Pepperl+Fuchs HD2-DM-A User manual

PROCESS AUTOMATION
MANUAL
HD2-DM-A / DM-AM / KT-MB-DMA
ADVANCED DIAGNOSTIC SOLUTIONS

With regard to the supply of products, the current issue of the following document is applicable:
The General Terms of Delivery for Products and Services of the Electrical Industry, as published by
the Central Association of the "Elektrotechnik und Elektroindustrie (ZVEI) e.V",
including the supplementary clause "Extended reservation of title".
We at Pepperl+Fuchs recognise a duty to make a contribution to the future.
For this reason, this printed matter is produced on paper bleached without the use of chlorine.

HD2-DM-A/DM-AM
List of content
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet www.pepperl-fuchs.com
3
1 Explanation of Symbols ........................................................................ 6
1.1 Safety-relevant Symbols ........................................................... 6
1.2 Informative Symbols ................................................................. 6
2 Introduction .......................................................................................... 7
2.1 Intended Use ............................................................................ 9
2.2 Maintenance and Service ....................................................... 10
2.3 Fault Elimination ..................................................................... 10
2.4 Disposal .................................................................................. 10
3 Product Specifications HD2-DM-A ..................................................... 11
3.1 Functional Description ............................................................ 11
3.2 Marking ................................................................................... 11
3.3 Technical Data ........................................................................ 12
3.4 LED Indication ........................................................................ 12
3.5 HD2-DM-A Voltage Free Contact Activation ........................... 14
3.6 Order Information .................................................................... 15
3.7 Dimensional Drawings ............................................................ 16
4 Product Specifications DM-AM .......................................................... 17
4.1 Functional Description ............................................................ 17
4.2 Marking ................................................................................... 17
4.3 Technical Data ........................................................................ 18
4.4 Device Component Overview ................................................. 18
4.5 LED Indication and Basic Troubleshooting ............................. 19
4.6 Order Information .................................................................... 20
4.7 Dimensional Drawings ............................................................ 21
5 Application Engineering HD2-DM-A ................................................... 22
5.1 Schematic Diagnostic Structure HD2-DM-A ........................... 22
5.2 Typical Applications ................................................................ 24
5.2.1 Local Application Structure .......................................... 24
5.2.2 Remote Application Structure ...................................... 25
5.3 Hardware Installation and Commissioning ............................. 26
5.3.1 Device Address Assigning, Mounting and Dismounting 26
5.3.2 Buildup the Diagnostic Bus ......................................... 28
5.3.3 Com Port Converter Additional Information ................. 29
5.4 Software Installation and Commissioning ............................... 29
5.5 Initial Commissiong of the Diagnostic Project
with PACTwareTM ..................................................................... 31
5.5.1 Approved Tags and Tag Values .................................. 31
5.5.2 Commissioning of the Diagnostic Project manually .... 32
5.5.3 Commissioning the Diagnostic Project automatically .. 35
5.5.4 Set Snapshot Archive Location ................................... 38

HD2-DM-A/DM-AM
List of content
S
ubject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in German
y
P
epperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet www.pepperl-fuchs.co
m
4
5.5.5 Diagnostic Manager Connection ..................................40
5.6 Import prepared or saved Diagnostic Project
with PACTwareTM .....................................................................40
6 Application Engineering DM-AM .........................................................42
6.1 Schematic Diagnostic Structure DM-AM .................................42
6.2 Mounting and Dismounting ......................................................44
6.2.1 How to use the Test Plug .............................................45
6.3 DM-AM Connection Details .....................................................47
6.4 FDT/DTM Diagnostic Manager Installation
and Commissioning .................................................................48
6.4.1 Diagnostic Manager Connection ..................................50
7 FDS and OPC Server .........................................................................51
7.1 FDS-Control Center settings ...................................................51
7.2 FieldConnexRDiagnostic Server (FDS) ..................................51
7.2.1 FDS-Settings ................................................................52
7.3 OPC Server .............................................................................53
7.3.1 OPC-DA Server Name Space ......................................53
7.3.2 OPC-AE Message Data ...............................................56
7.4 FDS Network Information ........................................................57
8 Operation with the Diagnostic Manager ..............................................58
8.1 Commissioning Wizard ............................................................59
8.2 Diagnostics ..............................................................................61
8.2.1 System Diagnostics Window ........................................61
8.2.2 Diagnostic Module Diagnostics Window ......................62
8.2.3 Diagnostic Module Diagnostics Window Overview ......62
8.2.4 Alarm Icon Description .................................................63
8.2.5 Diagnostics Filter Function ...........................................63
8.3 Segment Monitoring ................................................................65
8.3.1 Segment Monitoring Data Table Overview ..................66
8.3.2 Physical Layer Measurement Reports (Snapshot) .......68
8.4 Snapshot Explorer ...................................................................69
8.5 Detail Parameterization Interfaces ..........................................70
8.5.1 Diagnostic Manager User Interface Description ...........72
8.5.2 Online/Offline Interface Menu Structure Overview .......73
8.5.3 HD2-DM-A Operation Modes .......................................74
8.5.4 Field Device Handling ..................................................76
8.5.5 PROFIBUS Field Device Measurement Handling .......78
8.5.6 Failure and Maintenance Alarm Handling ....................78
8.5.7 Alarm Hysteresis and Reset .........................................81
8.6 Long-Term History ...................................................................81
8.6.1 History Data Export ......................................................82
8.7 Fieldbus Oscilloscope Function ...............................................83

