Philips PLFRESNEL 1 LED LUMINAIRES Instruction Manual

Philips Selecon Offices
The material in this manual is for information purposes only and is subject to change without notice. Philips
Selecon assumes no responsibility for any errors or omissions which may appear in this manual. For comments and
suggestions regarding corrections and/or updates to this manual, please visit the Philips Selecon web site at
www.seleconlight.com or contact your nearest Philips Selecon office.
El contenido de este manual es solamente para información y está sujeto a cambios sin previo aviso. Philips
Selecon no asume responsabilidad por errores o omisiones que puedan aparecer. Cualquier comentario, sugerencia
o corrección con respecto a este manual, favor de dirijirlo a la oficina de Philips Selecon más cercana.
Der Inhalt dieses Handbuches ist nur für Informationszwecke gedacht, Aenderungen sind vorbehalten. Philips
Selecon uebernimmt keine Verantwortung für Fehler oder Irrtuemer, die in diesem Handbuch auftreten. Für
Bemerkungen und Verbesserungsvorschlaege oder Vorschlaege in Bezug auf Korrekturen und/oder
Aktualisierungen in diesem Handbuch, moechten wir Sie bitten, Kontakt mit der naechsten Philips Selecon-
Niederlassung aufzunehmen.
Le matériel décrit dans ce manuel est pour information seulement et est sujet à changements sans préavis. La
compagnie Philips Selecon n'assume aucune responsibilité sur toute erreur ou ommission inscrite dans ce manuel.
Pour tous commentaires ou suggestions concernant des corrections et/ou les mises à jour de ce manuel, veuillez s'il
vous plait contacter le bureau de Philips Selecon le plus proche.
Note: Information contained in this document may not be duplicated in full or in part by any person without prior written
approval of Philips Selecon. Its sole purpose is to provide the user with conceptual information on the equipment mentioned. The
use of this document for all other purposes is specifically prohibited.
Document Number: 02.9701.0001
Version as of: 20 February 2013
PLFRESNEL1 LED Luminaire Installation & User’s Manual
©2013 Philips Group. All rights reserved.
Philips Selecon - Dallas
10911 Petal Street
Dallas, TX 75238
Tel: [phone]
Fax: [phone]
Philips Selecon - Auckland
19-21 Kawana Street
Northcote, Auckland 0627
New Zealand
Tel: [phone]
Fax: [phone]
Philips Selecon - New York
267 5th Ave, 4th Floor
New York, NY 10016
Tel: [phone]
Fax: [phone]
Philips Selecon - Europe
Rondweg zuid 85
Winterswijk 7102 JD
The Netherlands
Tel: [phone]
Philips Selecon - Asia Limited
Unit C, 14/F, Roxy Industrial Centre
No. 41-49 Kwai Cheong Road
Kwai Chung, N.T., Hong Kong
Tel: [phone]
Fax: [phone]
Website:
www.seleconlight.com

1
PLFRESNEL1 LED Luminaires Installation & User’s Manual
IMPORTANT INFORMATION
Warnings and Notices
Additional Resources for DMX512
For more information on installing DMX512 control systems, the following publication is available for purchase
from the United States Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guide
for Users and Installers, 2nd edition" (ISBN: 9780955703522). USITT Contact Information:
USITT
315 South Crouse Avenue, Suite 200
Syracuse, NY 13210-1844
Phone: [phone] or 1.315.463.6463
www.usitt.org
Philips Selecon Limited Three-Year Warranty
Philips Selecon offers a three-year limited warranty of its luminaires against defects in materials or workmanship
from the date of delivery. A copy of the Philips Selecon three-year limited warranty containing specific terms and
conditions can be obtained from the Philips Selecon web site at www.seleconlight.com or by contacting your local
Philips Selecon office. PLFRESNEL1 LED Luminaire powerful LED engine offers exceptional performance and
life. Under normal operating conditions, our LED engine has a life expectancy in excess of 50,000 hours, however
under worst case operating conditions with the luminaire set to continuous full output it is possible that a small
percentage of LED’s may require replacement sooner. The Philips Selecon three-year limited warranty includes our
guarantee against premature failure of the LED engine.
When using electrical equipment, basic safety precautions should always be followed including the following:
a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b. Do not use outdoors.
c. Do not mount near gas or electric heaters.
d. Equipment should be mounted in locations and at heights where it will not readily be subjected to
tampering by unauthorized personnel.
e. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
f. Do not use this equipment for other than intended use. This equipment is not for residential
installation or use.
g. Refer service to qualified personnel.
SAVE THESE INSTRUCTIONS.
WARNING: You must have access to a main circuit breaker or other power disconnect device
before installing any wiring. Be sure that power is disconnected by removing fuses or turning the
main circuit breaker off before installation. Installing the device with power on may expose you to
dangerous voltages and damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code® and local codes for cable specifications. Failure to
use proper cable can result in damage to equipment or danger to personnel.
WARNING: This equipment is intended for installation in accordance with the National Electric
Code® and local regulations. It is also intended for installation in indoor applications only. Before
any electrical work is performed, disconnect power at the circuit breaker or remove the fuse to avoid
shock or damage to the control. It is recommended that a qualified electrician perform this
installation.

