Percussion Play Duo User manual

Ground Fixed
Duo
Page 1 of 3
KS2 - 400mm
Ground Surface
KS1,2
KS1 - 550mm
KS1 –700mm
KS2 –850mm
Installation Instructions
(1.1)
(1.2)
(1.3)
Instrument
Components:
M8x25 Security Screw
x8
M6x30 Security Screw
x4
M6 Saddle Strap
Pin Torx bit
x2
x2
M8 Lock washer
x8
M10x200 Bolt
x4
M10 Nut
x8
6. Attach the 1 pair of
beater to the saddle strap
on the leg. (1.3)
Ground Fix
Components: 20 Kg
2. Attach Ground Fixing
posts to legs(1.2) (See
Ground Fix Post Installation
Sheet)
1. Attach the steel legs to
the base of the instrument
with the M8x25 security
screws and lock washers.
(1.1) (See Assembly Guide)
5. Once happy with location
of the Instrument, fill holes
using rapid hardening
concrete. Be sure to
compact concrete around
legs and leave to dry
according to manufactures
guidelines.
3.Excavate 2 holes for the
Steel legs 200mm diameter
by 400-550mm deep
depending on Key stage, in
desired location upon
decision from customer.
4. Locate (lower) legs into
holes making sure they are
vertical and level prior to
concreting in place.
Install Instrument
with 1.5m free
space (from widest
point) around it.
1.5m
1.5m
Spares available form
percussionplay.co.uk or from
your local distributor
Pair Small Red
Beaters X2
Weight of heaviest part 14kg (Duo)
BS EN 1176

Ground Fixed
Instrument
Components:
Assembly Guide PPDUO
(1.1)
M8x25 Security Screw
x8
M6x30 Security Screw
x4
M6 Saddle Strap
x2
M8 Lock washer
x8
M8x25 Pin torx X8
M8 Lock washer X8
M10 Nut X8
M10x200 Threaded Bar X4
COMPONENTS LIST:
Saddle Strap X2
M6x20 Pin torx X4
PPDUO FRONT PPDUO SIDE
M10x70 Pin torx X2
M10 Barrel Nut Pin torx X2
M10x200 Bolt
x4
M10 Nut
x8
M10 Barrel Nut
x2
M10x70 Security Screw
x2
Ground Fix
Components: 20 Kg
Spares available form
percussionplay.co.uk or from
your local distributor
Pair Small Red
Beaters X2
Duo
Page 2 of 3
TX 30 Driver Bit
x1
TX 45 Driver Bit
Tools:
TX 40 Driver Bit
x1
BS EN 1176

Ground Fixed
Components:
Ground Fix Post Installation
(1.1)
M10x200 Bolt
x4
M10 Nut
x8
M10 Barrel Nut
x2
M10x70 Security Screw
x2
1 2 3 4
5
Insert M10x 200 Threaded
bar into pre drilled holes
in Ground Fixing Post
Fix M10x 200 Threaded
bar in place using M10
Nuts
Fill hole with fast drying
concrete to manufacturers
specifications.
Locate the Ground fix Post
into the leg of the
instrument.
Fix instrument to Ground
fix post using M10 bolt
and Barrel Nut and use
thread locking solution
to prevent fixings working
loose.
450
50
350
250
Aggregate
Concrete
Excavate 6 holes with a
250mm diameter tapering
down to 350mm diameter
and 450mm depth
Compact base of hole with
50mm of aggregate.
Lower ground Fix post
attached to instrument
into hole (check
instrument straight and
level before filling with
concrete)
6 7
Duplicate points 1-7. Duo requires 2
Ground Fix Posts
400mm min depth
Duo
Page 3 of 3
TX 45 Driver Bit
Tools:
x1
BS EN 1176