Philips CitySpirit Street BDS480 User guide

CitySpirit Street
Mounting instruction
Type Voltage kg
Power
IEC
60598 IP65
Control
Method
on/off 12
Philips Lighting (China) Investment Co., Ltd.
No. 9, Lane 888 Tianlin Rd, Shanghai, China
Postalcode: 200233
ta
40°
BDS480/BDS482
IK09
46W
FrequencyCCT/Color Application
Temperature
4~6m
*：Dimming by program in IC inside power supply.
*Pole diameter 60mm
Color Ring
Red
Green
Blue
150
454
640
50mm
Unit: mm
单位: mm
8mm
220-240V
Dimming *
on/off
13.7
38W
38W
75W
75W
50/60Hz3000/4000K －40 ～40
No
S.Cx
0.32m²
BDS480 LED37/NW PSU 220-240V DW2 MP1 AUS
BDS480 LED35/WW PSU 220-240V DW2 MP1 AUS
BDS480 LED76/NW PSU 220-240V DW2 MP1 AUS
BDS480 LED70/WW PSU 220-240V DW2 MP1 AUS
BDS480 LED35/WW PSD 220-240V DW2 MP1 AUS
BDS480 LED37/NW PSD 220-240V DW2 MP1 AUS
BDS480 LED76/NW PSD 220-240V DW2 MP1 AUS
BDS480 LED70/WW PSD 220-240V DW2 MP1 AUS
BDS482 LED37/NW 220-240V GRN AUS
BDS482 LED37/NW 220-240V BL AUS
BDS482 LED37/NW 220-240V RD AUS
BDS482 LED35/WW 220-240V GRN AUS
BDS482 LED35/WW 220-240V BL AUS
BDS482 LED35/WW 220-240V RD AUS
AS/NZS
60598

2Driver Maintenance
2
或
Or
3
4
1. Open clip;
2. loosen screws at input end of power supply;
3. loosen screws at two ends of power supply;
4. loosen screws at output end of power supply;
5. Replace damaged power supply with good power supply, insert cables of two ends into relevant ports of connectors,
then tighten screws above mentioned.
1
Pole Mounting
1
1
2
16Nm
4mm
1.Put luminaire on the top of pole and diameter of pole is 60mm at junction;
2.Use hexagon socket screw key to tighten two screws, torque is 16 N.m.

3Glass Maintenance
3
1.Glass maintenance is only for non-color ring version, color ring version should be maintained in factory;
2.Use 3mm hexagon socket screw key to loosen fives screws to fix glass;
3.Take off damaged glass;
4.Replace good glass with damaged glass, don t forget plastics washer and sealing ring, then tighten screws.
3mm
1
2

1.The luminaire should be installed by a qualified electrician and wired in accordance with the latest IEE electrical
regulations or the national requirements.
2.Do not switch on before complete installation.
3.Don't hot swap. Don't operate when power on; Don't touch the lamp or the heating part, etc.
4.First switch off main supply and then replace broken glass.
5.First switch off main supply and then replace damaged power supply.
6.Non-replaceable LED.
7.Regularly check; Regularly clean, etc.
8. The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than 0.24m is not
expected.
9. The luminaire use physical tempered glass which become granular debris when broken.
Flat glass: Max 220，Min -40, t 200
10.If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
or his service agent or a similar qualified person in order to avoid a hazard.
11. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar
qualified person.
NOTES:
Disclaimer
1. Please mount and apply in accordance with the classification of the luminaire and the IP number as well as other notes marked
in mounting instruction. Do not immerse in water. The manufacturer will not be held responsible for IP protection failure caused
by improper usage above mentioned;
2. The manufacturer will not be held responsible for product damages, physical injuries, or property damages caused by
improper mount or improper usage;
3.The manufacturer will not be held responsible for product damages, physical injuries, or property damages caused by improper
usage or modifications of the product.