Installation & User’s Manual PLFRESNEL1 LED Luminaires
2TABLE OF CONTENTS
TABLE OF CONTENTS
Philips Selecon Offices.................................................................................................................................... 0
IMPORTANT INFORMATION
Warnings and Notices...................................................................................................................................... 1
Additional Resources for DMX512................................................................................................................. 1
Philips Selecon Limited Three-Year Warranty............................................................................................... 1
TABLE OF CONTENTS
PREFACE
About this Manual .................................................................................................................................................. 4
Accessories............................................................................................................................................................. 4
PLFRESNEL1 LED Luminaire Power Input Cables...................................................................................... 4
PLFRESNEL1 LED Luminaire Lens Accessories.......................................................................................... 4
PLFRESNEL1 LED Luminaire Clamps ......................................................................................................... 4
PLFRESNEL1 LED Luminaire USB Luminaire Software Cable .................................................................. 4
PLFRESNEL1 LED Luminaire Top Box Assembly....................................................................................... 4
PLFRESNEL1 LED LUMINAIRE OVERVIEW
PLFRESNEL1 LED Luminaire Components......................................................................................................... 5
Major Luminaire Components ........................................................................................................................ 5
Top Box (PLICB) Luminaire Connections ..................................................................................................... 6
LCD Display / Menu System .......................................................................................................................... 6
INSTALLATION AND SET UP
Power Requirements............................................................................................................................................... 7
Connecting Power................................................................................................................................................... 7
Connecting to the DMX512 Network..................................................................................................................... 8
Mounting ................................................................................................................................................................ 9
Using Supplied C-Clamp................................................................................................................................. 9
Safety Cable Use ............................................................................................................................................. 9
Pan and Tilt Adjustments...................................................................................................................................... 10
Pan Adjustment ............................................................................................................................................. 10
Tilt Adjustment.............................................................................................................................................. 10
BEAM ADJUSTMENTS
Beam Adjustments................................................................................................................................................ 11
Barndoor Assembly.............................................................................................................................................. 11
OPERATION AND PROGRAMMING
LCD Menu Operation........................................................................................................................................... 12
LCD Menu System............................................................................................................................................... 13
Menu Structure.............................................................................................................................................. 14
Security................................................................................................................................................................. 16
Passwords...................................................................................................................................................... 16
Security Levels.............................................................................................................................................. 17
Locking Fixture............................................................................................................................................. 17
Presets................................................................................................................................................................... 17
Presets Types................................................................................................................................................. 17
Editing Preset Names .................................................................................................................................... 18
Settings ................................................................................................................................................................. 18

3
PLFRESNEL1 LED Luminaires Installation & User’s Manual
DMX CONTROL
16-Bit Mode.......................................................................................................................................................... 20
8-Bit Mode............................................................................................................................................................ 22
DMX 3-Channel (3-Chan) Mode ......................................................................................................................... 24
Lighting Console Settings for Preset White......................................................................................................... 25
PLFRESNEL1 LED Luminaire DMX Timing Channel Detail............................................................................ 25
CLEANING AND CARE
Special Cleaning and Care Instructions................................................................................................................ 31
Service and Maintenance...................................................................................................................................... 31
Accessories........................................................................................................................................................... 31
TROUBLESHOOTING
Troubleshooting Guide......................................................................................................................................... 32
TECHNICAL SPECIFICATIONS
PLFRESNEL1 LED Luminaire Operational Specifications................................................................................ 33
PLFRESNEL1 LED Luminaire Dimensions........................................................................................................ 33

