Philips Showline SL eSTROBE 130 User manual

SL eSTROBE 130 LED Luminaire
Sh wline

SL eSTROBE 130 User’s Manual
www.Philips.com/Showline
24-004-3590-00 Rev1.0
SL eSTROBE 130 LED Luminaire installation & User’s Manual
2013 Philips Group. All rights reserved.
The material in this manual is for information purposes only and is subject to change without notice. Showline
assumes no responsibility for any errors or omissions which may appear in this manual. For comments and
suggestions regarding corrections and/or updates to this manual, please visit the Showline website at
or contact your nearest Showline office. www.philips.com/showline
Note: Information contained in this document may not be duplicated in full or in part by any person without prior written
approval of Showline. Its sole purpose is to provide the user with conceptual information on the equipment mentioned. The use of
this document for all other purposes is specifically prohibited.

Installation & User’s Manual
SL eSTROBE 130 LED Luminaire
Additional Resources for DMX512
For more information on installing DMX512 control systems, the following publication is available for purchase
from the United States Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guide
for Users and Installers, 2nd edition" (ISBN: 9780955703522). USITT Contact Information:
USITT
315 South Crouse Avenue, Suite 200
Syracuse, NY 13210-1844
Phone: [phone] or 1.315.463.6463
www.usitt.org
Showline Limited Two-Year Warranty
Showline offers a two-year limited warranty of its luminaires against defects in materials or workmanship from the
date of delivery. A copy of Showline two-year limited warranty containing specific terms and conditions can be
obtained by contacting your local Showline office.
Warnings and Notices
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
Do not use outdoors.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations and at heights where it will not readily be subject
to tampering by unauthorized personnel.
The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
Do not use this equipment for other than intended use.
Refer service to qualified personnel.
WARNING: You must have access to a mains circuit breaker or other power disconnect device
before installing any wiring. BE sure that power is disconnected by removing fuses or turning the
mains circuit breaker off before installation. Installing the device with power on may expose you
to dangerous voltages and damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code and local codes for cable specifications.
Failure to use proper cable can result in damage to equipment or danger to personnel.
WARNING: This equipment is intended for installation in accordance with the Nation Electric
Code and local regulations. It is also intended for installation in indoor applications only. Before
any electrical work is performed, disconnect power at the circuit breaker or remove the fuse to
avoid shock or damage to the control. It is recommended that a qualified electrician perform this
installation.

TABLE OF CONTENTS
Showline Offices Inside Front Cover
IMPORTANT INFORMATION
Warnings and Notices
Additional Resources for DMX512
Showline Limited Two-Year Warranty
TABLE OF CONTENTS
PREFACE
About this Manual
Included Items
SL eSTROBE 130 LED LUMINAIRE OVERVIEW
SL eSTROBE 130 LED Luminaire Components
Common Luminaire Components
LCD Display / Menu System
INSTALLATION AND SET UP
Power Requirements
Connecting Power
Floor Mounting
Truss Mounting
SL eSTROBE 130 LED Luminaire
Connecting to the DMX512 Network
Mounting Luminaire
OPERATION AND PROGRAMMING
LCD Display and Menu System
LCD Display and Menu System Operation
SL eSTROBE 130 LED Luminaire Menu Tree
Dimming Curve Selection
Master / Slave Operational Mode
DMX CONTROL
RDM PARAMETER IDs
Single Channel Mode
Three Channel Mode
Four Channel Mode
16-Bit Mode
Zone Mapping Mode
Strobe Rate
Strobe During
SL eSTROBE 130 LED Luminaire DMX Mapping
SL eSTROBE 130 LED Luminaire RDM Parameter IDs
CLEANING AND CARE
Special Cleaning and Care Instructions
Front Lens Cleaning
Service and Maintenance
Accessories
TECHNICAL SPECIFICATIONS
Operational Specifications
Luminaire Dimensions
Table of contents
Installation & User’s Manual SL eSTROBE 130 LED Luminaire
2
1
1
1
3
3
4
5
4
6
6
7
7
6
7
8
8
8
10
11
12
13
13
14
15
16
17
23
13
28
31
31
31
32
33
34

