos No. de CAT. 8056 en el enchufe del vehículo
y conecte el transformador en la base de carga.
El indicador LED debe mostrar una luz VERDE
CONSTANTE.
2. Coloque la linterna en la base del cargador hasta que
quede fija. El indicador LED debe mostrar una luz ROJA.
ENCENDIDO / APAGADO
Para encender la linterna (con el extremo de la bombilla
apuntando en la dirección opuesta a usted), gire la palanca
del interruptor hacia la derecha hasta que se encienda.
Para apagarla, gire la palanca del interruptor hacia la
izquierda (con el extremo de la bombilla apuntando en
la dirección opuesta a usted), hasta que se apague.
INSTALACION DEL CONJUNTO DE PILAS
1. Retire el bastidor de la lente girándolo en sentido
contrario de las agujas del reloj.
2. Retire el módulo de la bombilla y el contacto.
3. Retire el conjunto las pilas usado y coloque el nuevo.
El conjunto de pilas tiene un borde de plástico que
asegura que sólo se instalen en la dirección correcta.
4. Vuelva a colocar el módulo de la bombilla y el contacto.
5. Vuelva a colocar el bastidor de la lente sobre la rosca
y gire en el sentido de las agujas del reloj al mismo
tiempo que ejerce un poco de presión sobre el mismo.
PILAS ALCALINAS (OPCION)
Inserte 4 pilas alcalinas tipo AA (2 en línea con el extremo
+ hacia arriba y dos en línea con el extremo + hacia abajo)
conforme a la polaridad indicada en la calcomanía que se
encuentra dentro del cuerpo de la linterna.
USO EN SUBMARINISMO (SCUBA)
Revise bien si hay cortes, rasguños o algún otro tipo
de daño en el anillo “O” o en la superficie de acople del
reborde del lente, ya que esto puede causar que la linterna
se llene de agua cuando esté bajo presión. Saque cualquier
depósito de sal, arena, polvo u otras substancias extrañas
de las superficies sellantes del anillo “O”. MANTENGA LAS
ROSCAS, LA RANURA DEL ANILLO “O” Y EL REBORDE
INTERIOR DEL LENTE LUBRICADOS CON GRASA DE
SILICONA.
REPLACEMENT PARTS
CAT # DESCRIPTION
2401 O-ring
8056 12v Plug In Charger Cord
2457 110v Transformer
2461 Handy Desk / Dash Smart Charger Base
2469 Replacement Battery
6061 Direct Wiring Rig
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to
Pelican Products Customer Service Department
(postage paid). Please call for a return authorization
number. Per our guarantee, Pelican Products will
replace or repair any broken or defective products.
Upon receipt of goods, Pelican Products will notify
you of any handling and return postage charges. If
your local retailer does not stock the above accessory
parts, you may order them directly from Pelican
Products. Send check or money order in U.S. dollars,
or order by phone using MasterCard or VISA (ask
for Customer Service). SORRY, NO C.O.D.’s. Subject
to sales tax. Allow 2-3 weeks delivery time. Pelican
Products pays postage and handling charges.
POSTAGE PAID FOR U.S. ZIP CODES ONLY.
Pelican Unconditional Lifetime
Guarantee of Excellence
If for any reason you are not satisfied with the quality
or performance of any PELICAN product, we will gladly
replace the product or refund your money (at your
option) within 30 days of purchase through the original
retailer/dealer. PELICAN PRODUCTS will continue to
guarantee the product directly for a lifetime against
breakage or defects in workmanship. Lifetime guarantee
does not cover the lamp or batteries. The o-rings must
be kept greased (and replaced if damaged) per product
instructions. This guarantee is void only if the PELICAN
product has been abused beyond normal and sensible
wear and tear.
THE ABOVE GUARANTEE DOES NOT COVER SHARKBITE,
BEAR ATTACK OR CHILDREN UNDER 5.
2463-311-000 © 2005 Pelican Products JL/05
23215 Early Ave. • Torrance, CA 90505
[phone] • FAX [phone] • www.pelican.com
PELICAN
Y o u break it, we replace it... forever.