Installation & User’s Manual PLFRESNEL1 LED Luminaires
4PREFACE
PREFACE
1. About this Manual
The document provides installation and operation instructions for the following products:
• PLFRESNEL1 LED Luminaire (PLFR1-03).
Please read all instructions before installing or using this product. Retain this manual for future reference. Additional
product information and descriptions may be downloaded at www.seleconlight.com
Note: All PLFRESNEL1 LED Luminaires are universal voltage (100VAC to 240VAC, Auto-ranging).
2. Accessories
Contact your Authorized Philips Selecon Dealer for price and availability of all accessories for PLFRESNEL1 LED
Luminaires. Additional information can be found on the Philips Selecon web site at www.seleconlight.com.
PLFRESNEL1 LED Luminaire Power Input Cables
PLFRESNEL1 LED Luminaire Lens Accessories
PLFRESNEL1 LED Luminaire Clamps
PLFRESNEL1 LED Luminaire USB Luminaire Software Cable
PLFRESNEL1 LED Luminaire Top Box Assembly
Part Number Description
PC1BE PLFRESNEL1 LED Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon without
Connector (user to supply AC connector)
PC1GP PLFRESNEL1 LED Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon with Stagepin
Connector
PC1GTL PLFRESNEL1 LED Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon with Twistlock
Connector
PC1GR PLFRESNEL1 LED Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon with Edison
Connector
PC3PC PLFRESNEL1 LED Luminaire PowerCon Male to PowerCon Female 2.5 Meter Cable for
interconnection between units
Part Number Description
20BDMF Acclaim Fresnel Barndoor, 4 Way, Black
Part Number Description
SC Selecon Molded Yoke rated C-Clamp
MC Mega Claw, Black Anodized
Part Number Description
PLUPLD USB Luminaire Software Programming Kit (for updating or reloading luminaire software only) - include
USB to DMX dongle, Uploader Program, and Carry Bag
Part Number Description
PLICB Spare Top Box (Interconnect) Assembly

PLFRESNEL1 LED Luminaire Components 5
PLFRESNEL1 LED Luminaires Installation & User’s Manual
PLFRESNEL1 LED LUMINAIRE OVERVIEW
1. PLFRESNEL1 LED Luminaire Components
Major Luminaire Components
Figure 1: PLFRESNEL1 LED Luminaire Components
For the LCD Display Menu System, refer to "LCD Display / Menu System" on page 6 for more information.
Front of Unit
Rear of Unit
Top Box Assembly (PLICB)
(AC Input/Thru and DMX In/Out Connections)
Safety Cable
Anchor Point
Beam (Spot/Flood)
Yoke Locking Handle
LCD Display /
Menu System
Multi-Conductor
Fixture Connection
Accessory Holder
(with latching door)
Adjustment

Installation & User’s Manual PLFRESNEL1 LED Luminaires
6PLFRESNEL1 LED LUMINAIRE OVERVIEW
Top Box (PLICB) Luminaire Connections
Figure 2: Top Box (PLICB) Connections
LCD Display / Menu System
Figure 3: PLFRESNEL1 LED Luminaire LCD Display & Menu System
DMX512 Output/Thru
DMX512 Input
AC (Power) Output
AC (Power) Input
Multi-Conductor Top Box
to Luminaire Connection
Multi-Conductor Top Box
to Luminaire Connection
Side View 1
Side View 2
1) LCD Display (Menu System)
2) Preset / Intensity / Menu Access Buttons
3) Function (Menu System) Select Push Buttons
1
Note: For Menu operation and programming details,
refer to "LCD Menu Operation" on page 12.
2
3

