Pepperl+Fuchs KT-LED-24-PT100-24VDC User manual

KT-LED-24-PT100-24VDC
Operation Manual
Your automation, our passion

KT-LED-24-PT100-24VDC KT-LED-24-PT100-24VDC
10
Summary
1 Short description ...................................................................................................11
2 Safety instructions and warnings ..........................................................................11
2.1 Use according to the intended purpose ........................................................11
3 Mounting ...............................................................................................................12
3.1 Installation......................................................................................................12
3.2 Electrical connection......................................................................................12
4 Start-up .................................................................................................................12
5 Programming.........................................................................................................12
5.1 Switching to programming .............................................................................12
5.2 Changing the parameter setting.....................................................................13
5.3 Saving the parameter setting.........................................................................13
5.4 Programming ............................................................................................... 13
5.5 End of programming ......................................................................................15
6 Operation ..............................................................................................................15
6.1 Switching the display during operation ..........................................................15
6.2 Saving the momentary value .........................................................................16
7 Error and alarm messages....................................................................................16
8 General technical features ....................................................................................16
8.1 Electrical features ..........................................................................................16
8.2 Mechanical features.......................................................................................16
8.3 Environmental conditions...............................................................................17
9 Scope of delivery................................................................................................... 17
10 Order code ............................................................................................................17
11 Dimensions ...........................................................................................................17
Note :
The fields with a grey background contain the
factory-set default values.

KT-LED-24-PT100-24VDC KT-LED-24-PT100-24VDC
english
11
1 Short description
This digital display is an easy-to-use, microprocessor-con-
trolled device for the display (and the acquisition) of mea-
sured temperature values. The temperatures are measured
by means of Pt100 or Ni100 resistance thermometers. They
can display either the current measured value, the maxi-
mum value or the minimum value. In case of power switch-
off, the maximum and minimum values are stored in an
EEPROM. The values are restored as soon as the display
is powered again. The Latch input is isolated electrically
from the signal input by means of an optocoupler. It allows
storing the current measured value.
The supply voltage (10 .. 30 V DC) is isolated electrically
from the signal input by means of a DC/DC converter.
2 Safety instructions and warnings
Only use this display
– in a way according to its intended purpose
– if its technical condition is perfect
– adhering to the operating instructions and
the general safety instructions.
1. Before carrying out any installation or maintenance
work, make sure that the power supply of the digital
display is switched off.
2. Only use this digital display in a way according to its in-
tended purpose.
3. If its technical condition is perfect.
4. Adhering to the operating instructions and the general
safety instructions.
5. Adhere to country or user specific regulations.
6. The digital display is not intended for use in areas with
risks of explosion and in the branches excluded by the
standard EN 61010 Part 1.
7. The digital display shall only operate if it has been cor-
rectly mounted in a panel, in accordance with the chap-
ter “Main technical features”.
2.1 Use according to the intended purpose
The digital display only may be used as a panel-mounted
device. Applications of this product may be found in indust-
rial processes and controls, in the branch of the manufactu-
ring lines for the metal, wood, plastics, paper, glass, textile,
etc., processing industries.
Overvoltages at the terminals of the digital display must be
limited to the values of overvoltage category II.
If the digital display is used to monitor machines or proces-
ses in which, in case of a failure of the device or an error
made by the operator, there might be risks of damaging the
machine or causing accidents to the operators, it is up to
you to take appropriate safety measures.
!

KT-LED-24-PT100-24VDC KT-LED-24-PT100-24VDC
12
3 Mounting
3.1 Installation
1. The digital display shall not be installed near to contactors
or motor starters.
2. We recommend the use of wire end ferrules in order to
avoid short-circuits between adjacent terminals.
3. In order to keep the interferences at the measuring input
as low as possible, the signal and power supply wires
must be routed separately.
4. Use shieded cables for all signal/probe wirings and
2. The display shows the following message.
1234567
ϑ
5. Programming
5.1 Switching to programming
To switch to the programming mode:
1. switch the power supply of the device off, press simulta-
neously both keys on the front side, and then switch the
power supply on again.
⇑⇑
3-wire resistance thermometer
1234567
ϑ
3. release both keys. The first parameter to be set
appears on the display. The display switches every
second between the following messages
1 s
4. press the left key to stop the display from
switching. The last programmed parameter setting
is displayed.
3.2 Electrical connection
3.2.1 Pt100/Ni100 resistance thermometers
2-wire resistance thermometer
4-wire resistance thermometer
1234567
ϑ
3.2.2 Supply voltage and Latch input connection
1234567
1
2
3
1 10 ... 30 V DC
2 0 V DC (GND)
3 Latch input
avoid routing the signal/probe wirings parallel to each
other. The shield shall only be grounded at one point in
order to avoid ground loops.
Important note:
Before carrying out any installation or maintenance work,
make sure that the power supply of the digital display is
switched off.
4. Start-up
After switching on the supply voltage:
1. a display test is carried out
(Duration: 2 seconds)
2. Device type and software
version are displayed
(Duration: 2 seconds))
3. the selected probe is displayed
(Duration: 2 seconds).
4. the display is ready to operate and
the measured value is displayed.

