Philips HR7723/00 User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
Cucina Food processor
HR7723/00
HR7724/16
4322 277 01090
02/11
PRODUCT INFORMATION
- The food processors are equipped with mechanical and
thermal safety switches.
- Product meets the requirements regarding interference
suppression on radio and TV.
- After the product has been repaired, it should function
properly and has to meet the safety requirements as
laid down officially established at this moment.
Automatic resettable cut-out (part of item 7)
- To prevent damage due to overheating, the appliance
has been equipped with an automatic cut-out system.
This system will automatically cut off the power supply
when the appliance overheats.
If the appliance suddenly stops running:
- Unplug the appliance
- Set the knob to position 0
- Let the appliance cool down for 15 minutes
- Plug the appliance in again
- Switch the appliance on again
Safety lock (item 1)
- Place the lid on the bowl in the right position.
The appliance will only function if the arrow on the
applinace is directly opposite the mark on the lid of
the food processor bowl and the same holds for the
other accessoires. The built-in safety lock will now be
deblocked and you can turn the appliance on.
Note that if both the blender jar and the bowl have been
correctly mounted, only the blender will function.
Important:
- If the appliance is used without the blender jar, the
appliance will not function if the screw cap has not been
screwed onto the attaching hole for the blender.
TECHNICAL INFORMATION
- Motor power : HR7723 - 600 W
HR7724 - 700 W
- Voltage : 230 V
: 110 V
- Frequency : 50 / 60 Hz
- Colour : White
- Cordset : 125 cm
- Speed settings : 2 speeds + pulse
- Bowl capacity : 2.5 l dry ingredients
1.0 l liquids
- Blender capacity : 1.0 l liquids
2.0 l (max. contents)
- Speeds unloaded : blender drive shaft 17000 rpm (max)
acc. drive shaft 2150 rpm (max)
acc. drive shaft 1400 rpm (min)
- Weight in fancy box : HR7723/24 - 5100 g
- Dimensions : HR7723/24 - 420 x 280 x 360
(l x w x h)
- SAP coding : HR7723/00
HR7724/16

DISASSEMBLY- AND RE-ASSEMBLY ADVISE
- A separate drawing shows how to disconnect the speed
selection knob.
- The blender coupling on the motor shaft has been provided
with the customary left-hand thread.
The drive coupling (item 11) can be detached by means of
a hammer and a screwdriver. Strike the screwdriver with a
short sharp blow and remove the drive coupling. Or block
the acc. drive wheel (item 23) and thereby the rotor shaft,
by sticking a pin through the hole (5 mm dia.) in the bottom
plate.
- The top housing (item 29) can be removed by detaching
the snap connections by sticking a pin (or a screwdriver)
through the small round holes (3 mm dia.) in the bottom
plate (item 27) and the housing (item 12).
The arrows in the drawing show the locations of the holes.
- In order to replace the speed selection knob, the locking
lever (item 33) must be placed in its lowest position.
- The accessory drive shaft (item 15) has a locking piece
(item 14).
- The assembly of the accessories depends on the national
version.
- For specific versions, the component configuration may
differ from the one shown on the exploded view.
However, the actual components can be distinguished by
their code numbers.
- Make sure that all functions, including the safety devices,
are working correctly after you have completed the repair.
REPAIR INSTRUCTION
- No specific issues
OPTIONAL (ACCESSORIES)
- No specific issues
PARTS LIST
Speed High
and Pulse
Change-over switch
in braking position
Rotor
Speed Low
brown
MAINS
red
white
yellow
brown
black
F1
F2
violet N
BF
B
N1
M1
L2
R1
470k
D1
1N5406
C1
blue
R
NL1
HR7723 / HR7724
F2
F1
HR7723/00 / HR7724/16
Pos Service code Description
1
2
3
4
5
7
8
9
10
11
12
13
14
15
16
17
18
19
20
4203 065 62110
4822 214 12762
4203 065 62120
4822 532 13008
4822 462 11074
4822 361 11081
4822 361 11082
4822 466 11949
4203 065 60300
4822 502 14593
4203 065 62130
4203 065 64570
4822 214 12767
4822 402 11076
4822 535 10548
4203 065 62070
4822 466 11948
4822 535 10549
4822 530 10492
4822 492 11649
Print + switch lever
Print plate brake
Coupling lever
Rubber piece
Air tunnel
Motor 230 V
Motor 110 V
Coupling fork
Flex
Motor screw assy
Blender coupling
Housing
Print plate
Locking piece
Drive spindle
Rubber sealing
Locking plate
Spindle assy
Rubber tube
Compression spring
Pos Service code Description
21
22
23
24
25
27
28
29
30
31
33
4822 528 11265
4822 358 10257
4822 528 11266
4822 520 10851
4822 466 11947
4203 065 64610
4203 065 64620
4203 065 64630
4203 065 64640
4822 492 11648
4203 065 64600
4203 065 62180
4203 065 62200
Coupling piece
Tooth belt
Belt wheel
Bearing
Mounting plate
Bottom plate
Blender cover
Housing top HR7723
Housing top HR7724
Snap return spring
Switch knob HR7723
Switch knob HR7724
Locking lever
2-4

EXPLODED VIEW
3-4
HR7723/00 / HR7724/16
1
3
7
5
4
2
9
8
10
27
25
12
14
13
15
16
17
19
18
21
30
29
33
28
20
22
23
24
19
31
11

PARTS LIST & EXPLODED VIEW ACCESSORIES
56
60
59
62
64
65
66
67
68
69
63
55
58
52
74
75
73
70
71
72
4-4
HR7723/00 / HR7724/16
Pos Service code Description
52
55
56
58
59
60
62
63
64
65
4822 462 11083
4203 065 61860
4203 065 60170
4203 065 60160
4203 065 64510
4203 065 64390
4203 065 63800
4203 065 64520
4203 065 61840
4203 065 61960
Insert of lid
Storage box (4 acc.)
Kneading/mixing knife
Metal knife
Bowl (dry 2.5 l)
Emulsifying disc
Mono pusher
Bowl cover
Patato grating disc (opt.)
Grating disc (fine/very fine)
Pos Service code Description
66
67
68
69
70
71
72
73
74
75
4203 065 61950
4203 065 61970
4203 065 61980
4203 065 61830
4203 065 64530
4203 065 64540
4203 065 64550
4203 065 61890
4203 065 62220
4203 065 64650
Slicing disc (fine/medium)
Grating disc (coarse/medium)
Combi disc (slicing/grating)
French fries (opt.)
Insert of cover
Cover
Beaker
Sealing ring
Driven coupling
Knife unit