Power Requirements 7
PLFRESNEL1 LED Luminaires Installation & User’s Manual
INSTALLATION AND SET UP
1. Power Requirements
The PLFRESNEL1 LED Luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire contains
an auto-ranging power supply. Depending on supply voltage, each luminaire can draw up to 1.5 amps.
WARNING! *These figures are based on the Maximum Allowable Input Current of 20 Amps (and the maximum
power supply limit of 150 Watts). Do not overload circuits!
2. Connecting Power
Units can be powered in one of two ways:
• Direct connection to a AC power source using an AC input cable.
• Daisy chain connection using a interconnect AC cable.
If the unit is supplied with an AC input cable but you did not order an AC input connector, Table 2 on page 8
describes how to connect power to your PLFRESNEL1 LED Luminaire. Field wiring of the PLFRESNEL1 LED
Luminaire is straight forward. A total of 3 wires/conductors need to be brought to the unit. The following wiring
scheme is required:
Table 1: PLFRESNEL1 LED Luminaire Voltage vs. Current
Voltage
(AC) Total Current (A)
Maximum
number of
unitsthatcan
be linked
together*
Voltage
(AC) Total Current (A)
Maximum
number of
unitsthatcan
be linked
together*
100 1.50 13 180 0.83 24
110 1.36 14 190 0.79 25
120 1.25 16 200 0.75 26
130 1.15 17 210 0.71 28
140 1.07 18 220 0.68 29
150 1.00 20 230 0.65 30
160 0.94 21 240 0.63 32
170 0.88 22
IMPORTANT AC POWER CONNECTION NOTES:
a. When using the daisy-chain connection method, ONLY connect PLFRESNEL1 LED Luminaires to
AC Output Connection of PLFRESNEL1 LED Luminaires. DO NOT CONNECT OTHER TYPES
OF LUMINAIRES OR DEVICES!
b. Use only use approved cable types.
c. Do not overload circuits!
d. Do not connect PLFRESNEL1 LED Luminaires to dimmed circuits.
e. The MAXIMUM allowable number of PLFRESNEL1 LED Luminaires which can be 'daisy-
chained' on one power feed are listed in Table 1, above. DO NOT EXCEED!

Installation & User’s Manual PLFRESNEL1 LED Luminaires
8INSTALLATION AND SET UP
Table 2: PLFRESNEL1 LED Luminaire AC Input
Connections
3. Connecting to the DMX512 Network
Basic DMX512 installation consists of connecting multiple PLFRESNEL1 LED Luminaires together (up to 30
luminaires) in "daisy-chain" fashion. A cable runs from the control console (or DMX512 control source) to the DMX
connector on the first PLFRESNEL1 LED Luminaire. Another cable runs from the other DMX connector on the first
unit to a DMX connector on the next PLFRESNEL1 LED Luminaire (or DMX512 device to be controlled).
Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on
page 1. For PLFRESNEL1 LED Luminaire DMX Mapping, refer to "DMX CONTROL" on page 20.
Figure 4: PLFRESNEL1 LED Luminaires - DMX512 Connections
Wire Color Purpose
Brown Main / Line (120 to 240VAC)
Blue Neutral
Green/Yellow Ground
Neutral Main /
Ground / Earth
Line
AC Input Connector
(on back of unit)
DMX512
DMX512 (out from first
to second luminaire) DMX512 (out to the next luminaire or
DMX512 controlled device)
PLFRESNEL1 LED Luminaires
(from console or
control device)
DMX512 Connections
Data Thru
Cable Pinout
Male Conn
Pin 1
Common
(Drain)
Pin 2
Data (-)
Pin 3
Data (+)
Pin 4
Not Used
Pin 5
Not Used
Data In
Cable Pinout
Female Conn
1
234
51
2
3
4
5

Mounting 9
PLFRESNEL1 LED Luminaires Installation & User’s Manual
4. Mounting
WARNING! Before attempting any installation or service, disconnect all power at power source. Dimming the
luminaire does not disconnect power. Installation and service should only be performed by a trained and qualified
professional.
Using Supplied C-Clamp
As illustrated in Figure 5, at yoke assembly, thread clamp mounting bolt (with washer installed) through center
clamp mounting hole at top of yoke, through Top Box Assembly, and thread bolt into C-Clamp. Securely tighten bolt
(by hand) into clamp (but do not overtighten).
Figure 5: Luminaire Mounting
To mount on a telescopic stand, reverse the yoke under the luminaire and bolt to stand. Please note luminaire
orientation (see note in Figure 5) for proper cooling.
Note: After installing Clamp and Top Box assembly, connect luminaire cable assembly to Top Box Assembly before
mounting luminaire. Please note that the cable connector is keyed.
Safety Cable Use
The supplied safety cable MUST always be used when rigging luminaires on bars, truss, etc. (as shown in Figure 6).
The supplied safety cable is recommended for all hanging installation and may be required by national and local
Yoke Assembly
Center Clamp Mounting Hole (13 mm)
NOTE: To allow for proper cooling, make sure
luminaire head is orientated as shown (with
forward cooling vents pointed upwards).
Top Box Assembly
C-Clamp
Flat Washer
C-Clamp Bolt*
Top Box Assembly
Luminaire Cable
WARNING! *When installing a C-Clamp (or hook,
or other type of clamp) with the Top Box Assembly
as shown, you MUST use the C-Clamp Bolt
supplied with the fixture. Failure to do so may result
in damage to the Top Box Assembly or cause the
luminaire to dislodge from the clamping device.
Assembly