SUBMERSIBLE
23215 Early Ave. • Torrance, CA 90505 USA
Tel [phone] • FAX [phone] • www.pelican.com
PELICANTM CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel [phone] • FAX [phone]
PELI TM PRODUCTS, S.A.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel [phone] • FAX [phone] • www.peli.com
All trademarks and logos displayed herein are registered and
unregistered trademarks of Pelican Products, Inc. and others.
PELICAN
Y o u break it, we replace it... forever.

PELICANTM
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
OPERATING INSTRUCTIONS
CHARGING INSTRUCTIONS
To ensure long term performance charge
battery for 24 hours or more before first use.
“Quick Charge” CHARGE TIME 3 TO 4 HRS.
1. Push the AC/DC Power Transformer plug into the
Charger Socket (the transformer socket is located in
a pocket in the base). Plug transformer into electri-
cal receptacle. The LED should be SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will pulse RED.
3. When the LED changes to SOLID GREEN the light
is fully charged and ready to use.
“Slow Charge” CHARGE TIME
16 TO 18 HOURS (CAR, RV OR BOAT)
1. Push the cigarette lighter adapter (CAT #8056)
into the vehicle’s socket and plug the transformer
into the charging base. The LED should be
SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will glow RED.
ON/OFF
Swing the switch lever to the right (light facing
away from you) until light activates. To turn light off,
swing the switch lever to the left (light facing away
from you) until the light goes off.
BATTERY PACK INSTALLATION
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp and contact module.
3. Remove used battery pack and replace with a
fresh battery pack. The battery pack has a plastic
rib to ensure that it can only be installed one way.
4. Replace the contact module and lamp.
5. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing slightly.
ALKALINE BATTERY (OPTION)
Insert 4 AA cell batteries (2 in-line with + end
up and 2 in-line + end down) as indicated on
polarity sticker located on the inside of the light.
SCUBA DIVING APPLICATION
Check closely for cuts, scratches, or an otherwise
damaged o-ring or mating lens lip surface as this
can cause the light to flood under pressure. Remove
any salt deposits, sand, dirt, or other foreign mat-
ter from the o-ring sealing surfaces. KEEP THE
THREADS, O-RING GROOVE AND INSIDE LIP OF
LENS LUBRICATED WITH SILICONE GREASE.
WARNING: Do not charge alkaline batteries.
LAMP REPLACEMENT
To replace the lamp module follow steps in
the battery installation section as listed below:
To remove lamp module follow steps #1 and #2.
To replace lamp module follow steps #4 and #5.
CAUTION:
If light is not to be used for some time, remove bat-
teries to prevent possible leakage and corrosion.
CHARGER BASE
MOUNTING INSTRUCTIONS
The charger base can be permanently mounted using
double sided tape (included) or with two
#8 screws (not included).
VEHICLE INSTALLATION
The charger base can be permanently mounted
in most vehicles and this operation should be
performed by a professional auto technician.
When installing the charger, ensure that the
DIRECT WIRING RIG is connected to an ignition key-
switch line.The high amperage draw of the charger
may drain the vehicle’s battery if
connected directly to the battery.
PRODUCT SPECIFICATIONS
Lamp Type: LED
Battery Burn Time: 32 hours
Battery Type:4.8V NiMH (4-cell)
Battery Brand: Use Pelican Cat. #2469
HYDROGEN GAS ABSORBER
Internal catalyst pellets, located on the lamp, are there
to help absorb hydrogen gas that could
possibly be emitted by defective, leaking, reversed
polarity or heavily discharged batteries. If the
pellets become lost or damaged, replace lamp imme-
diately. If pellets become wet, let them air dry. Pelican
Products assumes no liability for any brand of batteries
which are defective or cause injury to anyone when
used in any Pelican flashlight.