HD2-DM-A/DM-AM
List of content
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet www.pepperl-fuchs.com
5
8.7.1 Oscilloscope Screen Overview .................................... 83
8.7.2 Trigger Conditions ....................................................... 85
8.8 Firmware Update .................................................................... 87
9 Measured Values / Parameters .......................................................... 88
10 Use Cases and Troubleshooting ....................................................... 94
10.1 Use Cases .............................................................................. 94
10.1.1 Diagnostics During Installation .................................... 94
10.2 Troubleshooting ...................................................................... 96
10.2.1 Diagnostic Manager/Error Messages .......................... 96
11 Installation in Hazardous Areas ....................................................... 100
11.1 Safety Instructions ................................................................ 100
11.2 Installation of the HD2-DM-A in Conjunction with the
Power Hub within Zone 2 or Class I Div. 2
or Class I, Zone 2 ................................................................. 100
11.2.1 Degree of Protection ................................................. 101
11.3 Installation of the DM-AM within Zone 2,
Class I Division 2 Area or Class I, Zone 2 ............................ 101
12 List of Referenced Documents ......................................................... 102
12.1 Norms ................................................................................... 102
12.2 Guidelines ............................................................................. 102
13 Working with the Stand-alone Diagnostic Kit ................................... 101
13.1 Component Overview ........................................................... 102
13.2 Connections .......................................................................... 103
13.3 Commisioning with the Diagnostic Manager ......................... 104

HD2-DM-A/DM-AM
Explanation of Symbols
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
6
187630
1 Explanation of Symbols
1.1 Safety-relevant Symbols
1.2 Informative Symbols
•
This symbol indicates a warning about a possible danger.
In the event the warning is ignored, the consequences may range from
personal injury to death or from damage to equipment to destruction.
•
This symbol warns of a possible fault. Failure to observe the instructions
given in this warning may result in the device and any connected facilities
or systems to it develop a fault or fail completely.
This symbol brings important information to your attention.
#This symbol marks an acting paragraph.

HD2-DM-A/DM-AM
Introduction
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
7
187630
2 Introduction
This manual describes the following products:
• The Advanced Diagnostic Module HD2-DM-A, for mounting lo-
cally on a FieldConnexRPower Hub motherboard.
• And the Mobile Advanced Diagnostic Module DM-AM, the mo-
bile solution for selective analyzing, monitoring and troubles-
hooting in the field.
The Advanced Diagnostic Modules are specially designed to analyse
signal and segment parameters. They also let you monitor and measure
specific system, segment and field device values. The continuous live
monitoring of all relevant physical layer parameters enables the con-
stant validation of the signal quality and to proactively detect degradati-
ons before the segment communication fails.
The Diagnostic Modules are part of the diagnostic system, which con-
sists of different hard- and software components that act as a whole
(see chapter 5.1 and chapter 6.1).
In conjunction with the FDT/DTM based Diagnostic Manager both Dia-
gnostic Modules provide analysis of signal and segment parameters as
well as measurement of specific system and field device physical layer
values. The integrated powerful oscilloscope function visualizes the cur-
rent communication at each segment.

