Philips HP8550 User manual

ServiceManual
Philips Consumer Lifestyle
Published by Philips Consumer Lifestyle Printed in the Netherlands © Copyright reserved Subject to modification
Summer Glow
HP8550
08/02
PRODUCT INFORMATION
- This full-body tanning appliance is equipped with an
electromechanical timer connected to an electronic
watchdog that immediately switches off the appliance
in case the timer is defective. This watchdog consists of
a PCB attached to the rear of he timer housing and also
gives a signal when the last minute of the set time has
been reached.
- The UV lamps only burn in combination with the IR
(relax) lamps. When the UV lamps are on the IR lamps
burn at reduced intensity.
- This tanning appliance has also been fitted with a scent
unit. The scent granules required for this unit can be
ordered as service part (see parts list).
IMPORTANT
- Because of the brief high starting voltage, the appliance
should be connected to a circuit protected with a 16A fuse.
- HPA lamps only go on at a restart if they have cooled down
sufficiently.
- Never touch the HPA lamps with your fingers. If necessary,
clean the lamps with a cloth moistened with some alcohol.
- When a new HPA lamp is installed, this lamp may have
a different colour compared to the other lamp. This is
normal and will disappear after a short period of use.
- After repair, the glass filters should be free from fingerprints.
If necessary clean the filters with some alcohol.
- Never look directly into the light of an HPA lamp when it
is on without protective goggles.
- Insufficient cooling – for instance when the vents are
blocked or when the fan has broken down – will cause the
thermal safety cut-out to switch the appliance off. Once the
cause of overheating has been removed and the appliance
has cooled down sufficiently, it will switch automatically on
again.
- Let the appliance cool down for 15 minutes before folding
it back into transport position and storing it.
- Only move the appliance when it is in transport position,
i.e. when it is folded.
- If there are complaints about inadequate tanning, the
output of the lamps can be measured with a UV-X 36
meter. For the minimum values, see table under ‘Technical
information’.

HP8550
TECHNICAL INFORMATION
5. Stand
- The column of the stand has been mounted by means of
a hydraulic press and cannot be removed without causing
serious damage.
- As a result, the hinge housing cannot be disassembled
either.
- The legs have been mounted on the paw by means of a
hydraulic press and cannot be removed without causing
serious damage.
To replace the hinge housing assy:
- Undo the screws of the main grip.
- Take the main grip off stand.
- Remove the black plastic tube from the column.
- Slide the lamp housing together with the slider off the
column.
To replace the paw and the paw cap (L&R) and the wheels:
- Undo the screw on the inside of the paw.
- Unsnap the paw caps.
- The wheels are now accessible.
- Undo 4 screws in the point of rotation of the paw to detach
the paw.
To replace the sliding plug leg:
- To replace the sliding plug of the leg, the existing sliding
plug has to be smashed with the pointed end of a hammer;
otherwise it can’t be removed without damaging the leg.
A new sliding plug can simply be snapped onto the leg.
Always unplug the appliance before disassembly or repair!
1. Replacing lamps, fans and starters.
- Fold the appliance out into operating position.
- Remove 12 screws on the bottom of the lamp housing.
- Remove the upper part of the lamp housing
(the fans, starters and internal wiring are now accessible)
- Remove the screws of the mounting bridge
- Remove the reflector clamps.
- Remove the reflector.
You have to lift the mounting bridge to do so.
2. Replacing timer and lock grips.
- Remove the timer knob.
- Undo the 4 screws under the knobs.
- Remove the timer front.
- Undo 6 screws of the timer housing.
- Remove the front of the timer housing.
- Timer and lock grips are now accessible.
3. Replacing watchdog
- Start disassembling the appliance as described under 2.
- Undo the 4 remaining screws.
- Remove the back of the timer housing.
- The watchdog is now accessible.
4. Replacing seesaws (always replace both)
- Make sure the slider is in bottom position.
- Start disassembling the appliance as described under 2.
- Remove the lock grips.
- Remove spring. Be careful, for the spring is tensioned.
- Remove 2 shafts.
- Remove the seesaws.
DISASSEMBLY & REPAIR INSTRUCTION
- Input voltage : 230 V – 50 Hz.
- Input consumption : Approx. 2200 W
- Fuse : 16 A
- UVA source : 2 x Philips Cleo HPA SYNERGIE
- IR source : 2 x Philips type 15040R
- Starter : KAIDA KCCD-G400
- Timer : 45 min. (motor driven)
- Radiation area : 190 x 70 cm
- Output (min) UVX-36 meter : 0.2 W/cm² at 65 cm. straight below the distance indicator
- Protecting goggles : 2 x HB072
- Safety : Class II Cenelec UV type 3
- Weight : Approx. 19 kg.
2-8

