Philips HMP2500T User manual

www.philips.com/welcome
User manual
Always there to help you
Register your product and get support at
Question?
Contact
Philips
HMP2500T

1EN
Contents
1 Safety and notice 3
Safety 3
Compliance 4
Care of the environment 5
Copyright 5
Warranty 6
Trademark notice 6
2 Overview 7
Main unit 7
Remote control 8
3 Get started 11
Connect 11
Switch on or off 12
4 Play from DVB services 14
First-time setup 14
Tune in to TV/radio services 15
Use the Electronic Program Guide (EPG) 19
Use the Personal Video Recorder (PVR) 20
5 Play from a USB mass storage device 23

2EN
6 Setup 24
Program 24
Picture 25
Channel Search 25
Time 25
Option 25
System 26
USB 26
7 UpdatethermwarethroughaUSBstoragedevice 28
8 Specication 29

3EN
1 Safety and notice
Read and understand all instructions before you use this product. If damage is
caused by failure to follow the instructions, the warranty does not apply.
Safety
This 'bolt of lightning' indicates uninsulated material within the device may cause
an electrical shock. For the safety of everyone in your household, please do not
remove the covering.
The 'exclamation mark' calls attention to features for which you should read the
enclosed literature closely to prevent operating and maintenance problems.
WARNING: To reduce the risk of re or electric shock, the device should not be
exposed to rain or moisture and objects lled with liquids, such as vases, should
not be placed on the device.
CAUTION:To prevent electric shock, fully insert the plug. (For regions with
polarized plugs:To prevent electric shock, match wide blade to wide slot.)
Only use attachments/accessories specied by the manufacturer.
The product shall not be exposed to dripping or splashing.
Do not place any sources of danger on the product (e.g. liquid lled objects,
lighted candles).

4EN
ModicationoftheproductcouldresultinhazardousradiationofEMCor
other unsafe operation.
Warning
•Never remove the casing of this product.
•Never lubricate any part of this product.
•Never place this product on other electrical equipment.
•Keep this product away from direct sunlight, naked ames or heat.
•Ensure that you always have easy access to the power cord, plug or adaptor to disconnect the
product from the power.
•Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect
device shall remain readily operable.
Compliance
This product complies with the radio interference requirements of the European
Community.
Class II equipment symbol:
This symbol indicates that this product has a double insulation system.
Any changes or modications made to this device that are not expressly approved
by WOOX Innovations may void the user’s authority to operate the equipment.
Note
•The type plate is located on the bottom of the product.

5EN
Care of the environment
Environmental information
All unnecessary packaging has been omitted.We have tried to make the packaging
easy to separate into three materials: cardboard (box), polystyrene foam (buffer)
and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if
disassembled by a specialized company. Please observe the local regulations
regarding the disposal of packaging materials, and old equipment.
Your product is designed and manufactured with high quality materials and
components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product it means that
the product is covered by the European Directive 2002/96/EC.
Please inform yourself about the local separate collection system for electrical and
electronic products.
Please act according to your local rules and do not dispose of your old products
with your normal household waste. Correct disposal of your old product helps to
prevent potential negative consequences for the environment and human health.
Copyright
This item incorporates copy protection technology that is protected by U.S.
patents and other intellectual property rights of Rovi Corporation. Reverse
engineering and disassembly are prohibited.
Specications are subject to change without notice. WOOX reserves the right
to change products at any time without being obliged to adjust earlier supplies
accordingly.

