Petsafe ULTRALIGHT SONIC BARK CONTROL User manual

ULTRALIGHT SONIC
BARK CONTROL
QUICK GUIDE
LÉGER DE CONTRÔLE
SONORE DES ABOIEMENTS
GUIDE D’UTILISATION
ULTRALIGHT AKUSTISCHE
BELL-KONTROLLE
ULTRALIGHT SONIC
BLAF CONTROLE
KORTE HANDLEIDING
CONTROL ULTRALIGERO
DE LADRIDOS DE SONIC
GUÍA RÁPIDA
SISTEMA ACUSTICO
ANTIABBAIO ULTRALEGGERO
GUIDA RAPIDA
COLEIRA ANTI-LATIDO
ULTRALIGHT (LEVE)
GUIA RÁPIDO

2
ENGLISH
Read training manual and quick guide before attempting to use the product.
FRENCH
Lisez le manuel de dressage ainsi que le guide d’utilisation avant d’essayer
d’utiliser ce produit.
SPANISH
Lea el manual de aprendizaje y la guía rápida antes de utilizar el producto.
GERMAN
Lesen Sie das Trainingshandbuch und die Kurzanleitung, bevor Sie ver-
suchen, das Gerät zu benutzen!
DUTCH
Lees de trainingshandleiding en de quick guide alvorens u het product gaat
gebruiken.
ITALIAN
Leggete il manuale di addestramento e la guida rapida prima di utilizzare
il prodotto.
PORTUGESE
Antes de utilizar o produto leia as instruções no manual de treino e no guia
de consulta rápida.

3
STEP 1 BATTERY ACTIVATION
The battery module is installed in your UltraLight Sonic
Bark Control unit. A removable protective film on the
contact side of the battery prevents activation of the unit.
Introduce your dog to the bark control unit as described in
the training manual before removing the protective film.
To remove the battery, insert a coin in the slot on top of the
battery module, push down slightly and turn counter-clockwise.
Flip battery to contact side. To remove the protective film, lift
the red tab and peel off the film.
To re-install battery, align the arrow on the battery module with the triangle
on the unit. Using a coin, push down and turn clockwise, until the arrow on
the battery module lines up with the "Lock" on the unit.
Battery life is dependent on the number of corrections your dog receives, but
on average the life should be 1 month.
STEP 2 TEST UNIT
Hold your finger over the speaker to muffle the sound
when testing the unit. Blow across the microphone.
The unit should emit a sharp sound. If you do not
hear a tone – check the battery and repeat the test. microphone speaker

4
STEP 3 SET MICROPHONE SENSITIVITY LEVEL
Locate the microphone High/Low switch on the side
of the unit. Begin with the setting in the low position.
If the unit does not emit a sound correction when the
dog barks, move the switch to the high setting.
STEP 4 ATTACH TO COLLAR
Note: Do not place unit on your dog without reading the
Training Manual.
Collar material thickness should be approximately
1/16", and no wider than 1". Slide the collar under all
four clips. Be sure the unit is placed in the center of the
collar, opposite of the buckle, and fits snuggly against
the middle of the dog’s throat. The microphone may
not activate properly if the unit is rotated to the side
or if the collar hangs too loosely. Remove any tags from the collar to avoid
triggering a false stimulation.

5
CAUTIONS: To prevent damage to the inner ear, do not place the unit next to
your ear, the ear of any other human, or your pet’s ear. Keep out of the reach of
children. Do not allow dog to chew on unit.Unit is not waterproof - do not immerse
in water. If unit gets wet, you may remove battery, shake out excess water, and let
unit dry before attempting to use again.
STEP 5 OBSERVE FIRST REACTION
Observe your dog's first reaction to the correction. As excited as your dog
may get, you must remain calm. Yelping or cowering is a normal response.
Your pet must clearly understand the reason for the stimulation in order
to change his behavior. Modifying your dog’s barking behavior may take
several days.
Each dog will need different lengths of time to learn to control their
nuisance barking.