HP8550
ELECTRICAL DIAGRAM
M
Timer
Watchdog
TB1
TB2
SK1
b1
M1
M2
L
N
SK3 SK5
S1
a1
a
b
B
N
Lp S2
B
N
Lp
-t
NTC1
-t
NTC3
-t
NTC2
La2 La4
La1
TCO1 TCO2
La3
SK4 SK6
b0
3-8

HP8550
PARTS LIST
4-8
Item Service code Description
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
4222 062 97081
4822 404 40639
4822 214 12272
4822 271 30619
4822 410 40417
4222 062 96230
4222 062 97091
4222 062 95020
4222 062 96280
4222 062 96290
4222 062 96300
4222 062 95920
4222 062 96310
4222 062 95250
4822 325 20102
4222 062 96320
4222 062 94580
4222 062 94570
4222 062 96330
4822 690 80147
Lamp housing US
Switch bracket
Starter HPA
Micro switch
Switch pin
17 tabs PCB
Lamp housing LS
Distance indicator
Screw (set 3.5x20 and 3.5x12)
Lamp HPA
Lamp IR
Thermal cut off 90 °C
Lamp holder assy IR
Reflector clamp
Lamp holder HPA
Reflector assy
NTC resistor 22W
NTC connector
Scent refill packages HB 080
Protecting Goggles HB 072
Item Service code Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
4222 062 95940
4222 062 95950
4222 062 95960
4222 062 95970
4222 062 97181
4222 062 95990
4222 062 96000
4222 062 96010
4222 062 96020
4222 062 96030
4222 062 96040
4222 062 96050
4222 062 96070
4222 062 97101
4222 062 97111
4222 062 97131
4222 062 97121
4222 062 96170
4822 265 30284
4222 062 96190
Paw cap R
Leg assy R
Leg assy L
Leg sliding plug (set)
Hinge assy
Paw cap L
Wheel
Fan assy
Slider assy
Main flex EU
Main flex UK
Main flex CH
Timer MS 65 (45 min.)
Timer housing middle
Timer housing front
Knob timer
Timer housing back
Watch dog
Connecting block 3S
Sea saw (set)

HP8550
EXPLODED VIEW PART A
2
6
4
3
15
7
5-8

HP8550
EXPLODED VIEW PART B
8
9
10
11
12
13
14
8
15
18
16
17
6-8

HP8550
EXPLODED VIEW PART C
20
35
19
24
27
28
26
25
23
22
21
29
33
34
37
38
36
30
31
32
7-8

HP8550
WIRING DIAGRAM
S1
Lp
NB
S2
Lp
NB
PCB2
PCB3
Watchdog
PCB1
Mains
N
L
TB2
N
L
TB1
La2
La1
SK3
TCO1
La4
La3
TCO2
SK4
SK5 SK6
M
Timer
SK1
b1
a1
b
a
b0
M1
M2
TB3
NTC2
NTC1
TB4
NTC3
Brown
Blue
Grey
Purple
Red
Yellow
Green
Black
White
8-8