Installation & User’s Manual PLFRESNEL1 LED Luminaires
10 INSTALLATION AND SET UP
codes. Loop or attach safety cable to luminaire safety cable anchor point as shown and attach to structure. You should
always consult and follow all local and national codes and regulations for mounting and installation of luminaire.
5. Pan and Tilt Adjustments
Pan Adjustment
The pan adjustment of a PLFRESNEL1 LED Luminaire is achieved by loosening the yoke bolt of the securing clamp
attached to the luminaire's yoke assembly. Loosen the bolt, set the luminaire to the desired position and retighten.
Tilt Adjustment
PLFRESNEL1 LED Luminaires offer variable tilt settings. The unit can be set at a specific angle (in relation to its
mounting position) or at an angle between 0 to 90 degrees. When the yoke is in the position shown in Figure 6, you
have full range access to shutters the gate etc. If you flip the yoke over some access is reduced but the over all volume
the luminaire takes up is reduced. This is particularly useful in tightly hung lighting positions or in theatres with low
grids.
Figure 6: Luminaire Tilt Adjustment
To adjust and set tilt angle of the luminaire:
Step 1. Mount luminaire in desired location (see "Mounting" on page 9 for more information).
Step 2. Loosen, but do not remove, T-Handle Tilt Lock at base of yoke assembly as shown in Figure 6.
Step 3. Position luminaire to desired tilt position.
Step 4. Retighten T-Handle Tilt Lock to set position.
Yoke Assembly
Cooling Vents (see note below)
T-Handle Tilt Lock
NOTE: To allow for proper cooling,
make sure luminaire head is
orientated as shown (with forward
cooling vents pointed upwards).
Safety Cable
Sliding Yoke Assembly
Safety Cable
Anchor Point.
SAFETY CABLE: FOR LUMINAIRE, the supplied safety cable is
recommended for all hanging installation and may be required by
national and local codes. Loop/attach safety cable to safety cable anchor
point (as shown) and attach to structure.
(supplied with
luminaire)

Beam Adjustments 11
PLFRESNEL1 LED Luminaires Installation & User’s Manual
BEAM ADJUSTMENTS
1. Beam Adjustments
To adjust the beam on the :
Step 1. As shown in Figure 7, loosen Beam Adjustment Knob
Step 2. Slide beam adjustment back (for spot) or forward (for flood) as desired.
Step 3. Hand-tighten Beam Adjustment Knob to lock position.
Figure 7: Zoom and Focus Adjustment Knobs
2. Barndoor Assembly
Philips Selecon offers as an optional accessory, a four-leaf barndoor assembly. This assembly is sold separately and
available from your Authorized Philips Selecon Authorized Dealer. For information on all available accessories for
the PLFRESNEL1 LED Luminaire, refer to "Accessories" on page 4.
Spot Flood
Beam Adjustment Knob

Installation & User’s Manual PLFRESNEL1 LED Luminaires
12 OPERATION AND PROGRAMMING
OPERATION AND PROGRAMMING
1. LCD Menu Operation
The PLFRESNEL1 LED Luminaire’s LCD Display and Menu System provides local control for accessing all the
fixture’s status information, menu options, and settings.
Note: If there are multiple luminaires in a system, changes would need to be made at each LCD Menu as desired.
Upon power up, the LCD will display the main screen showing the product type/name. If DMX is enabled, the
programmed address will appear after power up.
Figure 8: LCD Display and Menu System
Up/Down/Left/Right Arrow Buttons -
Navigates menu system and used for
Escape Button -
Enters menu options. Navigates
OK (Enter) Button -
Accesses details, activates
a field, or enters a setting
depending on the current menu item.
selecting and setting options.
(backs up) one menu level.
PRESET Button -
Allows the recall of
LCD Display -
Displays all menu parameters and
option settings. Also displays DMX512
address (DMX models only).
INTENSITY Button -
Allows the customization of current
intensity (light output). Note, using the
LEFT and RIGHT arrow buttons you can
select each RGBW channel individually
and change their intensity using the UP
and DOWN arrows.
stored presets.

