Percussion Play CAVATINA Service manual

1. Attach the steel legs to the
base of the instrument with
the M8 Nyloc Nuts and 2 part
security caps. (1.1) (See
Assembly Guide)
Ground Fixed
KS2 - 300mm
Ground Surface
KS1,2
KS1 - 450mm
KS1 –700mm
KS2 –850mm
Installation Instructions
(1.1) (1.1)
(1.2)
M10x200 Bolt
x2
M10 Nut
x4
6. Attach the 1 pair of beater
to the saddle strap on the leg.
(1.3)
Ground Fix
Components:
Instrument
Components:
(1.3)
19.5 Kg
2. Attach Ground Fixing posts
to legs(1.2) (See Ground Fix
Post Installation Sheet)
5. Once happy with location of
the Instrument, fill holes using
rapid hardening concrete. Be
sure to compact concrete
around legs and leave to dry
according to manufactures
guidelines.
3.Excavate 1 hole for the Steel
legs 250mm diameter by 350-
500mm deep depending on
Key stage, in desired location
upon decision from customer.
4. Locate (lower) leg into holes
making sure they are vertical
and level prior to concreting in
place.
Install Instrument
with 1.5m free space
(from widest point)
around it.
1.5m
1.5m
Pair Small Red
Beaters X1
Cavatina
Page 1 of 3
Weight of heaviest part 11kg (Cavatina)
BS EN 1176
Metric Conversion:
250mm/ 10”
300mm/ 12”
450mm/ 18”
700mm/ 28”
850mm/ 33”
1.5m/ 59”
Spares available form
percussionplay.com or from your
local distributor
M8 Nyloc Nut
x4
M6x20 Security Screw
x2
M6 Saddle Strap
x1
2 Part Cover Cap
x4

Ground Fixed
Assembly Guide PPSANS
(1.1)
M6 Saddle Strap
M10x200 Bolt
x2
M10 Nut
x4
Ground Fix
Components: 19.5 Kg
Pair Small Red
Beaters X1
Cavatina
Page 2 of 3
BS EN 1176
Thread Lock Solution
Required (Not Supplied)
Thread Lock Solution
Required (Not Supplied)
Spares available form
percussionplay.com or from your
local distributor
Instrument
Components:
M8 Nyloc Nut
x4
M6x20 Security Screw
x2
M6 Saddle Strap
x1
2 Part Cover Cap
x4
TX 30 Driver Bit
x1
TX 40 Driver Bit
x1
Tools:
PPCAVA SIDE
COMPONENTS LIST:
2 Part Cover Cap X4
M10 Nut X4
M10x200 Threaded Bar X2
Saddle Strap X1
M6x20 Pin torx X2
M8 Nyloc nut X4
PPCAVA FRONT

Ground Fixed
Components:
Ground Fix Post Installation
M10x200 Bolt
x2
M10 Nut
x4
Cavatina
Page 3 of 3
BS EN 1176
Insert M10x 200 Threaded
bar into pre drilled holes
in Ground Fixing Post
Fix M10x 200 Threaded
bar in place using M10
Nuts
Fill hole with fast drying
concrete to manufacturers
specifications.
350
50
350
250
Aggregate
Concrete
Excavate a hole with a
250mm diameter tapering
down to 350mm diameter
and 350mm depth
Compact base of hole with
50mm of aggregate.
Lower ground Fix post
attached of instrument
into hole (check
instrument straight and
level before filling with
concrete)
(1.1)
1 2 3
4
300mm min depth
5
Foundations should not present a hazard. These foundations are
recommended as a guide, for more information on foundation
details for various surface see Part 7 of BS EN 1176.
Metric Conversion:
50mm/ 2”
250mm/ 10”
300mm/ 12”
350mm/ 14”
400mm/ 16”
450mm/ 18”