StealthLiteTM 24 60
RecoilTM LED
RECHARGEABLE
INSTRUCCIONES DE FUNCIONAMIENTO
CAT. #2460
INSTRUCCIONES PARA CARGAR LAS PILAS
Para asegurar el rendimiento a largo plazo de las
pilas, cárguelas durante 24 horas o más antes de
usarlas por primera vez.
“Carga rápida” Tiempo de carga- 3 a 4 horas
1. Inserte el enchufe del transformador de CA/CC en
el encastre del cargador (el encastre del transfor-
mador se encuentra en un compartimiento de la
base). Enchufe el transformador en el receptáculo
eléctrico. El indicador LED debe mostrar una luz
VERDE CONSTANTE.
2. Coloque la linterna en la base del cargador hasta
que quede fija. El indicador LED debe mostrar una
luz ROJA INTERMITENTE.
3. Cuando el indicador cambia a una luz VERDE
CONSTANTE quiere decir que la linterna está
completamente cargada y lista para usarse.
“Carga lenta” Tiempo de carga - 16 a 18 horas
(AUTOMOVIL, CASAS RODANTES, BARCOS)
1. Inserte el adaptador para el encendedor de cigar-
rillos No. de CAT. 8056 en el enchufe del vehículo
y conecte el transformador en la base de carga.
El indicador LED debe mostrar una luz VERDE
CONSTANTE.
2. Coloque la linterna en la base del cargador hasta que
quede fija. El indicador LED debe mostrar una luz ROJA.
ENCENDIDO / APAGADO
Para encender la linterna (con el extremo de la bombilla
apuntando en la dirección opuesta a usted), gire la palanca
del interruptor hacia la derecha hasta que se encienda.
Para apagarla, gire la palanca del interruptor hacia la
izquierda (con el extremo de la bombilla apuntando en
la dirección opuesta a usted), hasta que se apague.
INSTALACION DEL CONJUNTO DE PILAS
1. Retire el bastidor de la lente girándolo en sentido
contrario de las agujas del reloj.
2. Retire el módulo de la bombilla y el contacto.
3. Retire el conjunto las pilas usado y coloque el nuevo.
El conjunto de pilas tiene un borde de plástico que
asegura que sólo se instalen en la dirección correcta.
4. Vuelva a colocar el módulo de la bombilla y el contacto.
5. Vuelva a colocar el bastidor de la lente sobre la rosca
y gire en el sentido de las agujas del reloj al mismo
tiempo que ejerce un poco de presión sobre el mismo.
PILAS ALCALINAS (OPCION)
Inserte 4 pilas alcalinas tipo AA (2 en línea con el extremo
+ hacia arriba y dos en línea con el extremo + hacia abajo)
conforme a la polaridad indicada en la calcomanía que se
encuentra dentro del cuerpo de la linterna.
USO EN SUBMARINISMO (SCUBA)
Revise bien si hay cortes, rasguños o algún otro tipo
de daño en el anillo “O” o en la superficie de acople del
reborde del lente, ya que esto puede causar que la linterna
se llene de agua cuando esté bajo presión. Saque cualquier
depósito de sal, arena, polvo u otras substancias extrañas
de las superficies sellantes del anillo “O”. MANTENGA LAS
ROSCAS, LA RANURA DEL ANILLO “O” Y EL REBORDE
INTERIOR DEL LENTE LUBRICADOS CON GRASA DE
SILICONA.
REPLACEMENT PARTS
CAT # DESCRIPTION
2401 O-ring
8056 12v Plug In Charger Cord
2457 110v Transformer
2461 Handy Desk / Dash Smart Charger Base
2469 Replacement Battery
6061 Direct Wiring Rig
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to
Pelican Products Customer Service Department
(postage paid). Please call for a return authorization
number. Per our guarantee, Pelican Products will
replace or repair any broken or defective products.
Upon receipt of goods, Pelican Products will notify
you of any handling and return postage charges. If
your local retailer does not stock the above accessory
parts, you may order them directly from Pelican
Products. Send check or money order in U.S. dollars,
or order by phone using MasterCard or VISA (ask
for Customer Service). SORRY, NO C.O.D.’s. Subject
to sales tax. Allow 2-3 weeks delivery time. Pelican
Products pays postage and handling charges.
