Pepperl+Fuchs OIT500-F113-B17-CB User manual

R
OIT500-F113-B17-CB
High-Temperature
Identification Sy tem
Manual

With regard to the supply of products, the current issue of the following document is applicable: The
General Terms of Delivery for Products and Services of the Electrical ndustry, published by the Central
Association of the Electrical ndustry (Zentralverband Elektrotechnik und Elektroindustrie (ZVE ) e.V.)
in its most recent version as well as the supplementary clause: "Expanded reservation of proprietor-
ship"
Worldwide
Pepperl+Fuchs Group
Lilienthalstr. 200
68307 Mannheim
Germany
Phone: [phone] - 0
E-mail: [e-mail]
North American Headquarter
Pepperl+Fuchs nc.
1600 Enterprise Parkway
Twinsburg, Ohio 44087
USA
Phone: [phone]
E-mail: [e-mail]
A ia Headquarter
Pepperl+Fuchs Pte. Ltd.
P+F Building
18 Ayer Rajah Crescent
Singapore 139942
Phone: [phone]
E-mail: [e-mail]
https://www.pepperl-fuchs.com

3
O T500-F113-B17-CB
Contents
2019-12
1 Introduction................................................................................................................ 5
1.1 Content of thi Document............................................................................. 5
1.2 Target Group, Per onnel ............................................................................... 5
1.3 Symbol U ed ................................................................................................ 6
1.4 Regi tered Trademark ................................................................................. 6
2 Product De cription .................................................................................................. 7
2.1 Functional De cription ..................................................................................7
2.2 Application and Area of U e....................................................................... 7
2.3 LED Indicator ................................................................................................. 8
2.4 Interface and Connection ....................................................................... 10
2.5 Scope of Delivery......................................................................................... 12
2.6 Acce orie .................................................................................................. 13
2.6.1 Power Supply................................................................................... 13
2.6.2 Connection Cable for Trigger Sensors and External Lighting ........... 13
2.6.3 Network Cable ................................................................................. 14
2.6.4 Code Sheets.................................................................................... 15
3 Mounting and In tallation....................................................................................... 17
3.1 OIT Sy tem Overview .................................................................................. 17
3.2 Mounting the OIT Sy tem............................................................................ 18
3.2.1 Operating Distance.......................................................................... 18
3.2.2 Setting the Lighting Angle ................................................................ 21
3.2.3 Mounting the Device........................................................................ 23
3.2.4 Mounting the Code Sheet ................................................................ 24
3.3 E tabli hing an Electrical Connection ...................................................... 25
3.4 Setting up Window Network Communication between the Device
and a PC/Laptop .......................................................................................... 27
3.5 Connecting the OIT Sy tem with Vi ion Configurator ............................. 31
4 Commi ioning........................................................................................................ 32
4.1 Integrating the OIT Sy tem into the Network............................................32
4.2 Parameterization.......................................................................................... 41

O T500-F113-B17-CB
Contents
4
2019-12
5 Parameterization U ing Vi ion Configurator.........................................................45
5.1 Screen Layout ..............................................................................................46
5.2 Menu Bar.......................................................................................................47
5.2.1 File Menu ......................................................................................... 47
5.2.2 View Menu .......................................................................................47
5.2.3 Sensor Menu....................................................................................48
5.2.4 mage Menu .....................................................................................49
5.2.5 Administration Menu ........................................................................49
5.2.6 Help Menu........................................................................................ 49
5.3 Toolbar ..........................................................................................................50
5.4 Re ult View ...................................................................................................51
5.5 Extended State .............................................................................................53
5.6 Configuration Window .................................................................................55
5.6.1 Sensor Tab .......................................................................................55
5.6.2 O T Tab............................................................................................. 56
5.6.3 nterface Tab.....................................................................................57
5.6.4 Camera Tab...................................................................................... 58
5.6.5 Control Tab .......................................................................................60
5.7 Device Data...................................................................................................60
5.8 Device Output...............................................................................................61
6 Operation and Communication ..............................................................................62
6.1 Communication via PROFINET...................................................................62
6.1.1 General nformation on Communication via PROF NET................... 62
6.1.2 PROF NET Modules......................................................................... 63
7 Communicating with the OIT Sy tem ....................................................................64
7.1 TCP/IP Communication with VSX Protocol................................................64
7.2 EtherNet TCP/IP Communication with Ea y Mode ...................................72
8 Trouble hooting.......................................................................................................76