6EN
Warranty
• Never attempt to repair the product, this could lead to the risk of injury,
damage to the product and will void your warranty.
• Use the product and accessories only as intended by the manufacturer.The
caution sign printed on the back of the product indicates risk of electric
shock.
• Never remove the cover of the product. Always contact our Customer
Support for service or repairs.
• Any operation expressly prohibited in this manual, or any adjustments and
assembly procedures not recommended or authorized in this manual shall
void the warranty.
Trademark notice
Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke
Philips N.V. and are used by WOOX Innovations Limited under license from
Koninklijke Philips N.V.”
HDMI, and HDMI logo and High-Denition Multimedia Interface are trademarks
or registered trademarks of HDMI licensing LLC in the United States and other
countries.
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
The USB-IF Logos are trademarks of Universal Serial Bus Implementers Forum, Inc.
®

7EN
2 Overview
Through HMP2500T, you can do the following on your high-denition TV (HDTV):
• Receive digitalTV/ radio programs from the latest Digital Video Broadcasting
(DVB-T2) services;
• Schedule your watching, listening, or recording of the programs;
• Play media that you store on the USB device.
Main unit
a MAINS ~
• AC power cord
b L / R
• Connectors for audio output
c Pr / Pb / Y
• Connectors for component video output
d VIDEO
• Connector for video output
e HDMI
• HDMI connector for audio/ video output
f RF LOOP THROUGH
• Output connector for external TV antenna
g RF IN
• Input connector for external TV antenna
OK
k
a
i
h
g
f
b
c
d
e
j

8EN
h
• USB connector for media play and power charging of a USB mass
storage device
i Status display
j
• Press the button to switch on;To switch off, press and hold the button
for more than three seconds.
CH+/CH-/ /
• Navigate through the list of options
OK
• Select an option
CH+/CH-
• DVB: Select the next or previous service
/
• Increase or decrease the volume
k Power indicator
Remote control
Switch HMP2500T on or to standby mode
• Press
Select TV resolutions
• Press TV MODE repeatedly
Select media sources
TV / RADIO
• Press the button repeatedly to switch between the TV and Radio
modes
USB
• Switch to the USB mode
Navigate through options
• Navigate through options
OK
• Conrm the option
/ EXIT
• Exit

9EN
• USB: Back one level
Select a TV/ radio service
(CH+) / (CH-)
• Switch to the next or previous channel
0-9
• Numeric keys for the entry of channel numbers
EPG (Electronic Program Guide)
• List of all TV/ radio programs
• Create your watching/ listening schedule
FAV
• Access the list of your favorite services
Use the PVR (Personal Video Recorder)
LIST
• Access the recorded programs
REC
• Record current program
• Access the programs in your watching/listening/recording schedule
Playmediales
• Start, pause, or resume the play
/ EXIT
• Stop the play
/
• Skip to the previous or next media le
/
• Search backwards or forwards within current le
• Press repeatedly to select a search speed
GOTO
• Skip to a point of time for media play
Red / Green buttons
• Rotate a photo
• USB: Zoom in or out the image
• TV: Select the aspect ratio options
REPEAT
• Select the repeat options

10 EN
INFO
• Display the information about current program/ le during play
SUBTITLE
• Access subtitle options
AUDIO
• Access the options of audio languages
• Access the options of audio tracks
TTX
• TV/ Radio: Switch teletext on or off
Change the volume
/
• Increase or decrease the volume
• Mute/ unmute
Select setup options
• Press SETUP

11EN
3 Get started
Connect
a ConnectHMP2500Ttoahigh-denitionTV(HDTV)throughanHDMI
cable (not supplied).
b Connect your TV antenna cable (not supplied) to RF IN.
c Connect the power cord to power.
To connect to a TV through AV cables
Audio/video cables (not supplied):
HDMI IN
SOURCE
TV
HDMI
Cable
3
AV
L
RVIDEO
LRVIDEO

12 EN
Component video cables (not supplied):
• Make sure that the plugs and sockets match in color.
Switch on or off
1 On HMP2500T, press on the remote control to switch on.
• Alternatively, press on the main unit.
2 On the TV, switch to the input source of HMP2500T:
• On the remote control of your TV, use the source button to select the
input source of HMP2500T.
Pr Pb
Y
L
RVIDEO
AV
Pb/CbPr/CrY
OK
SOURCE
TV
AV
HDMI 1
HDMI 2
HDMI 3
Side HDMI
Side AV

13EN
3 To switch HMP2500T to standby mode, press again on the remote
control.
» The power indicator lights up red.
• Alternatively, press and hold on the main unit for more than three
seconds to switch off.
Auto standby
If there is no button press or media play on HMP2500T for three hours,
HMP2500T can switch to standby mode automatically to save power.
On the remote control, press SETUP. Go to to switch on [Auto Standby].