POSTAGE PAID FOR U.S. ZIP CODES ONLY.
Pelican Unconditional Lifetime
Guarantee of Excellence
If for any reason you are not satisfied with the quality
or performance of any PELICAN product, we will gladly
replace the product or refund your money (at your
option) within 30 days of purchase through the original
retailer/dealer. PELICAN PRODUCTS will continue to
guarantee the product directly for a lifetime against
breakage or defects in workmanship. Lifetime guarantee
does not cover the lamp or batteries. The o-rings must
be kept greased (and replaced if damaged) per product
instructions. This guarantee is void only if the PELICAN
product has been abused beyond normal and sensible
wear and tear.
THE ABOVE GUARANTEE DOES NOT COVER SHARKBITE,
BEAR ATTACK OR CHILDREN UNDER 5.
2463-311-000 © 2005 Pelican Products JL/05
23215 Early Ave. • Torrance, CA 90505
[phone] • FAX [phone] • www.pelican.com
PELICAN
Y o u break it, we replace it... forever.
SUBMERSIBLE
23215 Early Ave. • Torrance, CA 90505 USA
Tel [phone] • FAX [phone] • www.pelican.com
PELICANTM CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel [phone] • FAX [phone]
PELI TM PRODUCTS, S.A.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel [phone] • FAX [phone] • www.peli.com
All trademarks and logos displayed herein are registered and
unregistered trademarks of Pelican Products, Inc. and others.
PELICAN
Y o u break it, we replace it... forever.

PELICANTM
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
OPERATING INSTRUCTIONS
CHARGING INSTRUCTIONS
To ensure long term performance charge
battery for 24 hours or more before first use.
“Quick Charge” CHARGE TIME 3 TO 4 HRS.
1. Push the AC/DC Power Transformer plug into the
Charger Socket (the transformer socket is located in
a pocket in the base). Plug transformer into electri-
cal receptacle. The LED should be SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will pulse RED.
3. When the LED changes to SOLID GREEN the light
is fully charged and ready to use.
“Slow Charge” CHARGE TIME
16 TO 18 HOURS (CAR, RV OR BOAT)
1. Push the cigarette lighter adapter (CAT #8056)
into the vehicle’s socket and plug the transformer
into the charging base. The LED should be
SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will glow RED.
ON/OFF
Swing the switch lever to the right (light facing
away from you) until light activates. To turn light off,
swing the switch lever to the left (light facing away
from you) until the light goes off.
BATTERY PACK INSTALLATION
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp and contact module.
3. Remove used battery pack and replace with a
fresh battery pack. The battery pack has a plastic
rib to ensure that it can only be installed one way.
4. Replace the contact module and lamp.
5. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing slightly.
ALKALINE BATTERY (OPTION)
Insert 4 AA cell batteries (2 in-line with + end
up and 2 in-line + end down) as indicated on
polarity sticker located on the inside of the light.
SCUBA DIVING APPLICATION
Check closely for cuts, scratches, or an otherwise
damaged o-ring or mating lens lip surface as this
can cause the light to flood under pressure. Remove
any salt deposits, sand, dirt, or other foreign mat-
ter from the o-ring sealing surfaces. KEEP THE
THREADS, O-RING GROOVE AND INSIDE LIP OF
LENS LUBRICATED WITH SILICONE GREASE.
WARNING: Do not charge alkaline batteries.
LAMP REPLACEMENT
To replace the lamp module follow steps in
the battery installation section as listed below:
To remove lamp module follow steps #1 and #2.
To replace lamp module follow steps #4 and #5.
CAUTION:
If light is not to be used for some time, remove bat-
teries to prevent possible leakage and corrosion.
CHARGER BASE
MOUNTING INSTRUCTIONS
The charger base can be permanently mounted using
double sided tape (included) or with two
#8 screws (not included).