O T500-F113-B17-CB
ntroduction
2019-12
5
1 Introduction
1.1 Content of thi Document
This document contains information required to use the product in the relevant phases of the
product life cycle. This may include information on the following:
•Product identification
•Delivery, transport, and storage
•Mounting and installation
•Commissioning and operation
•Maintenance and repair
•Troubleshooting
•Dismounting
•Disposal
The documentation comprises the following parts:
•This document
•Datasheet
n addition, the documentation may comprise the following parts, if applicable:
•EU-type examination certificate
•EU declaration of conformity
•Attestation of conformity
•Certificates
•Control drawings
•nstruction manual
•Other documents
1.2 Target Group, Per onnel
Responsibility for planning, assembly, commissioning, operation, maintenance, and dismount-
ing lies with the plant operator.
Only appropriately trained and qualified personnel may carry out mounting, installation, com-
missioning, operation, maintenance, and dismounting of the product. The personnel must have
read and understood the instruction manual and the further documentation.
Prior to using the product make yourself familiar with it. Read the document carefully.
Note
For full information on the product, refer to the further documentation on the nternet at
www.pepperl-fuchs.com.

2019-12
6
O T500-F113-B17-CB
ntroduction
1.3 Symbol U ed
This document contains symbols for the identification of warning messages and of informative
messages.
Warning Me age
You will find warning messages, whenever dangers may arise from your actions. t is mandatory
that you observe these warning messages for your personal safety and in order to avoid prop-
erty damage.
Depending on the risk level, the warning messages are displayed in descending order as fol-
lows:
Informative Symbol
Action
This symbol indicates a paragraph with instructions. You are prompted to perform an action or
a sequence of actions.
1.4 Regi tered Trademark
Micro oft
®
, Windows
®
, Windows 7
®
are registered trademarks of Microsoft Corporation. All fea-
tured trademarks and company names are subject to the copyright of the respective companies.
PROFINET®, PROFIBUS®: Trademarks of PROF BUS Nutzerorganisation e.V. (PNO)
SIMATIC, TIA Portal: Trademarks of S EMENS AG
Danger!
This symbol indicates an imminent danger.
Non-observance will result in personal injury or death.
Warning!
This symbol indicates a possible fault or danger.
Non-observance may cause personal injury or serious property damage.
Caution!
This symbol indicates a possible fault.
Non-observance could interrupt the device and any connected systems and plants, or result in
their complete failure.
Note
This symbol brings important information to your attention.

O T500-F113-B17-CB
Product Description
2019-12
7
2 Product De cription
2.1 Functional De cription
O T500-F113-B17-CB (referred to as the O T system from now on) uses infrared lighting and
evaluates special code sheets that feature hole patterns. For this purpose, the O T system is fit-
ted with a normal lens and an internal LED board for illuminating the code sheets. The infrared
lighting guarantees optimal contrasts during a read operation, so that even soiled code sheets
can be reliably identified. f the read result deteriorates during operation, the diagnostics will
automatically provide an analysis. You can use CB1 code sheets and CB3 code sheets for the
O T system. Further technical details can be found in the datasheet for the O T system.
Figure 2.1 Code sheet and identification system
2.2 Application and Area of U e
The O T system is used for automated manufacturing processes in harsh ambient conditions
where the use of read-only tags with electronic components is difficult or even impossible.
Code sheets with a perforated matrix are used as read-only tags. These code sheets are
designed for use at temperatures of up to 500 °C and can withstand high mechanical stress.
The device is easy to mount and is then ready for use immediately with no teach-in required.
Plug-in connections enable quick replacement of devices. The system is controlled via the
Ethernet interface using simple sets of commands, making it easy to operate. The scratch-
resistant quartz glass panel can be replaced if necessary.
The hole pattern punched into the code sheets features an D that is detected and processed
by the O T system. The read result is forwarded to the controller via PROF NET or to a com-
puter using the network interface. The D can contain information such as a type designation,
paint color, or similar information for the object on which the code sheet is mounted. To detect
the code sheets, the O T system is mounted directly in the plant.
The device is only approved for appropriate and intended use. gnoring these instructions will
void any warranty and absolve the manufacturer from any liability.
Use the device only within the specified ambient and operating conditions.
Protection of the personnel and the plant is not ensured if the device is not used according to its
intended use.