KT-LED-24-PT100-24VDC KT-LED-24-PT100-24VDC
english
13
5.2 Changing the parameter setting
1. press the right-hand/grey key to change the
parameter setting by one value at a time
2. to input numerical values, select first the decade with the
left-hand/red key
3. the decade blinks
5.3 Saving the parameter setting and
switching to the following parameter
1. keep the left/red key pressed
5.4 Programmng the adjustable parameters
5.4.1 Input signal type
Range
Selection in the menu
Pt100 probe
Ni100 probe
⇑
⇑
⇑
4. set now the numerical value using the right-hand/
grey key
5. to reach the following decade, press the left-
hand/red key
6. if negative numerical values are required, set the left
decade to “–” or “–1”.
2. and press simultaneously the right/grey key.
⇑
⇑
⇑
Note:
The fields with a grey background
contain the factory-set default va-
lues.

KT-LED-24-PT100-24VDC KT-LED-24-PT100-24VDC
14
5.4.3 Decimal point
Decimal point
Selection in the menu
Resolution 0,1 °C/0,1 °F
Resolution 1 °C/1 °F
5.4.5 Correction value
Inputting a correction value allows acting upon the display-
ed result. These correction values may be
Setting the correction value
Selection in the menu
5.4.6 Maximum value acquisition
The maximum value may be saved and consulted during
operation (see 6.1)
Selection in the menu
Maximum value acquisition on
Maximum value acquisition off
5.4.4 Temperature unit
Unit
Selection in the menu
Display in °C
Display in °F
positive or negative. The input is always made with one
decimal place.
5.4.6.1 Resetting the maximum value
This allows defining whether the maximum value can be
reset during operation or not. However, the maximum value
can only be reset if the maximum value display is the active
function (see 6.1). If the maximum value is reset, the cur-
rent measured value becomes the new maximum value.
Selection in the menu
The maximum value can be reset
using the red key
The maximum value cannot be reset
......
Correction value in 0,1 °C/0,1 °F,
depending on the unit selected
5.4.2 Measuring method
Measuring method
2 wires; please note
See point 5.4.2.1 op-
posite!
3 wires
4 wires
Selection in the menu
...
Input here the line resistivity of your 2-wire probe for
long connection cables. If the resistivity value input
here is wrong, the displayed result will not be correct.
line resistivity
5.4.2.1 Line resistivity
If you selected the 2-wire measuring method in 5.4.2, the
display shows

KT-LED-24-PT100-24VDC KT-LED-24-PT100-24VDC
english
15
5.4.7 Minimum value acquisition
The minimum value may be saved and consulted during
operation (see 6.1)
Selection in the menu
Minimum value acquisition on
Minimum value acquisition off
5.5 End of programming
When programming is finished, end the prorgamming
routine as follows:
Selection in the menu
Programming restarts. The set values
can be checked and modified.
Programming is finished. The set
values are used in operation.
5.4.7.1 Resetting the minimum value
This allows defining whether the minimum value can be
reset during operation or not. However, the minimum value
can only be reset if the minimum value display is the active
function (see 6.1). If the minimum value is reset, the current
measured value becomes the new minimum value.
Selection in the menu
The minimum value can be reset using
the red key
The minimum value cannot be reset
6. Operation
6.1 Switching the display during operation
press the right-hand/grey key to select among the following
functions:
–current measured value
–minimum value
–maximum value.
Press the key once to display the designation of the active
display function for 2 seconds. If, during this time, the right-
hand grey key is pressed a second time, the display swit-
ches to the following display function. This is confirmed by
a 2-second display of the designation of the new function.
After these 2 seconds, the display shows, depending on the
selection, the maximum value, the minimum value or the
current measured value.
1. Current measured value, press once the right-hand/
grey key
2. Minimum value (when active), press once the
right-hand/grey key
3. Maximum value (when active), press once the
right-hand/grey key
4. Current measured value, press once the
right-hand/grey key
⇑
for 2 s:
after 2 s:
⇑
for 2 s:
after 2 s:
⇑
for 2 s:
after 2 s:
⇑
for 2 s:
after 2 s:

KT-LED-24-PT100-24VDC KT-LED-24-PT100-24VDC
16
6.2 Saving the momentary value (Display-Latch)
In case of a High Signal at the Latch input, the current mea-
sured value is frozen on the display. The minimum and ma-
ximum value acquisition continues operating in the back-
ground.
7 Troubleshooting and alarm messages
7.1 Display does not light up
If the display does not light up, check the supply voltage
or the power supply cables. Do not open the housing by
force.
7.2 Measuring rang overow or underow
Measuring range overow
Ranges see 8.1
Measuring range underow
Ranges see 8.1
7.3 Input problems
Probe broken or input
signal exceeds the
allowable range
8 Main technical features
Operation: by means of two front panel keys
DIsplay: 5-digit display, red 7-segment LED’s,
Height of the figures 8 mm
Display range: (see temperature range), with leading ze-
ros suppression Measuring range overflow,
indicated by ooooo on the display.
Measuring range underflow, indicated by
uuuuu on the display.
8.1 Electrical features
Input: PT100 resistance thermometer
Ni100 resistance thermometer
Supply current:
1 mA
Circuit type: 2-wire, 3-wire and 4-wire connection tech-
nique, programmable
with probe breakage monitoring
Temperature ranges:
Pt100 acc. to DIN IEC 751:
-199.9°C .. +850.0°C (-327.8°F .. 1562.0°F)
Ni100 acc. to DIN 43760:
-60.0°C .. +250.0°C (-76.0°F .. 482.0°F)
Resolution: 0,1°C (0,1°F) or 1°C (1°F), programmable
Linearity error PT100:
< 0,1 % for the whole measuring range at
an ambient temperature of 20°C
Linearity error Ni100:
< 0,2 % for the whole measuring range at
an ambient temperature of 20°C
Temperature drift:
0,1 K/Kambient
Measuring rate:
5 measurements/second, fixed
Display refresh:
1 ... 2 times per second
Display Latch input:
DIsplay stop for the current measured
value, active for log. 1
Switching log. 0: 0 ... 2 VDC
level log. 1: 4 ... 30 VDC
Supply voltage:
10 ... 30 V DC, electrically separated,
with Verpolschutz
Current consumption:
max. 40 mA
Test voltage: 500 Veff; 50/60 Hz; 1 min
Data backup: EEPROM
8.2 Mechanical features
Housing: Housing for control panel 48 x 24 mm
according to DIN 43 700, RAL 7021
Dimensions: (W x H x D):
48 x 24 x 66 mm
Panel cut-out: (W x H):
45+0,6 x 22,2+0,3 mm
Mounting depth:
approximately 59 mm
Weight: approximately 50 g
Protection level:
IP65 (on the front side)
Connection: Screw terminal, RM 5.08, 7 poles
Connection diameter:
single-wire 0,14 .. 1,5 mm2
thin wire 0,14 .. 1,5 mm2
wire dimensionsAWG 26-16

KT-LED-24-PT100-24VDC KT-LED-24-PT100-24VDC
Connections
1. 10 ... 30 V DC Supply voltage
2. 0 V DC GND
3. Latch - Input
4. Pt100/Ni100
5. Pt100/Ni100 (Sensor-input
6. Pt100/Ni100 see page 14)
7. Pt100/Ni100
english
17
8.3 Environmental conditions
EMC:
Interference immunity:
with shielded signal and control lines
not intended for local DC electricity
supply network(s) /battery connecting
cable ≥ 30 m
Device Safety
Protection Class:
Protection Class 2 (front side)
Application area:
Pollution level 2 over-voltage Category II
Insulation: Front: double insulation,
Rear side: basic insulation
Signal inputs and und sensor power supply: SELV
Operating temperature:
-20 °C ... +65 °C, relative humidity < 85%
Storage temperature:
-25 °C ... +70 °C
11 Digital display dimensions
Panel cut-out
Countersinking Af3, DIN 74
1
Panel cut-out
Only the front side is classified as
accessible for the operator
9 Scope of delivery
Digital display
Clamp
Front panel for clamp mounting,
Panel cut-out 50 x 25 mm
Front panel for screw mounting,
Panel cut-out 50 x 25 mm
Seal
Multilingual operating instructions
1 set of self-adhesive symbols
10 Order code
KT-LED-24-PT100-24VDC
Mounting frame

Weltweit
Pepperl+Fuchs SE
Lilienthalstraße 200
68307 Mannheim
Deutschland
Telefon: [phone]
E-Mail: [email protected]
https://www.pepperl-fuchs.com
Änderungen vorbehalten · © Pepperl+Fuchs
Printed in Germany
DOCT-1811B
R60133.9393 - Index 3 · 10/2023
Pepperl+Fuchs Quality
Download our latest policy here:
www.pepperl-fuchs.com/quality