VEHICLE INSTALLATION
The charger base can be permanently mounted
in most vehicles and this operation should be
performed by a professional auto technician.
When installing the charger, ensure that the
DIRECT WIRING RIG is connected to an ignition key-
switch line.The high amperage draw of the charger
may drain the vehicle’s battery if
connected directly to the battery.
PRODUCT SPECIFICATIONS
Lamp Type: LED
Battery Burn Time: 32 hours
Battery Type:4.8V NiMH (4-cell)
Battery Brand: Use Pelican Cat. #2469
HYDROGEN GAS ABSORBER
Internal catalyst pellets, located on the lamp, are there
to help absorb hydrogen gas that could
possibly be emitted by defective, leaking, reversed
polarity or heavily discharged batteries. If the
pellets become lost or damaged, replace lamp imme-
diately. If pellets become wet, let them air dry. Pelican
Products assumes no liability for any brand of batteries
which are defective or cause injury to anyone when
used in any Pelican flashlight.
StealthLiteTM 24 60
RecoilTM LED
RECHARGEABLE
INSTRUCCIONES DE FUNCIONAMIENTO
CAT. #2460
INSTRUCCIONES PARA CARGAR LAS PILAS
Para asegurar el rendimiento a largo plazo de las
pilas, cárguelas durante 24 horas o más antes de
usarlas por primera vez.
“Carga rápida” Tiempo de carga- 3 a 4 horas
1. Inserte el enchufe del transformador de CA/CC en
el encastre del cargador (el encastre del transfor-
mador se encuentra en un compartimiento de la
base). Enchufe el transformador en el receptáculo
eléctrico. El indicador LED debe mostrar una luz
VERDE CONSTANTE.
2. Coloque la linterna en la base del cargador hasta
que quede fija. El indicador LED debe mostrar una
luz ROJA INTERMITENTE.
3. Cuando el indicador cambia a una luz VERDE
CONSTANTE quiere decir que la linterna está
completamente cargada y lista para usarse.
“Carga lenta” Tiempo de carga - 16 a 18 horas
(AUTOMOVIL, CASAS RODANTES, BARCOS)
1. Inserte el adaptador para el encendedor de cigar-
rillos No. de CAT. 8056 en el enchufe del vehículo
y conecte el transformador en la base de carga.
El indicador LED debe mostrar una luz VERDE
CONSTANTE.
2. Coloque la linterna en la base del cargador hasta que
quede fija. El indicador LED debe mostrar una luz ROJA.
ENCENDIDO / APAGADO
Para encender la linterna (con el extremo de la bombilla
apuntando en la dirección opuesta a usted), gire la palanca
del interruptor hacia la derecha hasta que se encienda.
Para apagarla, gire la palanca del interruptor hacia la
izquierda (con el extremo de la bombilla apuntando en
la dirección opuesta a usted), hasta que se apague.
INSTALACION DEL CONJUNTO DE PILAS
1. Retire el bastidor de la lente girándolo en sentido
contrario de las agujas del reloj.
2. Retire el módulo de la bombilla y el contacto.
3. Retire el conjunto las pilas usado y coloque el nuevo.
El conjunto de pilas tiene un borde de plástico que
asegura que sólo se instalen en la dirección correcta.
4. Vuelva a colocar el módulo de la bombilla y el contacto.
5. Vuelva a colocar el bastidor de la lente sobre la rosca
y gire en el sentido de las agujas del reloj al mismo
tiempo que ejerce un poco de presión sobre el mismo.
PILAS ALCALINAS (OPCION)
Inserte 4 pilas alcalinas tipo AA (2 en línea con el extremo
+ hacia arriba y dos en línea con el extremo + hacia abajo)
conforme a la polaridad indicada en la calcomanía que se
encuentra dentro del cuerpo de la linterna.