2019-12
8
O T500-F113-B17-CB
Product Description
2.3 LED Indicator
The LED indicator shows all important system and status information.
The nine LEDs mounted on the side of the device can be used to read different information.
Figure 2.2 LED ndicator
The seven LEDs mounted on the lighting unit can be used to read different information.
Po ition De cription Function
1GOOD
BAD
Reading successful (green) or failed (red)
2RDY
ERR
The LED flashes while initializing. During this time, no network
connection to the O T can be established. The LED lights up as
soon as the O T is ready for operation
3TRIGGER 1
TRIGGER 2
Lights up yellow when a connected trigger sensor is activated
4LINK 1 Lights up green when an Ethernet cable is connected
5ACT 1 Flashes orange: Data transfer on the PROF NET channel active
6BUS ERR Flashes red if there is no PROF NET connection available
7LINK 2 Lights up green when an Ethernet cable is connected
8ACT 2 Flashes orange: Data transfer on the PROF NET channel active
2
1
3
4
5
7
8
6

O T500-F113-B17-CB
Product Description
2019-12
9
Figure 2.3 Lighting unit of the O T system
Po ition De cription Function
1Code OK Reading successful
2Error Lights up red when a read error occurs
3Trigger Lights up yellow when a connected trigger sensor
is activated
4Stability of
image information
Lights up red if the captured image could be read but
increasing deterioration of the ambient conditions may
result in a reading error. This can occur, for example, in the
following situations: if the camera image is too light/dark, if
the contrast is too low, if there are too many structures in
the image, if the code sheet is just within the read dis-
tance, or if the code sheet is only just within the image
area.
5Ready for operation The LED lights up as soon as the O T is ready for
operation
6Power Lights up green when the O T system is supplied with
power
7Lighting control Lights up red when infrared illumination is active
1
2
3
4
5
6
7

2019-12
10
O T500-F113-B17-CB
Product Description
2.4 Interface and Connection
Figure 2.4 Connections
1. PROF NET/EtherNet TCP/ P connection 1
2. PROF NET/EtherNet TCP/ P connection 2
3. Trigger connection 1
4. Trigger connection 2
5. Power supply
6. Connection for external lighting
Pinout for PROFINET Connection 1 and 2
Figure 2.5 Pinout for PROF NET connection
1. Tx +
2. Rx +
3. Tx -
4. Rx -
1 3 5
642
1
3
42

O T500-F113-B17-CB
Product Description
2019-12
11
Pinout for Trigger Connection 1 and 2
Figure 2.6 Pinout for Trigger Connection
1. 24 V power supply
2. Not assigned
3. Ground
4. Trigger signal
5. Not assigned
Pinout for Power Supply
Figure 2.7 Pinout for power supply
1. /O 1
2. 24 V power supply
3. Not assigned
4. Not assigned
5. /O 2
6. /O 3
7. Ground
8. /O 4
15
3
2
4
7
4
1
5
3
6
2
8

2019-12
12
O T500-F113-B17-CB
Product Description
Pinout for External Lighting
Figure 2.8 Pinout for external lighting
1. 24 V power supply
2. Not assigned
3. Ground
4. Lighting control
5. Not assigned
2.5 Scope of Delivery
Check the packaging and contents for damage.
Check if you have received every item and if the items received are the ones you ordered.
ncluded in delivery:
•O T500-F113-B17-CB
•Mounting base (preassembled on the housing)
Always store and transport the device in the original packaging.
Store the device in a clean and dry environment. The permitted ambient conditions must be
considered, see datasheet.
15
3
2
4