LCD Menu System 13
PLFRESNEL1 LED Luminaires Installation & User’s Manual
2. LCD Menu System
The LCD Display Menu system consists of several categories. Use the four arrow buttons as required (refer to Figure
8 on page 12) to access and make changes to the menu items. When the desired menu item is reached, press [OK] to
display the menu options. Use navigation and [OK] buttons to view status and configure the LCD Menu as required.
Note: Depending on the security settings, certain menu items may be password protected. You must have the set
PassPIN in order to access these items. Locked items will have a "Key" icon displayed next to them.
To navigate and access menu settings/selections:
Step 1. At Main Menu, press [ESC] / [MENU] button once. A small window will appear over Main Menu with sub-
menu categories:
a. Save as Preset
b. Edit a Preset
c. Color Mix
d. Fan Control
e. Settings
f. Lock Fixture
g. Enter Password
h. LED Status
Step 2. Press [OK] at desired menu item to access and make changes.
Step 3. Make changes as desired.
Note: For complete menu structure and available options, see "Menu Structure (continued)" on page 15.
Note: When DMX512 signal is present, Edit Preset and Color Mix options will not appear in menu structure.
To navigate fixture status menus:
Step 1. At Main Menu, press LEFT or RIGHT arrow button once. Main menu screen will change to fixture status
screen will appear as follows (note, depending on which arrow button is pressed, status screens may appear
in reverse order):
a. DMX Address (note, if fixture is UNLOCKED, hit [OK] to change DMX address)
b. Fixture Hours (displays fixture operating hours since last reset)
c. Fixture Power (displays Max Power Limit setting (in Watts), Present Power consumed by fixture (in
Watts), and Hours of Use)
d. Fixture Status (displays current operational temperature, LED status, and fan speed setting)
Step 2. Press LEFT or RIGHT arrow buttons to scroll through status screens.
Step 3. Press [ESC] at anytime to access menu settings. See "To navigate and access menu settings/selections:" on
page 13.

Installation & User’s Manual PLFRESNEL1 LED Luminaires
14 OPERATION AND PROGRAMMING
Menu Structure
Note: See "To navigate and access menu settings/selections:" on page 13 to learn how to access menus. To save
changes, hit [OK]. Press [ESC] to cancel any changes you made.
MAIN MENU
Save as Preset
Sub Menu Options Comments
Select Preset to Save - (Option)
Scrolls and sets current user-defined
color mix to various recallable presets
in the fixture using arrow buttons.
Note: To edit a current (set) preset,
see Edit Presets.
Off Users can:
• Save the current settings (look) to
a specific recallable Preset in the
fixture’s memory.
• Edit the levels (values) for Red,
Green, Blue, White, and Intensity
values (in percent%) by using the
arrow buttons. Once the values
are adjusted, the preset is saved
as desired.
*Only intensities may be stored on
White Color Temperature presets.
RGBW in these presets cannot be
edited or changed.
Scratch Pad
Warm White*
Cool White*
Day Light*
Preset X (5 through 31)
Continued next page
LCD Display /
Menu System

