Philips SmartMeeting PSE0501 User manual

Get your smart AI meeting
assistant
Start your free trial now!
1Go to https://smartmeeting.sembly.ai
2Sign up
3 )ĚŊâľŊüâłâľÿ½ēĚŏę×âľġõŮġŏľÞâŧÿØâַŮġŏؽĚžĚÞÿŊġĚ   
the packaging or the device itself)
4Use the code “SM2022D1”to activate your Team Plus plan (unlimited
 Ěŏę×âľġõęââŊÿĚöłÿĚŊüâžľłŊęġĚŊü֤ŊüâĚŏĻŊġԞęââŊÿĚöłĻâľęġĚŊüָ
User
manual
IN R12V
2 4 5 11
8
76
910 11 12 13
3
6
1. Speaker
2. USB Type-C port (input)
3. Reset
4. Power socket
5. USB Type-C port (output)
6. Microphones
7. USB status LED
8. Battery status LED
9. Power
10. Volume down
11. Volume up
12. Mute
13. Bluetooth
© 2022 Spee ch Proces sing So lutions GmbH. All rights reserve d.
This product has been manufactu red by and is sold under the re spons ibility of Speech Proce ssing
Solut ions GmbH, and Speech Process ing Solutions GmbH is the warr antor in relati on to this p roduc t.
Specicat ions are subject to chan ge with out not ice. Philips and the Philip s shield emblem a re
regis tered trademarks of Koninklijke Philips N.V. and are used u nder license.
Document version 1.0, 03/02/22 For more support visit
www.dictation.philips.com/pse0501help
User manual
a
n
u
a
a
l
l
Wireless Conference
Microphone
with Sembly Meeting
Assistant
PSE0501
SmartMeeting
pse0501.indd 4
pse0501.indd 4
02/03/2022 14:16:36
02/03/2022 14:16:36

ġľâłâŊŊüâÞâŧÿØâ֤Ļľâłł½ĚÞüġēÞŊüâľâłâŊ
button on the back side of your device by using a
łę½ēē֤ĻġÿĚŊâÞġ×čâØŊ֤õġľâŭ½ęĻēâ֤½Ļ½ĻâľØēÿĻ
Press to mute yourself
Press or to change
the volume of the speaker
IN R12V
R
IN R12V
IN
You can use the “IN”USB Type-C port to connect
a second PSE0501 device (cable not included) to
further increase the range
Hold õġľԛłâØġĚÞ֤
to disconnect from
the current device
5
4
Go to the bluetooth
settings of your device
and choose "PSE0501"
in the list
3
1 sec
starts blinking blue and
the speaker says "pairing"
2
1
6
stops blinking and
lights up blue. The
speaker says "connected"
ġõŏēēŮŏĚĻ½ÿľ֤öġŊġŊüâ
bluetooth settings of your
device and remove "PSE0501"
1 sec
Press to turn
the device on
IN R12V
Connect the USB cable to the “USB / OUT”
port of the device and to a computer.
Note: The device can only be charged via
the AC adapter
You can now use the
device with various
ęââŊÿĚöłġõŊŨ½ľâ֤×Ů
selecting "PSE0501"
12
3
1 sec
Press to turn the device on
IN R12V
123
Connect the AC adapter to the
device and a power socket
The LEDs on the top of the
device indicate the battery
status and stop blinking after
the device is fully charged
Connect the correct plug
to the AC adapter
pse0501.indd 8
pse0501.indd 8
02/03/2022 14:16:38
02/03/2022 14:16:38

f
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
pse0501_fcc-ce_warning-card.indd 1
pse0501_fcc-ce_warning-card.indd 1
03/03/2022 13:54:38
03/03/2022 13:54:38

Manufactured for: Speech Processing Solutions GmbH,
Gutheil-Schoder-Gasse 8–12,
1100 Wien, Österreich
www.philips.com/dictation
Brand: Philips
Product name: Wireless Conference Microphone
Model: PSE0501
Operating temperature: 5° – 45° C / 41° – 113° F
Maximum Bluetooth
transmit power:
+6 dBm
The product shall only be connected to a USB interface of version USB2.0
or higher. Charging via USB is not supported, the device can only be
charged via the included AC adapter.
For this device, Head SAR and Body SAR was performed with the device
congured in the positions according to EN62209-1:2016 & EN62209-
2:2010, and Body SAR was performed with the device 0mm from the
phantom. Body SAR was also performed with the headset attached and
without.
pse0501_fcc-ce_warning-card.indd 2
pse0501_fcc-ce_warning-card.indd 2
03/03/2022 13:54:38
03/03/2022 13:54:38