O T500-F113-B17-CB
Product Description
2019-12
13
2.6 Acce orie
Various accessories are available.
2.6.1 Power Supply
2.6.2 Connection Cable for Trigger Sen or and External Lighting
Use the following connection cable to connect a trigger sensor or external lighting.
M12 cord et
Field-attachable M12 connector
Other lengths on request.
De cription De cription
V19-G-2M-PUR-ABG Single-ended female cordset, M12, 8-pin, shielded, PUR cable
V19-G-ABG-PG9 M12 single-ended female cordset, 8-pin, shielded, field-attach-
able
Material Length
M12 plug, traight M12 plug, angled
4-pin M12 socket,
straight
PUR
2 m V1-G-2M-PUR-V1-G V1-G-2M-PUR-V1-W
5 m V1-G-5M-PUR-V1-G V1-G-5M-PUR-V1-W
10 m V1-G-10M-PUR-V1-G V1-G-10M-PUR-V1-W
4-pin M12 socket,
straight
PVC
2 m V1-G-2M-PVC-V1-G V1-G-2M-PVC-V1-W
5 m V1-G-5M-PVC-V1-G V1-G-5M-PVC-V1-W
10 m V1-G-10M-PVC-V1-G V1-G-10M-PVC-V1-W
4-pin M12 socket,
angled
PUR
2 m V1-W-2M-PUR-V1-G On request
5 m V1-W-5M-PUR-V1-G On request
10 m V1-W-10M-PUR-V1-G On request
Model number De cription Cable dia.
V1S-G-BK 4-pin M12 plug, straight 4 ... 6 mm
V1S-G-ABG-PG9 4-pin M12 plug, straight 5 ... 8 mm
V1S-G PG9 4-pin M12 plug, straight 6 ... 8 mm
V1S-G-Q2 4-pin M12 plug, straight 4 ... 8 mm
V1S-G-Q3 4-pin M12 plug, straight 3.5 ... 6 mm

2019-12
14
O T500-F113-B17-CB
Product Description
2.6.3 Network Cable
The O T is connected to the network via a network connector.
Note
Network Connection with Degree of Protection IP65
The network connection on the O T has degree of protection P65.
De cription De cription
V1SD-G-2M-PUR-ABG-V45-G 2 m cordset, M12 to RJ45 PUR cable, 4-pin, CAT5e
V1SD-G-5M-PUR-ABG-V45-G 5 m cordset, M12 to RJ45 PUR cable, 4-pin, CAT5e
V1SD-G-10M-PUR-ABG-V45-G 10 m cordset, M12 to RJ45 PUR cable, 4-pin, CAT5e
V1SD-G-2M-PUR-ABG-V1SD-G 2 m cordset, M12 to M12, PUR cable, 4-pin, CAT5e
V1SD-G-5M-PUR-ABG-V1SD-G 5 m cordset, M12 to M12, PUR cable, 4-pin, CAT5e
V1SD-G-10M-PUR-ABG-V1SD-G 10 m cordset, M12 to M12, PUR cable, 4-pin, CAT5e

O T500-F113-B17-CB
Product Description
2019-12
15
2.6.4 Code Sheet
The code sheet serves as a read/write tag with a punched hole pattern for use at high tempera-
tures. The robust code sheet is suitable for use in environments up to 500 °C and remains legi-
ble even in the case of heavy contamination. You can use CB1 code sheets and CB3 code
sheets for the O T system.
Figure 2.9 CB1 code sheet
Figure 2.10 CB3 code sheet
Note
Ordering Code Sheet
The CB1 code sheet can be ordered from Pepperl+Fuchs.
The CB3 code sheets are still on the market, but cannot be ordered from Pepperl+Fuchs.