HD2-DM-A/DM-AM
Introduction
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
8
187630
Quick Device Comparison
For detailed information about the whole Pepperl+Fuchs Fieldbus In-
stallation Technology and Fieldbus Power Hub product range please re-
fer to the comprehensive system manuals and data sheets or contact
your local Pepperl+Fuchs representative.
This described products are developed and manufactured in com-
pliance with applicable European standards and guidelines.
Function HD2-DM-A DM-AM
Preferred type of
usage
Lifecycle support,
long term supervision
and proactive ser-
vices of complete
Fieldbus plants or
parts of it.
Commissioning, vali-
dation, troubleshoo-
ting, lifecycle support
and long term super-
vision for individual
segments.
Device supply via motherboard USB-powered
Number of monitored
segments
41
Connection to PC Com-Port Converter via USB
Physical-Layer-Dia-
gnosis
YES YES
Bulk-Power-Supply
monitoring
YES NO
Segment supply mo-
nitoring
YES YES
OPC integration YES NO
Powerful oscilloscope
function
YES YES
LED indication YES YES
A corresponding Declaration of Conformity may be requested from the
manufacturer.

HD2-DM-A/DM-AM
Introduction
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
9
187630
The described devices must only be operated by trained professionals
in accordance with this manual.
It is assumed that the user has technical knowledge of and experience
with FOUNDATION Fieldbus and/or PROFIBUS PA technology, explosi-
on protection, as well as planning and installing FOUNDATION Field-
bus/PROFIBUS PA systems. This document does not provide a comple-
te introduction to FOUNDATION Fieldbus, PROFIBUS PA or explosion
protection for inexperienced users.
The Statement of Conformity, Certificate of Compliance and data
sheets are considered as an integral part of this manual. The data
sheets contain the electrical data of the Statement of Conformity and
the Certificate of Compliance.
Laws and/or regulations governing the use or intended use must be ob-
served. The described devices are only approved for proper professio-
nal use in accordance with the intended purposes. Improper handling
will void any claim made under the warranty as well as any manufactu-
rer's liability.
All Pepperl+Fuchs specific documents are available at
www.pepperl-fuchs.com or from your local Pepperl+Fuchs representa-
tive.
2.1 Intended Use
The Advanced Fieldbus Diagnostic solutions are designed to analyse
signal and segment parameters for monitoring and measuring of
specific system, segment and field device values.
•
•
The manufacturer of the product, Pepperl+Fuchs GmbH in D-
68307 Mannheim, has a certified quality assurance program in
accordance with ISO 9001.
•
Protection of operating personnel and the system is not ensured if the
module is not used in accordance with its intended purpose.

HD2-DM-A/DM-AM
Introduction
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
10
187630
2.2 Maintenance and Service
The measurement properties of the described devices are stable over
long periods of time. For this reason, regular adjustment or service or
the like is unnecessary.
2.3 Fault Elimination
2.4 Disposal
Disposal of devices and their packaging material must be performed in
compliance with the applicable laws and guidelines of the correspon-
ding country.
The devices contain no batteries which must be disposed of separately
from the devices.
•
The operator of the system is responsible in terms of planning,
mounting, commissioning, operating and maintenance.
•
If devices are operated in general electrical systems they must not the-
reafter be operated in electrical systems that are connected with hazar-
dous areas.
•
The delivered transport case of the Mobile Advanced Diagnostic Module
and some of its content must not be taken into hazardous areas.
•
Devices being operated in connection with hazardous areas must not be
changed or manipulated.
•
In case of defect, the device must be removed and replaced with a new
one.

HD2-DM-A/DM-AM
Product Specifications HD2-DM-A
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
11
187630
3 Product Specifications HD2-DM-A
3.1 Functional Description
3.2 Marking
The HD2-DM-A is the motherboard mounted diagnostic so-
lution for four fieldbus segments.
The preferred type of usage is lifecycle support, long term
supervision and proactive services of complete Fieldbus
plants or parts of it with extended demands on reliability
and continuity.
A special developed FDT/DTM based Diagnostic Manager
enables fast and easy commissioning and validation of
Fieldbus installations as well as easy every day handling.
•
Advanced Diagnostic Module
Pepperl+Fuchs
D-68307 Mannheim
HD2-DM-A
TÜV 04 ATEX 2500 X
•
II 3 G EEx nA II T4