PREFACE
1. About this Manual
The document provides installation and operation instructions for the following products:
Please read all instructions before installing or using this product. Retain this manual for future reference.
Additional product information and descriptions may be found on the product specification sheet.
Note: The SL eSTROBE 130 LED Luminaire is universal voltage 100 to 240 VAC (auto-ranging).
2. Included Items
Each SL eSTROBE 130 LED Luminaire includes the following items:
SL eSTROBE 130 LED Luminaire
SL 130 LED LuminaireeSTROBE
Installation and User’s Manual (this document)
3
About this Manual
AC Power Input Cable
Installation & User’s Manual
SL eSTROBE 130 LED Luminaire

SL eSTROBE 130 LED Luminaire Overview
4
SL eSTROBE 130 LED Luminaire Overview
1. SL eSTROBE 130 LED Luminaire Components
Common Luminaire Components
Figure 1: SL eSTROBE 130 LED Luminaire Components
Front of Unit Rear of Unit
DMX512-A /
LCD Display /
High Intensity LED Array
Yoke Assembly
DMX512-A /
Accessory Holder
Yoke (Tilt) Position
Locking Handle
Truss Hook / Clamp
Attachment Point
Accessory Holder Clip
RDM Input RDM THRU
Menu System AC Power Input
Installation & User’s Manual SL eSTROBE 130 LED Luminaire

5
LCD Display/Menu System
LCD Display / Menu System
Note: For Menu operation and programming details, refer to the "LCD Display and Menu System” on page 8.
Figure 2: LCD Display & Menu System
LEFT Arrow Button RIGHT Arrow Button
ENTER(OK) Button
EXIT Button
LCD Display
Installation & User’s Manual
SL eSTROBE 130 LED Luminaire

Installation and Set up
6
INSTALLATION AND SET UP
1. Power Requirements
The SL eSTROBE 130 LED Luminaire operates on AC input voltages from 100 to 240 VAC.
WARNING! This luminaire does not contain an ON/OFF switch. Always disconnect power input cable to completely
remove power from the luminaire when not in use.
AC Power Operation
When connected to an AC source, the luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The
luminaire contains an auto-ranging power supply. Each luminaire can draw up to 130 Watts.
Table 1: SL eSTROBE 130Voltage (VAC) vs. Current
2. Connecting Power
Direct connection to a AC power source using an AC input cable.
Voltage (AC)Total Current (A)Voltage (AC)Total Current (A)
0.54
0.56
0.59
0.62
0.65
0.68
0.72
240
3. Connecting to the DMX 512 Network
Basic DMX512 installation consists of connecting multiple SL eSTROBE 130 LED Luminaires together (up to 32
luminaires) the control console (or DMX512 control source) to the DMX in "daisy-chain" fashion. A cable runs from
connector on the connector on first SL eSTROBE 130 LED Luminaire. Another cable runs from the other DMX
on the next SL eSTROBE 130 LED Luminaire (or DMX512 the first Luminaire to a DMX connector device to be controlled).
Luminaire
Rear of Unit
DMX512-A / RDM DMX512-A / RDM
Input Connector THRU Connector
Figure 3: SL eSTROBE 130 LED Luminaire DMX512 Input / THRU Connections
Installation & User’s Manual SL eSTROBE 130 LED Luminaire
100 180
1.30
110 1901.18
160 0.81
150 230
0.86
140 220
0.92
130 210
1.00
120 200
1.08
170 0.76