LCD Menu System 15
PLFRESNEL1 LED Luminaires Installation & User’s Manual
Menu Structure (continued)
Edit a Preset
Sub Menu Options Comments
Select Preset to Edit - (Option)
Selects a current preset and outputs
the preset, so preset can be edited.
Note: To save a specific look of the
fixture, see Save Presets.
Off Users can:
• Edit the current settings (look) to a
specific recallable Preset in the fix-
ture’s memory.
• Edit the values for Red, Green,
Blue, White, and Intensity values
(in percent%) by using the arrow
buttons.
• Once the values are adjusted, the
"Save Preset" menu option
appears to save the edits.
NOTES:
*Only intensities may be stored on
White Color Temperature presets.
RGBW in these presets cannot be
edited or changed.
**If a Calibrated Preset's Color Mix is
changed (5 thru 25), an asterisk '*' is
appended to the end of the name to
indicate that it has been modified.
This only happens if the name
matches the original calibrated name,
stored in EEPROM. This does not
happen if the Intensity is changed,
only the color mix.
Scratch Pad
Warm White*
Cool White*
Day Light*
Preset X (5 through 31)**
Note: When DMX512 signal is present, Edit a Preset option will not appear in menu structure.
Color Mix
Sub Menu Options Comments
Select Color or Intensity to Adjust -
(Option)
Red
Users can:
• Edit Red, Green, Blue, White, and
Intensity values (in percent%) by
using the arrow buttons.
• Once the values are adjusted,
press [OK] to save the edits.
Green
Blue
White
Intensity
Note: When DMX512 signal is present, Color Mix option will not appear in menu structure.
Continued next page
Continued from previous page
Fan Control
Sub Menu Options Comments
Select and Set Fan Speed - (Option)
Note, hit Cancel to cancel any
changes you made.
Max Highlight "Max" button and hit [OK] button on menu. Sets the maximum
speed of the fan.
Level
Level sets the fan toa constant speed
(will not vary). Adjust level (on fan
speed level bar) using Left and Right
arrow buttons, highlight "Level" button
in menu, and hit [OK] on menu to use
user-defined level.

Installation & User’s Manual PLFRESNEL1 LED Luminaires
16 OPERATION AND PROGRAMMING
Menu Structure (continued)
3. Security
Unwanted changes to the Fixture's Configuration or Setting can be controlled by setting a security level, or Locking
the Fixture. Three levels of security are available in addition to completely Locking the Fixture.
PLFRESNEL1 LED Luminaires are shipped with default passwords. Users may set their own password (four-digit
number). When setting a password, write it down and keep it in a secure location. Note, Philips Selecon does not have
records of passwords established by users or owners.
Note: Contact Philips Selecon technical support if a unit is locked and the password is lost for instructions on how to
reset luminaire.
Note: If the Fixture is locked when it is powered down the fixture will remain in the locked state when powered up.
Passwords
Establishing or Changing Passwords
Step 1. At a Status Screen, press [MENU] and scroll to "Settings", press [OK].
Step 2. Go to the Security section.
Continued from previous page
Settings
Sub Menu Options Comments
SETTINGS - (Option)
Scrolls and sets the various fixture
settings using arrow buttons.
See "Settings" on page 18 for details.
Lock Fixture
Sub Menu Options Comments
LOCK - Are you sure? Yes (to Lock Fixture) / No
Use arrow buttons to make selection.
Press [OK] to accept. Note, a
password must be established (set) in
order to lock a fixture. Locking the
fixture will disable access to changing
menu settings.
LED Status
Sub Menu Options Comments
LED Status Information
Scrolls through the various levels
using arrow buttons as indicated on
menu screen. Depending on the
arrow button pressed, the screens
may appear in a different order that
shown in "Options".
LED 1
Displays LED’s current status (in
percentage%) of Intensity, Red,
Green, Blue, and White elements of
the LED). Also displays current color
temperature (i.e., WARM WHITE),
Fan Speed, operational LED junction
temperature, power settings.
Levels Displays DMX levels for each LED element (Red, Green, Blue, and
White) and total power.
Enter Password
Sub Menu Options Comments
Enter Pass PIN Enter four-digit password For details, refer to "Security" on
page 16.