USO EN SUBMARINISMO (SCUBA)
Revise bien si hay cortes, rasguños o algún otro tipo
de daño en el anillo “O” o en la superficie de acople del
reborde del lente, ya que esto puede causar que la linterna
se llene de agua cuando esté bajo presión. Saque cualquier
depósito de sal, arena, polvo u otras substancias extrañas
de las superficies sellantes del anillo “O”. MANTENGA LAS
ROSCAS, LA RANURA DEL ANILLO “O” Y EL REBORDE
INTERIOR DEL LENTE LUBRICADOS CON GRASA DE
SILICONA.
REPLACEMENT PARTS
CAT # DESCRIPTION
2401 O-ring
8056 12v Plug In Charger Cord
2457 110v Transformer
2461 Handy Desk / Dash Smart Charger Base
2469 Replacement Battery
6061 Direct Wiring Rig
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to
Pelican Products Customer Service Department
(postage paid). Please call for a return authorization
number. Per our guarantee, Pelican Products will
replace or repair any broken or defective products.
Upon receipt of goods, Pelican Products will notify
you of any handling and return postage charges. If
your local retailer does not stock the above accessory
parts, you may order them directly from Pelican
Products. Send check or money order in U.S. dollars,
or order by phone using MasterCard or VISA (ask
for Customer Service). SORRY, NO C.O.D.’s. Subject
to sales tax. Allow 2-3 weeks delivery time. Pelican
Products pays postage and handling charges.
POSTAGE PAID FOR U.S. ZIP CODES ONLY.
Pelican Unconditional Lifetime
Guarantee of Excellence
If for any reason you are not satisfied with the quality
or performance of any PELICAN product, we will gladly
replace the product or refund your money (at your
option) within 30 days of purchase through the original
retailer/dealer. PELICAN PRODUCTS will continue to
guarantee the product directly for a lifetime against
breakage or defects in workmanship. Lifetime guarantee
does not cover the lamp or batteries. The o-rings must
be kept greased (and replaced if damaged) per product
instructions. This guarantee is void only if the PELICAN
product has been abused beyond normal and sensible
wear and tear.
THE ABOVE GUARANTEE DOES NOT COVER SHARKBITE,
BEAR ATTACK OR CHILDREN UNDER 5.
2463-311-000 © 2005 Pelican Products JL/05
23215 Early Ave. • Torrance, CA 90505
[phone] • FAX [phone] • www.pelican.com
PELICAN
Y o u break it, we replace it... forever.
SUBMERSIBLE
23215 Early Ave. • Torrance, CA 90505 USA
Tel [phone] • FAX [phone] • www.pelican.com
PELICANTM CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel [phone] • FAX [phone]
PELI TM PRODUCTS, S.A.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel [phone] • FAX [phone] • www.peli.com
All trademarks and logos displayed herein are registered and
unregistered trademarks of Pelican Products, Inc. and others.
PELICAN
Y o u break it, we replace it... forever.

PELICANTM
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
StealthLiteTM 2460
RecoilTM LED
RECHARGEABLE
OPERATING INSTRUCTIONS
CHARGING INSTRUCTIONS
To ensure long term performance charge
battery for 24 hours or more before first use.
“Quick Charge” CHARGE TIME 3 TO 4 HRS.
1. Push the AC/DC Power Transformer plug into the
Charger Socket (the transformer socket is located in
a pocket in the base). Plug transformer into electri-
cal receptacle. The LED should be SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will pulse RED.
3. When the LED changes to SOLID GREEN the light
is fully charged and ready to use.
“Slow Charge” CHARGE TIME
16 TO 18 HOURS (CAR, RV OR BOAT)
1. Push the cigarette lighter adapter (CAT #8056)
into the vehicle’s socket and plug the transformer
into the charging base. The LED should be
SOLID GREEN.
2. Insert the flashlight into charger base until locked
in position. The LED will glow RED.
ON/OFF
Swing the switch lever to the right (light facing
away from you) until light activates. To turn light off,
swing the switch lever to the left (light facing away
from you) until the light goes off.
BATTERY PACK INSTALLATION
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp and contact module.
3. Remove used battery pack and replace with a
fresh battery pack. The battery pack has a plastic
rib to ensure that it can only be installed one way.