14 EN
4 Play from DVB services
First-time setup
The rst time you use HMP2500T, do the following setup:
1 In [OSD Language], select the language for the onscreen menus.
2 In [Country], select the country of your current location.
3 In [Channel Search], press or OK to start auto search.
» HMP2500T starts to search for available services.
» When the auto search is complete, the rst TV service starts to play.
Auto search
When you move to a new place (such as a new city or country), restart auto
search for better reception.
1 On the remote control, press SETUP.
2 Go to and select [Auto Search].
» HMP2500T starts to search for available services.
» When the auto search is complete, the rst TV service starts to play.
Installation Guide
OSD Language English
England
EXIT Confirm
Country
Channel Search
EXIT OK

15EN
Manual search
You can search for services by channel number or frequency.
1 On the remote control, press SETUP.
2 Go to and select [Manual Search].
Tune in to TV/radio services
1 On HMP2500T, switch to the TV or radio mode.
• On the remote control, press TV / RADIO repeatedly.
» You switch to the last played service.
2 To tune in to a service by channel,
• Press (CH+) / (CH-), or
• Use the numeric keys 0-9 to enter channel numbers.
To tune in to a service by service information,
• Press EPG. Press to switch between services.
To tune in to your favorite services,
• Press FAV.
Select from the list of services
1 In the TV or Radio mode, press EPG.
» You can select from the list of available TV/ radio services.
2 Press to switch between services.
Sort services in the EPG
To display services as needed, you can sort the services in different ways.
1 On the remote control, press SETUP.

16 EN
2 Select > [Sort]:
[By LCN]: Services are sorted by Logical Channel Number (LCN).
[By ONID]: Services are sored by Original Network ID (ONID).
[By Service Name]: Services are sorted by service name.
[By Service ID]: Services are sorted by service ID.
3 Press to switch between options.
Create a list of favorites
On the remote control, press FAV.You can access the services that you have
added to the list of favorites.
To add/ remove a service
1 On the remote control, press SETUP.
2 Select > [Program Edit].
• Enter your password (000000 by default).
» A list of services is displayed.
Program
Program Edit
EPG
Sort
LCN
By Service Name
O
Return
EXIT
Conrm
OK

17EN
3 To add a service,
• Select a service. Press FAV.
» A pop-up screen is displayed for you to select the program type.
» The Favorite icon is added next to the service.
4 To remove the service,
• Select the service. Press FAV again.
» The Favorite icon is removed.
To access a favorite service
1 On the remote control, press FAV.
» A pop-up screen is displayed for you to select a service.
2 To switch between program types, press .
3 To select a service, press and OK.
Re-assign channel numbers
1 Switch off the logical channel number (LCN).
a On the remote control, press SETUP.
b In > LCN, press to select [Off].
2 Move a service to the channel number that you want to assign:
a In > [Program Edit], select a service.
Enter your password (000000 by default).
b On the remote control, press the Red button.
» The Move icon is added next to the service.
c Press / to move the service.
d To stop moving, press the Red button again.
» The Move icon is removed.

18 EN
Edit the program list
By editing the program list, you can lock services, skip services, or change the
service name.
1 On the remote control, press SETUP.
2 Select > [Program Edit].
• Enter your password (000000 by default).
» A list of services is displayed.
» You can edit the program list as needed.
Lock a service
You can set a password for some services.
1 Select a service.
2 Lock the service:
• On the remote control, press the Yellow button.
» The Lock icon is added next to the service.
» To watch the locked service, enter your password (000000 by
default).
3 To unlock the service:
• Select the service. Press the Yellow button again.