Presets 17
PLFRESNEL1 LED Luminaires Installation & User’s Manual
Step 3. Select a Level to change ( Level 1 PIN / Level 2 PIN / Level 3 PIN).
Step 4. Press [OK] to edit using the [UP ARROW], [DOWN ARROW], [LEFT ARROW] or [RIGHT ARROW]
keys to enter a four-digit password (using 0 to 9).
Step 5. Press [OK] to save changes. If you hit [ESC] (Escape) password will not be stored and process must be
repeated.
Step 6. Password is set.
Note: The current security level is displayed next to the Security heading. Only Passwords at, or below, that level
will be displayed for modification. The level can be changed by entering a higher level Password on the "Enter
PassPIN line directly below the Security heading, like Step 4 above.
Security Levels
Locking Fixture
To lock the fixture:
Step 1. At a Status Screen, press [MENU] and scroll to "Lock Fixture".
Step 2. Press [OK].
Step 3. Use [LEFT ARROW] or [RIGHT ARROW] keys to highlight "YES" ", press [OK].
Step 4. Fixture is now locked.
Note: When the Fixture is Locked only the [ESC]/[MENU] key is functional. Pressing this key will display a request
for a password. When a valid password is entered the fixture is unlocked to the security level of the entered password.
4. Presets
Presets are Color Mixes that are stored in the Fixture, they can be recalled to reproduce a specific output from the
fixture. Presets are made up of a Color Mix; Red, Green, Blue, and White. They also have Intensity associated with
them.
Presets can be recalled via the User interface or by a DMX channel, when under DMX control. The Preset’s Intensity
is applied if the User Interface is used; if DMX, the DMX Intensity channel is used for Intensity.
Presets Types
Presets are classified as Locked, Protected, or User. The type of preset determines what aspects of the Preset can be
modified.
Locked
Locked Presets are factory Calibrated, and their Color Mix cannot be changed by the user. Their Intensity can be
changed. Three Presets (2-4), "Warm White', "Cool White", and "Day Light", are Locked.
Security Level Description Default PassPIN
0System is locked; the only key that is active is the Menu/ESC Key. When this key is pressed a
PassPIN is requested. Not Applicable
1All keys are Active.
You can select any Preset, and change Intensity, set DMX Address. 1111
2 Editing and Saving of Presets is added to Level 1 functionality. 2222
3 Operationally the same as level 2, however all settings are available on the Settings screen. 3333

Installation & User’s Manual PLFRESNEL1 LED Luminaires
18 OPERATION AND PROGRAMMING
Preset 0, the "off" preset is also Locked to the OFF value.
Protected
Protected Presets are also Factory Calibrated, and by default are Protected from changes to their Color Mix. Their
Intensity can be changed. Protected Presets are Presets 5-25. They can be Un-Protected by setting "Protected" to
"No"; see section on Settings. If Un-Protected these presets function like User Presets.
The Factory Calibrated values for the protected presets can be re-loaded to the original factory calibration settings by
setting "Load Factory" to "Yes" "; see section on Settings.
User
User Presets can have their Color Mix and Intensity changed without restriction.
Note: If the Color Mix of a Factory Calibrated Preset is changed, by turning protection Off, an '*' is appended to the
end of the Preset's Name to indicate that the Calibrated values have been changed.
Editing Preset Names
On the Edit Preset screen, the option is available to edit the name of a preset, via Screen button. However, the names
of Presets 0-4 cannot be edited.
Use the [LEFT ARROW] and [RIGHT ARROW] keys to select the character to be changed and use the [UP
ARROW] and [DOWN ARROW] keys to change that character. The Character Scroll order is A-Z, space, 0-9. If you
are scrolling up the Alpha character displays as Upper Case; if you are scrolling down the Alpha character displays as
Lower Case. Stop on the character you want, ignoring case, then press the opposite [UP ARROW] or [DOWN
ARROW] key if you want to change the case. [OK] to save changes, [ESC] to cancel changes.
5. Settings
The following Parameters can be changed on the Settings Screen.
The first column "Security Level" is the minimum security level you have to be at before the line is displayed for
editing in the Settings screen.
To edit a value on the Setting Screen, use the [UP ARROW] or [DOWN ARROW] keys to move the highlight to the
settings value you wish to change. Press [OK] to begin editing that value. Use the [UP ARROW], [DOWN
ARROW], [LEFT ARROW] or [RIGHT ARROW] keys to make changes to the value. Press [OK] when complete to
save changes, or [ESC] to cancel changes to that value.
When done making changes on the Settings Screen press [ESC] to re-boot fixture and implement changes. Fixture
will not re-boot if nothing was changed.
Security Level Parameter Values Default Description
Security
1Enter
PassPIN 4-Digits (0 to 9) **** There are 4 levels of security, this allows
you to change the level while in the
Settings Screen.
3 Level 1 PIN 4-Digits (0 to 9) 1111 Sets Level 1 PassPIN
3 Level 2 PIN 4-Digits (0 to 9) 2222 Sets Level 2 PassPIN
3 Level 3 PIN 4-Digits (0 to 9) 3333 Sets Level 3 PassPIN
3 Power-Up 1 - 3 or Locked 3 Security Level after Power-Up, if not
Locked (Level 0)