HD2-DM-A/DM-AM
Product Specifications HD2-DM-A
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
12
187630
3.3 Technical Data
3.4 LED Indication
Advanced Diagnostic Module HD2-DM-A
Supply
Rated voltage 19.2 to 35 V
Rated current 110 to 30 mA
Power loss max. 2 W
Fieldbus interface
Number of segments 4
Rated voltage 9 to 32 V
Ambient conditions
Ambient temperature -40 to 60 °C (-40 to 140° F)
Storage temperature -40 to 85 °C (-40 to 185° F)
Shock resistance 15 g 11 ms
Vibration resistance 1 g, 10 to 150 Hz
Humidity <95 % non-condensing
For complete technical data please refer to the corresponding data
sheets.
•1 LED status segment 1
2 LED status segment 2
3 LED status segment 3
4 LED status segment 4
5 LED Primary power connection
6 LED Secondary power connection
Seg4
Seg3
Seg2
Seg1
SEC
PWR
PRI
PWR
Fieldbus
Diagnostic
Module
Advanced
Version
HD2-
DM-A
1
2
3
4
5
6

HD2-DM-A/DM-AM
Product Specifications HD2-DM-A
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
13
187630
LED indication Fault type Remedy
PRI PWR and/or
SEC PWR LEDs
are off
Supply power failure:
possible reasons:
• no primary and/or
secondary sup-
ply power is avail-
able
• supply power is
less than 19.2 V
• supply power is
higher than 35 V
(32 V if at least
one non-isolated
power module is
plugged-in or
configured)
Connect diagnostic PC and carry out
a complete system diagnosis:
Bulk power supply switched on and
healthy?
Verify that the wiring is secure:
• Tug on the wires/cable-clamps
• Measure the DC voltage at the ter-
minal block connector to the bulk
power supply
One segment
LED is flashing
yellow (on/off
with 2 Hz)
A segment/field de-
vice maintenance re-
quired alarm is active.
All segment
LED are flashing
yellow (on/off
with 2 Hz)
A system mainte-
nance required alarm
is active.
One segment
LED is flashing
red (on/off with
2Hz)
Any segment/field de-
vice alarm is active.
Connect diagnostic PC and carry out
a complete system diagnosis:
• DC unbalance
• too high jitter level
• too high noise level
Bus segment...
• ...badly terminated?
• ...miswired (shield connections)?
• ...short circuit overload?
Power supply/conditioner modules
healthy and well mounted?
All segment
LEDs are flash-
ing red
(on/off with 2
Hz)
Any system alarm is
active
Connect diagnostic PC and carry out
a complete system diagnosis:
Bulk power supply voltage correct?
Board type configuration correct?
Board redundancy configuration cor-
rect?
Any (or all) seg-
ment LEDs
lights solid red
A hardware fault in-
side HD2-DM-A is de-
tected
Replace the device with a new one!

HD2-DM-A/DM-AM
Product Specifications HD2-DM-A
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
14
187630
3.5 HD2-DM-A Voltage Free Contact Activation
All Power Hub Motherboards (excepting MB-FB-1R) containing a com-
mon alarm voltage free contact. By affecting a relay general failure sta-
tus is given, for further information see chapter „Fieldbus Power Hub Ba-
sic Diagnostics“ at the Fieldbus Power Hub System Manual. As the
Basic Diagnostic Module the Advanced Diagnostic Module HD2-DM-A
sets the relay contact, too. While no alarm occurs the contact is closed.
It opens when a maintenance alarm limit value is violated.
The check outs with the corresponding relay status are given in the table
below.
Relay status
Check out Maintenance alarm Out-of-Specification
alarm
Bulk Power Sup-
ply Voltage
High / Low
• •
Segment
Voltage
High / Low
• •
Segment
Current
High / Low
•n.a.
Power Supply
Module mis-
match
n.a.•
Power Supply
Module failed n.a.•
Fieldbus Signal
level High / Low
• •
Unbalance • •
Noise • •
Jitter • •

HD2-DM-A/DM-AM
Product Specifications HD2-DM-A
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
15
187630
3.6 Order Information
Order name Description
HD2-DM-A Advanced Diagnostic Module allows, in conjunction with
the FDT/DTM based Diagnostic Manager, analysis of
signal and segment parameters as well as measurement
of specific system and field device physical layer values.
Basic DTM Free of charge Basic Diagnostic Manager with limited
functionality. Available at
www.pepperl-fuchs.com.
DTM-FC.AD Professional Diagnostic Manager, for up to or including
100 segments per production plant. Offers the full func-
tionality including trending, report generation, oscillo-
scope function and an easy to operate Wizard for
diagnostic commissioning.
DTM-FC.AD.1 Professional Diagnostic Manager, for more than 100
segments per production plant. Offers the full functional-
ity including trending, report generation, oscilloscope
function and an easy to operate Wizard for diagnostic
commissioning.