Mounting Luminaire 7
Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on
page 1. For SL eSTROBE 130 LED Luminaire DMX Mapping, refer to "DMX CONTROL" on page 13.
Figure 4: SL eSTROBE 130 LED Luminaire - DMX512 Connections
DMX512 (out to the next luminaire or
DMX512 controlled device)
DMX512
DMX512 (out from first
to second luminaire)
DMX512 Connections
Note: Remaining pins on each connector are not used.
DMX512 Signal XLR Pin
Common (Drain) 1
DMX512 - 2
DMX512 + 3
(from console or
control device)
4. Mounting Luminaire
Floor Mounting
The SL eSTROBE 130 LED Luminaire is designed to sit directly on its yoke assembly in a floor installation application.
When used in this type of application, loosen the locking handle securing the inner portion of the yoke assembly and
separate out Figure 5). Be sure to leave enough space around the luminaire to allow proper,
uninterrupted airflow for cooling.
(as shown in
Figure 5: Floor Mounting
Figure 6: Truss Mounting
Yoke Assembly
Inner Portion (Stand)
of Yoke Assembly
Installation & User’s Manual
SL eSTROBE 130 LED Luminaire
Truss / Hanging Applications
The SL eSTROBE 130 LED Luminaire is provided with the ability to hang via truss hooks, clamps, etc. (soldseparately).
Simply attach hook, clamp, etc. to the SL eSTROBE 130 LED Luminaire enclosure assembly in the provided M10
holes. It is recommended (and may be required by local and national safety codes) to use and install a safety cable
(sold separately) as illustrated in Figure 6. When hanging the fixture, be sure to leave enough space around the luminaire
to allow proper, uninterrupted airflow for cooling and positioning. Refer to for"Luminaire Dimensions" on page 34
spacing (dimensional) requirements.

OPERATION AND PROGRAMMING
8
Figure 7: LCD Display and Menu System
OPERATION AND PROGRAMMING
1. LCD Display and Menu System
SL eSTROBE 130 LED Luminaires
The SL eSTROBE 130 LED Luminaire’s LCD Display and Menu System provides local control for accessing the
following fixture’s settings:
Presets (Standard and User Defined)
Chase
Settings
Status
Note: If there are multiple luminaires in a system, changes would need to be made at each LCD Menu as desired. For
the SL eSTROBE 130 LED Luminaire menu structure, see "SL eSTROBE 130 LED Luminaire Menu Tree" on page 10.
LEFT Arrow Button RIGHT Arrow Button
ENTER Button
EXIT Button
LCD Display
2. LCD Display and Menu System Operation
To navigate and access the menu settings/selections:
Step 1.Make sure the luminaire is powered and turned on.
Step 2.Press the desired button to access the menu categories.
Step 3. Use the “ ” and “ ” arrow buttons to navigate through the various options and settings.
Step 4.Make changes as desired.
Press the OK button to accept changes.
Upon power up, the LCD will display the main screen display menu of SL eSTROBE 130 LED Luminaire.
Press “ ” or “ ” to select then press 'OK' to enter.
The LCD Display Menu system consists of several categories. Upon power up, the LCD will display the main menu
automatically. desired menu item is reached, press the OK button to display the menu options, and to navigate When the
and configure the menu options as required.
Installation & User’s Manual SL eSTROBE 130 LED Luminaire

LCD Display and Menu System Operation 9
Press the OK button to access the Preset menu.
Select Chase and press the OK button to access.
Use the LEFT and RIGHT arrow buttons to scroll through all presets
and select the desired preset number.
Use the LEFT and RIGHT arrow buttons to scroll through all menus.
Once at the desired preset, use theLEFT and RIGHT arrow buttons to
adjust parameter value as desired. Once all values are adjusted as
desired, press the OK button.
Press the
display “Save Preset: x”. Use the LEFT and RIGHT arrow
buttons to make a selection, then press the OK button.
ESC button to select Save a Preset, the screen will then
Once at desired menu, use the LEFT and RIGHT arrow buttons to
adjust the parameter value as desired. Once all values are adjusted as
desired, press the OK button.
Press the OK button to select the desired menu. In RGB
mode, the user can select Intensity, Strobe Rate, Duration,
Effects, Zone1, Zone2, Zone3 and Zone4.
Select the Built-in Chase X(1-10) option or ,
then press the OK button to select the desired menu.
the User Chase(1-8) option
Preset
Chase
Main Menu
1. Preset
. Chase
1. Chase Select
Step 5. The preset is now saved. Press the ESC button to exit the current menu.
Step 5. The chase is now saved. Press the ESC button to exit the current menu.
Step 5.
Installation & User’s Manual
SL eSTROBE 130 LED Luminaire
Press CHECK MARK(OK)button to access Status.
Press the OK button to access Settings.
Use the LEFT and RIGHT arrow buttons to scroll through all menus.
Use the LEFT and RIGHT arrow buttons to scroll through all menus.
Once at the desired menu, use the LEFT and RIGHT arrow buttons to
check the related fixture information.
Once at desired menu, use LEFT and RIGHT arrow buttons to
adjust the related fixture information. Once all values are adjusted
as desired, press CHECK MARK (OK)button.
Press the OK button to select the desired menu
from LED Level, Temperature, and Other Info.
Press the OK button to select the desired menu
among General, Factory Default, DMX and Display.
Status
Settings
Note: For more information about Preset, Color Filter, Chase, Strobe/Timing, Settings and Status, please
refer to the “SL eSTROBE 130 LED Luminaire Menu Tree” on page 11.
To check the fixture operational status:
.Settings
1. General
.Status
1. LED Level
Step 5. Adjustment is now saved. Press ESC button to exit current menu.
To edit and save a preset