4. Replace the contact module and lamp.
5. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing slightly.
ALKALINE BATTERY (OPTION)
Insert 4 AA cell batteries (2 in-line with + end
up and 2 in-line + end down) as indicated on
polarity sticker located on the inside of the light.
SCUBA DIVING APPLICATION
Check closely for cuts, scratches, or an otherwise
damaged o-ring or mating lens lip surface as this
can cause the light to flood under pressure. Remove
any salt deposits, sand, dirt, or other foreign mat-
ter from the o-ring sealing surfaces. KEEP THE
THREADS, O-RING GROOVE AND INSIDE LIP OF
LENS LUBRICATED WITH SILICONE GREASE.
WARNING: Do not charge alkaline batteries.
LAMP REPLACEMENT
To replace the lamp module follow steps in
the battery installation section as listed below:
To remove lamp module follow steps #1 and #2.
To replace lamp module follow steps #4 and #5.
CAUTION:
If light is not to be used for some time, remove bat-
teries to prevent possible leakage and corrosion.
CHARGER BASE
MOUNTING INSTRUCTIONS
The charger base can be permanently mounted using
double sided tape (included) or with two
#8 screws (not included).
VEHICLE INSTALLATION
The charger base can be permanently mounted
in most vehicles and this operation should be
performed by a professional auto technician.
When installing the charger, ensure that the
DIRECT WIRING RIG is connected to an ignition key-
switch line.The high amperage draw of the charger
may drain the vehicle’s battery if
connected directly to the battery.
PRODUCT SPECIFICATIONS
Lamp Type: LED
Battery Burn Time: 32 hours
Battery Type:4.8V NiMH (4-cell)
Battery Brand: Use Pelican Cat. #2469
HYDROGEN GAS ABSORBER
Internal catalyst pellets, located on the lamp, are there
to help absorb hydrogen gas that could
possibly be emitted by defective, leaking, reversed
polarity or heavily discharged batteries. If the
pellets become lost or damaged, replace lamp imme-
diately. If pellets become wet, let them air dry. Pelican
Products assumes no liability for any brand of batteries
which are defective or cause injury to anyone when
used in any Pelican flashlight.
StealthLiteTM 24 60
RecoilTM LED
RECHARGEABLE
INSTRUCCIONES DE FUNCIONAMIENTO
CAT. #2460
INSTRUCCIONES PARA CARGAR LAS PILAS
Para asegurar el rendimiento a largo plazo de las
pilas, cárguelas durante 24 horas o más antes de
usarlas por primera vez.
“Carga rápida” Tiempo de carga- 3 a 4 horas
1. Inserte el enchufe del transformador de CA/CC en
el encastre del cargador (el encastre del transfor-
mador se encuentra en un compartimiento de la
base). Enchufe el transformador en el receptáculo
eléctrico. El indicador LED debe mostrar una luz
VERDE CONSTANTE.
2. Coloque la linterna en la base del cargador hasta
que quede fija. El indicador LED debe mostrar una
luz ROJA INTERMITENTE.
3. Cuando el indicador cambia a una luz VERDE
CONSTANTE quiere decir que la linterna está
completamente cargada y lista para usarse.
“Carga lenta” Tiempo de carga - 16 a 18 horas
(AUTOMOVIL, CASAS RODANTES, BARCOS)
1. Inserte el adaptador para el encendedor de cigar-
rillos No. de CAT. 8056 en el enchufe del vehículo
y conecte el transformador en la base de carga.
El indicador LED debe mostrar una luz VERDE
CONSTANTE.
2. Coloque la linterna en la base del cargador hasta que
quede fija. El indicador LED debe mostrar una luz ROJA.
ENCENDIDO / APAGADO
Para encender la linterna (con el extremo de la bombilla
apuntando en la dirección opuesta a usted), gire la palanca
del interruptor hacia la derecha hasta que se encienda.
