Pepperl+Fuchs PMI360D-F130-IE8-V15-Y205400 User manual

1Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
Zero position
Direction of rotation
Push buttons
LEDs
10.3 ± 0.3
110
76.5
180°
270°
+
90°
360°/0°
30
ø 41.5
26
40
ø 10 ø 5.2
• Measuring range 0 ... 360°
• Analogue output 4 mA ... 20 mA
• Option of parameterizing signaling
zone, position and width
General specifications
Installation not embeddable
Measuring range 360°
Rotational speed ≤100 min-1
Nominal ratings
Operating voltage UB18... 30 V
Reverse polarity protection protected against reverse polarity
Repeat accuracy 0.5°
Resolution 0.4°
Temperature drift 1.5° (-25 °C ... 70 °C)
No-load supply current I0≤45 mA
Operating voltage display LED green
Switching output
Output type 2 switch outputs pnp, NO , protected against reverse polarity , short-circuit proof
Operating current IL≤100 mA
Voltage drop ≤3 V
Short-circuit protection pulsing
Analogue output
Output type 1 current output: 4 ... 20 mA
Linearity error ≤1.2 °
Load resistor ≤400 Ω
Ambient conditions
Ambient temperature -25 ... 70 °C (248... 343 K)
Mechanical specifications
Connection type connector M12 x 1, 5-pin
Housing material PBT
Shaft diameter ≤27.5 mm Steel
Protection degree IP67
Mass 180 g
L+
I
1/BN
4/BK
2/WH
5/GY
4-20mA
3/BU L-
Ind. angular measuring system
PMI360D-F130-IE8-V15-
Y205400
Features Technical Data
Electrical Connection
Order Code
Dimensions
Release date: 2010-01-12 11:45 Issue date: 2010-01-12 205400_ENG.xml
PMI360D-F130-IE8-V15-Y205400

2
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group • Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://www.pepperl-fuchs.com
Description of Sensor Functions
This Sensor provides functions, which are different from the series standards!
Note:
The basic parts of the standard devices instruction manual is also valid for this sensor. It is supplemented or partly
replaced by the description below.
The Sensor provides 2 switch outputs. For each output the width and the position of a
switching window can be programmed.
Each output can be programmed fully independent from the other. In case of a programmed switching window,
which exceeds 360° (multi-turn), only the angular range of the last incomplete revolution will be saved as the re-
sulting switching window.
Programming the Switching Window
Note:
A constantly lit green LED indicates the sensor’s operational status.
Programming the Switching Window S1
1. Press the programming button S1 for 2 s (yellow LED S1 flashes)
2. Place the target at the desired start point of the switching window
3. Press the programming button S1 briefly (yellow LED S1 goes on briefly and then flashes again)
4. Place the target at the desired end point of the switching window
5. Press the programming button S1 briefly (yellow LED S1 goes on as confirmation). The sensor returns to
normal operation.
Programming the Switching Window S2
1. Press the programming button S2 for 2 s (yellow LED S2 flashes)
2. Place the target at the desired start point of the switching window
3. Press the programming button S2 briefly (yellow LED S2 goes on briefly and then flashes again)
4. Place the target at the desired end point of the switching window
5. Press the programming button S2 briefly (yellow LED S2 goes on as confirmation). The sensor returns to
normal operation.
Characteristic Curves/Additional
Information
Accessories
BT-F130-A
Activator
V15-G-2M-PVC
Cable connector
V15-W-2M-PVC
Cable connector
a
b
d
a = 8
b ≥ 23
t ≥ 2
d = 1 - 2
t
ø 41.5
dimensions of the target object:
Ind. angular measuring system PMI360D-F130-IE8-V15-Y205400
Release date: 2010-01-12 11:45 Issue date: 2010-01-12 205400_ENG.xml