SL eSTROBE 130 LED Luminaire Menu Tree
3. SL eSTROBE 130 LED Luminaire Menu Tree
Figure 8: SL eSTROBE 130 LED Luminaire Menu Tree
10
Installation & User’s Manual SL eSTROBE 130 LED Luminaire

Dimming Curve Selection
Figure 9: SL eSTROBE 130 LED Luminaire Dimmer Curves
11
Installation & User’s Manual
SL eSTROBE 130 LED Luminaire
4. Dimming Curve Selection
Through the menu, you are able to select one of four dimming curves:
Linear Curve
Linear Curve
PL_Curve
PL_Curve
S_Curve
S_Curve
Square Curve
DMX Value DMX Value
*PL Curve follows the dimming curve of Philips Selecon PL
series LED luminaires.
DMX Value DMX Value
Square Curve
Lumen OutputLumen Output Lumen OutputLumen Output

Master / Slave Operational Mode
The Master / Slave Operational Mode allows one SL eSTROBE 130 LED Luminaire to act as the “Master” luminaire
and luminaire luminaire. luminaire
luminaire and follow any commands send from a “Master” luminaire. Only one
“Master” luminaire is allowed in this type of operation.
all other connected s are controlled by this master When a is set to
“Slave” mode, it will only
Note: For more information on DMX512 networking and systems, refer to “Additional Resources for DMX512”
on page 1. For SL eSTROBE 130 LED Luminaire DMX Mapping, refer to on page “DMX CONTROL” 13.
Figure 10: SL eSTROBE 130 LED Luminaire - Master / Slave Configuration
5
Slave LuminaireSlave LuminaireMaster Luminaire
12
Installation & User’s Manual SL eSTROBE 130 LED Luminaire
Set the first in the DMX512 chain to Master Mode through the ’s menu system.luminaire luminaire
Set all other connected luminaires to Slave Mode.
The master luminaire can be controlled via DMX512, RDM or through standalone operation(a self
-contained network utilizing on-board effects). The salve luminaires will mimic the master luminaire’s
operation in all cases.
Step 1.
Step 2.
Step 3.
To setup a master / slave network:

DMX Control
1. SL eSTROBE 130 LED Luminaire DMX Mapping
Table 2: SL eSTROBE 130 LED Luminaire DMX Channel Mapping (Single Channel Mode)
Table 3: SL eSTROBE 130 LED Luminaire DMX Channel Mapping (Three Channel Mode)
Table 2 provides DMX channel mapping of all DMX512 control values when the SL eSTROBE 130
LED Luminaire is in Single Channel mode (as set by the luminaire’s menu system).
Table 3 provides DMX channel mapping of all DMX512 control values when the SL eSTROBE 130
LED Luminaire is in Three Channel mode (as set by the luminaire’s menu system).
Note: These tables assume a DMX start address of 1. When a different starting address is used, this address
becomes channel 1 function and other functions follow in sequence.
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 255
0 - 255
0 - 255
0 - 255
1
1
2
3
0
0
0
0
Please refer to the Strobe Rate detail.
8 bit control for Intensity of LED settings
Strobe’s duration, Range is 0-255
Strobe rate slow to fast.
White light mode ( when strobe rate is also at 255)
White light mode ( when strobe duration is also at 255)
Please refer to the Strobe Duration Detail
Please refer to the Strobe Rate Detail.
Single Channel Mode
Three Channel Mode
This section contains information for operating the luminaire using DMX control in Single Channel, Three
Channel, Four Channel, 16-Bit Control or Zone Mapping modes. For Menu options and detailed information,
“LCD Display and Menu System” on Page 8.see the
Strobe Rate
Intensity
Strobe Duration
Strobe Rate
13
Installation & User’s Manual
SL eSTROBE 130 LED Luminaire
DMX
Channel
DMX
Channel
Parameter
Parameter
Range DMX
Range DMX
Range%
Range%
Description
Description
Default- recommended
console default values
Default- recommended
console default values

DMX Control
14
Installation & User’s Manual SL eSTROBE 130 LED Luminaire
Table 4: SL eSTROBE 130 LED Luminaire DMX Channel Mapping (Four Channel Mode)
Table 4 provides DMX channel mapping of all DMX512 control values when the SL eSTROBE 130
LED Luminaire is in Four Channel mode (as set by the luminaire’s menu system).
Four Channel Mode
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 255
0 - 255
0 - 255
0 - 255
1
2
3
4
0
0
0
0
8 bit control for Intensity of LED settings
Strobe’s duration, Range is 0-255
Strobe rate slow to fast.
White light mode ( when strobe rate is also at 255)
White light mode ( when strobe duration is also at 255)
No Effect = DMX 0-5
= DMX 215-235
= DMX 187-214
= DMX 185-186
= DMX 183-184
= DMX 180-182
= DMX 176-179
= DMX 174-175
= DMX 172-173
= DMX 129-171
= DMX 86-128
= DMX 43-85
= DMX 6-42
= DMX 236-255
Circle zone chase clockwise
Random zones
Checker pattern B
Checker pattern A
Ring 4
Ring 3
Ring 2
Ring 1
Random
Ramp Up/Down
Ramp Down
Ramp Up
Circle zone chase counter-clockwise
Controls strobe operations as follows:
Please refer to the Strobe Duration Detail
Please refer to the Strobe Rate Detail.
Intensity
Strobe Duration
Strobe Rate
Effects
DMX
Channel Parameter Range DMX Range% Description
Default- recommended
console default values

16-Bit Mode 15
Installation & User’s Manual
SL eSTROBE 130 LED Luminaire
Table 5: SL eSTROBE 130 LED Luminaire DMX Channel Mapping (16-Bit Mode)
Table 5 provides DMX channel mapping of all DMX512 control values when the SL eSTROBE 130
LED Luminaire is in 16-Bit mode (as set by the luminaire’s menu system).
16-Bit Mode
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 65535
0 - 255
0 - 255
0 - 255
0 - 255
1
4
6
5
2
3
0
0
0
0
DMX 0
16 bit control for Intensity of LED settings
Strobe’s duration, Range is 0-255
Strobe rate slow to fast.
White light mode ( when strobe rate is also at 255)
White light mode ( when strobe duration is also at 255)
No Effect = DMX 0-5
= DMX 215-235
= DMX 187-214
= DMX 185-186
= DMX 183-184
= DMX 180-182
= DMX 176-179
= DMX 174-175
= DMX 172-173
= DMX 129-171
= DMX 86-128
= DMX 43-85
= DMX 6-42
= DMX 236-255
Circle zone chase clockwise
Random zones
Checker pattern B
Checker pattern A
Ring 4
Ring 3
Ring 2
Ring 1
Random
Ramp Up/Down
Ramp Down
Ramp Up
Circle zone chase counter-clockwise
Controls strobe operations as follows:
Please refer to the Strobe Duration Detail
Please refer to the Control Channel detail.
Please refer to the Strobe Rate Detail.
Intensity High
Intensity Low
Control Channel
Strobe Rate
Strobe Duration
Effects
DMX
Channel Parameter Range DMX Range% Description
Default- recommended
console default values