HD2-DM-A/DM-AM
Product Specifications HD2-DM-A
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
16
187630
3.7 Dimensional Drawings
•
Figure 3.1: HD2-DM-A
The HD2-DM-A Module can be mounted on different Fieldbus Power
Hub motherboards. For dimensions of the mounted systems, please re-
fer to the corresponding motherboard data sheet.
All dimensions in millimeters and inches (values in brackets) and without
tolerance indication.
HD2-
DM-A

HD2-DM-A/DM-AM
Product Specifications DM-AM
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
17
187630
4 Product Specifications DM-AM
4.1 Functional Description
4.2 Marking
The Mobile Advanced Diagnostic
Module DM-AM is a USB-powered
tool to analyze the physical layer pa-
rameters of one fieldbus segment at a
time.
The preferred type of usage is com-
missioning and validation of new or
reworked Fieldbus segments as well
as the fast troubleshooting of a re-
spective segment in the case of a
failure.
•
Specially developed FDT/DTM based Diagnostic Manager enables
fast and easy commissioning and validation of Fieldbus installations as
well as reliable troubleshooting on the spot.
Mobile Advanced Diagnostic Module
Pepperl+Fuchs
D-68307 Mannheim
DM-AM
TÜV 05 ATEX 2923 X
•
II 3 G EEx nA [nL] IIC T4

HD2-DM-A/DM-AM
Product Specifications DM-AM
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
18
187630
4.3 Technical Data
4.4 Device Component Overview
Mobile Advanced Diagnostic Module DM-AM
Supply
Rated voltage 20 to 30 V
Rated current 70 to 30 mA
Power loss 0.7 W
Fieldbus interface
Number of segments 1
Rated voltage 9 to 32 V
Ambient conditions
Ambient temperature -40 to 60 °C (-40 to 140° F)
Storage temperature -40 to 85 °C (-40 to 185° F)
Shock resistance 15 g 11 ms
Vibration resistance 1 g, 10 to 150 Hz
Humidity <95 % non-condensing
For complete technical data please refer to the corresponding data
sheets.
•1 LED Segment Communication/
Error
2 LED Power supply indication
3 USB interface
4 Power supply connections
5 Fieldbus connection

HD2-DM-A/DM-AM
Product Specifications DM-AM
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
19
187630
4.5 LED Indication and Basic Troubleshooting
LED indication Fault type Fault clearance
LED PWR is off Supply power failure:
no supply power is
available
or
supply power is less
than 20 V
or
supply power is high-
er than 30 V
USB-supply less than
150 mA?
• Use an externally-
supplied USB-Hub
Verify that the wiring is
secure:
• Tug on the wires/ca-
ble-clamps
• Measure the DC
voltage at the termi-
nal block connector
of the bulk power
supply or use the de-
livered AC/DC
adapter
LED COM/ERR is
flashing yellow
(on/off with 2 Hz)
A segment/field de-
vice maintenance re-
quired alarm is active.
LED COM/ERR is
flashing red (on/
off with 2 Hz)
A segment/field de-
vice alarm is active.
Connect diagnostic
PC and carry out a
complete system diag-
nosis:
• DC unbalance
• jitter level too high
• noise level too high
Bus segment...
• ...badly terminated?
• ...miswired (shield
connections)?
• ...short circuit over-
load?
LED COMM/ERR
lights solid red
A hardware fault in-
side the DM-AM is
detected
Replace the device with
a new one!

HD2-DM-A/DM-AM
Product Specifications DM-AM
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
20
187630
4.6 Order Information
Order name Description
DM-AM-KIT The Mobile Advanced Diagnostic Kit scope of delivery:
• Transport case
• Mobile Advanced Diagnostic Module DM-AM
• USB 2.0 cable
• Fieldbus cable with test clamps and DM-AM Field-
bus connector
• Mounting clip
• Software package
DM-AM-WPS AC/DC adapter / Wall Power Supply
Basic DTM Free of charge Basic Diagnostic Manager, comes with
the Diagnostic Module. This Toolsuite reads generic
physical layer information of the fieldbus segments.
DTM-FC.ADM Professional Diagnostic Manager, offers the full func-
tionality including alarming, trending, report generation
and the oscilloscope function.