Para apagarla, gire la palanca del interruptor hacia la
izquierda (con el extremo de la bombilla apuntando en
la dirección opuesta a usted), hasta que se apague.
INSTALACION DEL CONJUNTO DE PILAS
1. Retire el bastidor de la lente girándolo en sentido
contrario de las agujas del reloj.
2. Retire el módulo de la bombilla y el contacto.
3. Retire el conjunto las pilas usado y coloque el nuevo.
El conjunto de pilas tiene un borde de plástico que
asegura que sólo se instalen en la dirección correcta.
4. Vuelva a colocar el módulo de la bombilla y el contacto.
5. Vuelva a colocar el bastidor de la lente sobre la rosca
y gire en el sentido de las agujas del reloj al mismo
tiempo que ejerce un poco de presión sobre el mismo.
PILAS ALCALINAS (OPCION)
Inserte 4 pilas alcalinas tipo AA (2 en línea con el extremo
+ hacia arriba y dos en línea con el extremo + hacia abajo)
conforme a la polaridad indicada en la calcomanía que se
encuentra dentro del cuerpo de la linterna.
USO EN SUBMARINISMO (SCUBA)
Revise bien si hay cortes, rasguños o algún otro tipo
de daño en el anillo “O” o en la superficie de acople del
reborde del lente, ya que esto puede causar que la linterna
se llene de agua cuando esté bajo presión. Saque cualquier
depósito de sal, arena, polvo u otras substancias extrañas
de las superficies sellantes del anillo “O”. MANTENGA LAS
ROSCAS, LA RANURA DEL ANILLO “O” Y EL REBORDE
INTERIOR DEL LENTE LUBRICADOS CON GRASA DE
SILICONA.
REPLACEMENT PARTS
CAT # DESCRIPTION
2401 O-ring
8056 12v Plug In Charger Cord
2457 110v Transformer
2461 Handy Desk / Dash Smart Charger Base
2469 Replacement Battery
6061 Direct Wiring Rig
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to
Pelican Products Customer Service Department
(postage paid). Please call for a return authorization
number. Per our guarantee, Pelican Products will
replace or repair any broken or defective products.
Upon receipt of goods, Pelican Products will notify
you of any handling and return postage charges. If
your local retailer does not stock the above accessory
parts, you may order them directly from Pelican
Products. Send check or money order in U.S. dollars,
or order by phone using MasterCard or VISA (ask
for Customer Service). SORRY, NO C.O.D.’s. Subject
to sales tax. Allow 2-3 weeks delivery time. Pelican
Products pays postage and handling charges.
POSTAGE PAID FOR U.S. ZIP CODES ONLY.
Pelican Unconditional Lifetime
Guarantee of Excellence
If for any reason you are not satisfied with the quality
or performance of any PELICAN product, we will gladly
replace the product or refund your money (at your
option) within 30 days of purchase through the original
retailer/dealer. PELICAN PRODUCTS will continue to
guarantee the product directly for a lifetime against
breakage or defects in workmanship. Lifetime guarantee
does not cover the lamp or batteries. The o-rings must
be kept greased (and replaced if damaged) per product
instructions. This guarantee is void only if the PELICAN
product has been abused beyond normal and sensible
wear and tear.
THE ABOVE GUARANTEE DOES NOT COVER SHARKBITE,
BEAR ATTACK OR CHILDREN UNDER 5.
2463-311-000 © 2005 Pelican Products JL/05
23215 Early Ave. • Torrance, CA 90505
[phone] • FAX [phone] • www.pelican.com
PELICAN
Y o u break it, we replace it... forever.
SUBMERSIBLE
23215 Early Ave. • Torrance, CA 90505 USA
Tel [phone] • FAX [phone] • www.pelican.com
PELICANTM CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel [phone] • FAX [phone]
PELI TM PRODUCTS, S.A.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel [phone] • FAX [phone] • www.peli.com
All trademarks and logos displayed herein are registered and
unregistered trademarks of Pelican Products, Inc. and others.
PELICAN
Y o u break it, we replace it... forever.