Zone Mapping
Table 6: SL eSTROBE 130 LED Luminaire DMX Channel Mapping (Zone Mapping Mode)
Table 6 provides DMX channel mapping of all DMX512 control values when the SL eSTROBE 130
LED Luminaire is in Zone Mapping mode (as set by the luminaire’s menu system).
Zone Mapping Mode
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 65535
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
16 bit control for Intensity of LED settings.
Effects.( Refer to the Effects detail)
8-bit control for zone Intensity.
8-bit control for zone Intensity.
8-bit control for zone Intensity.
8-bit control for zone Intensity.
Strobe’s duration(Refer to the Strobe Duration Detail.)
Strobe’s duration(Refer to the Strobe Duration Detail.)
Strobe’s duration(Refer to the Strobe Duration Detail.)
Strobe’s duration(Refer to the Strobe Duration Detail.)
Strobe’s rate slow to fast.(Refer to the Strobe Rate detail)
Strobe’s rate slow to fast.(Refer to the Strobe Rate detail)
Strobe’s rate slow to fast.(Refer to the Strobe Rate detail)
Strobe’s rate slow to fast.(Refer to the Strobe Rate detail)
Control Channel(Refer to the Control Channel detail)
16
Installation & User’s Manual SL eSTROBE 130 LED Luminaire
DMX
Channel Parameter Range DMX Range% Description
Default
Effects
Control Channel
Zone 1 Intensity
Zone 2 Intensity
Zone 3 Intensity
Zone 4 Intensity
Zone 1 Strobe Duration
Zone 2 Strobe Duration
Zone 3 Strobe Duration
Zone 4 Strobe Duration
Zone 1 Strobe Rate
Zone 2 Strobe Rate
Zone 3 Strobe Rate
Zone 4 Strobe Rate
Master Intensity - Low
Master Intensity - High

0 0
43 17
42
41 16
40
39
38 15
37
36 14
35
34
33 13
32
31 12
30
29
28 11
27
26
25 10
24
23 9
22
21
20 8
19
18 7
17
16
15 6
14
13 5
12
11
10 4
9
8 3
7
6
5 2
0.500
0.586
0.581
0.581
0.575
0.575
0.570
0.570
0.565
0.565
0.559
0.559
0.559
0.554
0.554
0.549
0.549
0.544
0.544
0.540
0.540
0.535
0.535
0.530
0.530
0.526
0.526
0.521
0.521
0.517
0.517
0.512
0.512
0.508
0.508
0.504
0.504
0.500
0.586
4
3 1
2
1
44
DMX Value Percent(%) Frequency(Hz)
DMX 0-5 – No Flash
(single flash with
value>5 on intensity
one time
Table 7: SL eSTROBE 130 LED Luminaire Strobe Rate
Table 7 provides Strobe Rate values of SL eSTROBE 130 LED Luminaire.
Strobe Rate
Strobe Rate 17
Installation & User’s Manual
SL eSTROBE 130 LED Luminaire

45
18
88
35
87
86
34
85
84
83
33
82
81
32
80
79
78
31
77
76 30
75
74
73
29
72
71
70
28
69
68
27
67
66
65
26
64
63
25
62
61
60
24
59
58
23
57
56
55
22
54
53
21
52
51
50
20 0.610
0.592
0.735
0.735
0.735
0.726
0.726
0.717
0.717
0.709
0.709
0.701
0.701
0.693
0.693
0.685
0.685
0.678
0.678
0.670
0.670
0.663
0.663
0.656
0.656
0.649
0.649
0.642
0.642
0.635
0.635
0.635
0.629
0.629
0.622
0.622
0.604
0.604
0.616
0.598
0.616
0.598
0.610
0.592
0.744
49
48 19
47
46
89
DMX Value Percent(%) Frequency(Hz)
Table 7: SL eSTROBE 130 LED Luminaire Strobe Rate
SL eSTROBE 130 LED Luminaire Strobe Rate
18
Installation & User’s Manual SL eSTROBE 130 LED Luminaire