2019-12
16
O T500-F113-B17-CB
Product Description
Note
Contamination of the Code Sheet
Protect the code sheet from excess dirt. The code sheet can be cleaned using aggressive or
abrasive cleaning agents.
Ensure that no other markings are made on the code sheet, as this can affect the reading.

O T500-F113-B17-CB
Mounting and nstallation
2019-12
17
3 Mounting and In tallation
3.1 OIT Sy tem Overview
Figure 3.1 O T system, structural principle
The installation of the O T system involves just a few steps. n addition to the EtherNet TCP/ P
interface, the device has a trigger input for an optional trigger sensor (NBB20-L2-A2-V1 induc-
tive sensor shown for illustrative purposes).
The initial commissioning sequence is described in the following diagram. Each box indicates
one of the following subsections:
Figure 3.2 Schedule for initial commissioning
PLC
Mounting
the OIT system
Specifying the operating
distance
If nec. setting the
lighting angle
Mounting and aligning
the device
Mounting the code
sheet
Establishing
an electrical
connection
Connecting the power
supply
Connecting the network
cable
Optional: Connecting
a trigger sensor
Setting up
Windows
network
communication
Connecting
the OIT system
to the software
Displaying the
IP address of the device
Setting the IP address
of the PC
Note
Before carrying out the initial commissioning of an O T system, you must install the latest
version of the Vi ion Configurator software on your PC/laptop. An up-to-date description of
the Vision Configurator software can be found on our website at http://www.pepperl-fuchs.com.

2019-12
18
O T500-F113-B17-CB
Mounting and nstallation
3.2 Mounting the OIT Sy tem
3.2.1 Operating Di tance
The operating distance is the distance from the glass pane of the O T system to the code sheet.
The O T system is set to a reading distance of 380 mm by default.
Figure 3.3 Operating distance (top view)
Warning!
Danger to life due to defective mounting
Errors during mounting can cause life-threatening injuries and significant property damage.
•Ensure the installation is performed only by sufficiently trained and qualified personnel.
Trained and qualified personnel have relevant experience in this area. They know and
understand the rules and standards for the components and systems.
•Prior to mounting, ensure that the plant is de-energized.
•The device is relatively heavy. Handle the device carefully.
Note
Avoid bright areas in the background when mounting the code plate. The code plate must be
brighter than the background. f this is not the case, reading may be impossible.
300 ... 450 mm
170 mm
470 ... 620 mm
60 mm

O T500-F113-B17-CB
Mounting and nstallation
2019-12
19
Permi ible Code Sheet Di placement for CB1 Code Sheet
Figure 3.4 X/Y direction for the displacement of OIC-xxxx-CB1 Code sheet.
Figure 3.5 Permissible displacement of read-only tag ± X and ± Y depending on reading distance Z
A reading window in the X and Y direction determines the permissible displacement of read-
only tags. The graphic shows that as the operating distance increases, the possible code sheet
displacement increases. The graphic is applicable provided that the code sheet is parallel with
the O T system and the center of the code sheet is shown on the optical axis of the lens.
Code sheet displacement in X- and Y-directionWorking distance in Z-direction
Z
X
Y
X
Y
0
10
20
30
40
50
60
70
80
Operating distance Z/mm
ΔX
ΔY
Read range
ΔX and ΔY/mm
300 350 400 450 500

2019-12
20
O T500-F113-B17-CB
Mounting and nstallation
Permi ible Reading Window Di placement for CB1 Code Sheet
Figure 3.6 X/Y direction for the displacement of OIC-xxxx-CB1 code sheets
Reading Window for OIC-xxxx-CB1 Code Sheet
Code sheet displacement in the X and Y direction
ΔX
ΔY
Reading window in the X and Y direction
X
Y
-200
-150
-100
-50
0
50
100
150
200
Y/mm
Operating distance Z/mm
-200
-150
-100
-50
0
50
100
150
200
X/mm
Operating distance Z/mm
Reading window in the X direction Reading window in the Y direction
Read range Read range
300 350 400 450 500
300 350 400 450 500
Note
CB3 code heet
There is the option to use the CB3 code sheet.