Philips Selecon User manual

CDM Version 1: NOV 2011 © 2011 Philips Selecon All Rights Reserved
LAMPING UP
20W CDM -Tm Philips Mini Master lamp - PGJ5 base
35W CDM -Tm Philips Mini Master lamp - PGJ5 base
The Philips Selecon Display Profile is supplied with the recommended lamp. Carefully read the manufacturers instructions for
safe lamp handling / use and disposal of used lamps. Replace with the recommended lamp only. Spares are available from
your Selecon dealer: www.seleconlight.com/distributors
To insert the lamp, push in the lid locking latch on the lamp housing and open the lid. Insert the lamp into the lamp base.
The Philips Selecon Display Profile has a built-in ballast to convert from your local voltage to the voltage required by the
lamp. Once you have installed the lamp your luminaire should be ready for use.
Recommendation to ‘Burn-In’ CDM-Tm Lamps
Due to colour shifts in new CDM-Tm lamps we recommend that these lamps are run continuously for a minimum „burn-in‟
period of 20hrs prior to final installation.
KEY OPERATING POINTS AND FEATURES
A: Pan lock.
B: Tilt lock.
C: Lamp lid latch.
D: Shutter lock.
E: Four beam masking shutters.
F: Pattern rotation / alignment.
G: Lens lid locking latch. Open this to insert
colour frames and accessories.
H: Colour frame and accessory holder.
I: Lens focus knobs.
J: Lens tube rotation lock.
K: Lamp socket.
L: Lamp peak / flat adjustment.
M: Pattern holder.
Philips Selecon Display Profile - CDM
**OPERATION MANUAL**
THIS INFORMATION IS DESIGNED TO PROVIDE YOU WITH THE INFORMATION
YOU NEED IMMEDIATELY UPON DELIVERY OF YOUR NEW LUMINAIRE.
If you require further assistance please contact your Philips Selecon dealer. www.seleconlight.com/distributors
WARRANTY REGISTRATION: www.seleconlight.com/warrantyreg
Take full advantage of the Philips Selecon service commitment and register all
your new luminaires quickly and easily online for full after-sales support.

CDM Version 1: NOV 2011 © 2011 Philips Selecon All Rights Reserved
ACCESSORIES
Colour frame for plastic filter
Linear glass diffuser
Medium diffusion glass
UV glass filter
Glass colour filter - primary blue, green, red and
yellow
Glass dichroic colour filter
PATTERN USE
Pattern size: E
Outside diameter: 37.5mm
Image area: 28mm
Tips to achieve the best results:
Always use black matt finish patterns as these reduce internal light reflections.
For custom / text logos please ensure the design is inside the 28mm diameter area.
The Philips Selecon Display Profile is supplied with an internal pattern holder. To fit your
pattern, remove the internal pattern holder from its magnetic mounting plate. Unclip the
locking plate and insert the pattern with correct orientation. Re-clip the locking plate and place
the pattern holder back on the magnetic mounting plate. Align using the Gobo Rotation Knob
(F).
Mounting options include track adaptors, ceiling mount plate, suspension hook clamp.
For full details contact your Philips Selecon dealer: www.seleconlight.com/distributors
SAFETY AND MAINTENANCE
Keep your Philips Selecon Display Profile in top condition and performing at its best by cleaning it regularly with a soft cloth.
The above is the only maintenance task that can be safely carried out by non approved personnel.
Philips Selecon has manufactured this luminaire in accordance with recognised best practices to recommended international
safety standards. It is your responsibility to maintain this luminaire in good and safe working condition.
Repairs should only be carried out by suitably qualified persons. Do not operate the luminaire with damaged lamps or cable,
etc. Consult your Philips Selecon distributor for assistance. Only replace damaged parts with authorised SDP spare parts.
N.B. Luminaire electrical cable –your Philips Selecon Display Profile is fitted with special heat resistant flexible cable,
replace with genuine SDP spare part cable kit only –please refer to your Selecon distributor.
(Replacement cable kits are supplied complete with necessary terminal connectors).
ELECTRICAL INSTALLATION
WARNING!!!
Risk of fire and electric shock. This product is to be installed by a qualified electrician only. This luminaire employs a
grounded type receptacle and is not intended for connection to a two-wire, ungrounded source of supply.
When installing this luminaire use wire conductor colour codes as follows:
230V Brown - Phase, Live 120V Black - Phase, Live
Blue - Neutral, Return White - Neutral, Return
Green/Yellow - Earth Green - Earth
LIMITED WARRANTY
Philips Selecon (“Selecon”) warrants all Philips Selecon luminaires against defects in materials or workmanship. The term of
this warranty is three years; from the date of delivery, and is dependant on the following operating conditions:
FOR ARCHITECTURAL DISPLAY: the SDP luminaire is used as a display light and in conditions typically found in a
museum being 10 to 12 hours daily, 7 days per week.
For full details of the Philips Selecon Warranty, please refer to our website: www.seleconlight.com
Australian customers please refer to the Australia specific warranty card included with this product.
Manufacturer
Philips Selecon, 19-21 Kawana Street, Northcote, Auckland 0627, New Zealand
Ph: [phone], Fax: [phone]
www.seleconlight.com