Philips CID3688/00 User manual

www.philips.com/welcome
Register your product and get support at CID3688
www.philips.com/welcome
Register your product and get support at
ENG Quick Start Guide
3
2
1
a
b
5
4English
Install the car audio 1
Connect wires
1Check the car’s wiring carefully, then
connect them to the two supplied ISO
wires. a
Connector Connect to
1CANBOX
2Redwire The +12V power terminal
which is live in the accessor y
(ACC) position of the
ignition switch
If there is no accessor y
position, connect to the
+12V car battery terminal
that is always live. Be sure
to connec t the black ground
(earth) lead to a metal surface
RIWKHFDUÀU VW
3 Orange
wire
Illumination switch
4Blackwire A metal surface of the car
Firs t connec t the black
ground (ear th) lead, then
connect the yellow and red
power supply leads.
5YellowwireThe +12V car batter y which
is live at all times.
6Bluewire The electric antenna control
lead or power supply lead of
the antenna booster
If there is no electric antenna
or antenna booster, or it is
manually operated telescopic
antenna , it is not necessar y to
connect this lead.
7CANBOX
8 Green and
green/black
wires
Left speaker (Rear)
9 White and
white/black
wires
Left speaker (Front)
10 G ray and
gray/black
wires
Right speaker (Front)
11 Purple and
purple/black
wires
Right speaker (Rear)
2Connec t the other end of the two ISO
connectors to the car audio system. b
3If necessary, do other connections: c
Mount in the dashboard 2
1If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car batter y.
2Ensure that the hor izontal slant of the car
dashboard opening is between 0 and
20 degrees. The unit cannot be used if
the dashboard opening’s slant angle is
above 20 degrees.
3Install the mounting bolt and place the
supplied rubber cap over the end of the
mounting bolt.
4 6OLGHWKHXQLWLQWRWKHGDVKERDUGDQGÀ[LW
WRWKHFDUZLWKÀYHVFUHZV
5Reconnec t the negative ter minal of the car
battery.
Turn on
Caution
Risk of road accidents! Never watch video or

adjust settings while you drive.
1Press and hold /MUTE/VOL to turn on
the unit .
The available OSD (On-Screen Display)»
languages are displayed.
2Tap a language to select.
The OSD language is changed to the»
selected language immediately.
To turn off the unit, press and hold /MUTE/
VOL.
Adjust screen
To adjust screen brightness
1Press DISP/ /to show the brightness bar.
2Tap / to adjust the value.
3Press DISP/ /WRFRQÀUP
To turn on/off the screen, press and hold DISP/ / .
Set date and time
1Tap the upper lef t corner to display the
main menu.
2Tap in the middle right side of the screen.
The second main menu is displayed.»
3Tap [Settings].
4Tap [Time].
The date/time setup menu is displayed.»
Set date
1Tap [Date].
2Tap on the displayed date information.
A submenu is displayed.»
3Tap or to set year, month and day.
Set clock mode
1Tap [Clock mode].
2Tap on [12Hr] or [24Hr] to select clock
mode.
Set time
1Tap [Time].
2Tap on the displayed time.
A submenu is displayed.»
3Tap or to set hour and minute.
Use map
Note
You may need to upgrade the map before

using it (see “ Upgrade the map” section).
1Tap the upper lef t corner to display the
main menu.
2Tap [Navigation].
The navigation menu is displayed in a»
few seconds.
3Refer to the map manual (in Chinese) to
operate the navigation tool.
Listen to Radio
1Tap to display the home menu.
2Tap [Radio].
»Band and frequency information is
displayed.
3Tap on FM or AM to select band:
4 %ULHÁ\WDS or to tune to a radio station
by step.
Play disc 3
You can play video, audio or images stored on the
following discs:
DVD video, DVD-R, DVD-RW
VCD
Audio CD, CD -R , CD- RW
1Inser t the disc into the disc slot with the
label side facing up.
Play starts automatically.»
To remove the disc, press».
Connect USB device 4
1Inser t your USB device to the USB socket.
Play starts automatically.»
Remove the USB device
1Switch to another (non-USB) source.
2Remove the USB device.
Insert SD/MMC card 5
1Open the SD/MMC card cover.
2Inser t the SD/MMC card into the SD/MMC
card slot.
Play starts automatically.»
Remove the SD/MMC card
1Switch to another sour ce.
2Press the card until you hear a click sound.
The card is now disengaged.»
3Remove the SD or MMC card.
Play with Bluetooth device
Pair the Bluetooth-enabled devices
To connect your Bluetooth device to the unit, you
need to pair the device to the unit. Pairing needs
only to be done once.
You can pair up to eight devices.
1Turn on the Bluetooth function on the
device.
© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
CID3688_00_QSG_V1.0
h
i
j
k
b
a
c
d
e
f
g
c
Yellow Green Blue
Red
Black Yellow
Blue/white
Pink
Green/white
Gearbox
AV system
AUX
Red
White Yellow
Red
White Yellow
Rear display
Wireless headphone
Yellow
Black
GPS antenna
Amplifier
White White
Red Red
Brown
Radio antenna
L
a
b
e
l
s
i
d
e
2Search for Bluetooth device with the
device.
3Select “CID3688” in the pairing list.
4Enter default password “0000”.
if pairing succeeds. phone call record is»
displayed.
Make a call
1Pair the phone with the unit.
2Tap to display the home menu.
3Tap [Bluetooth].
The Bluetooth menu is displayed.»
4Tap or to select the paired phone, then
tap .
5Tap or to search for phone number
from the following list:
Or tap to dial number directly, then tap
to dial.
Receive call
By default, all incoming calls are received
automatically.
1If there is incoming call, [Incoming call...]
ÁDVKHVRQWKHVFUHHQ6SHDNLQWRWKH
Bluetooth microphone.
2When conversation ends, tap (red) to
terminate the call.