Philips LRM3120K/27 User manual

Home power
LRM3120K/27

The alarm unit has a low battery circuit.
When the batteries reach a low level,
the indicator light will ash slowly.
Average battery life for typical usage is
up to one year.
LEARN
Home/
away
switch
Alarm/
chime
switch Magnet
Indicator
light
Learn
button
Double-
sided tape
Mounting
plate
Screws
Battery
compartment
Low Battery Indicator
3

The keypad controlled door alarm
requires three (3) AAA Alkaline
batteries (not included).
To install the batteries:
1. Remove screw from battery
compartment door located
on back of the unit. Slide o the
door in the direction of
the arrow.
2.Insert three (3) AAA batteries
noting the polarity diagram inside
the battery compartment.
3.Replace door and
secure screw.
Installing Batteries
4

The keypad allows you to set a
personal 4-digit code for arming and
disarming the alarm.
1. Remove screw from battery
compartment door located on
back of the unit. Slide o the door
in the direction of the arrow.
2.Press the LEARN button.
3.The red light on the front of the
alarm will blinkfor 15 seconds.
During this time, input your 4-digit
code. A beep will conrm each
input. The unit will ash a green
light 3 times to conrm the new
4-digit code has been saved.
4.Replace cover and
secure screw.
Creating Your Personal Alarm Code
5
LEARN
Learn
button

1. Select desired location for
alarm. The alarm is designed to
mount to the door frame or to
the door itself. Use either the
provided screws (for permanent
mounting) or double-sided tape
(for temporary mounting). The
recommended location is the
back of the door, with the magnet
mounted to the door frame.
Mounting the alarm to the door
ensures that the alarm will not be
damaged by opening and closing
the door.
Installation
Recommended Mounting Method Alternate Mounting Method
6

Note that the magnet may be
mounted to either side of the
alarm as long as the arrows line
up.
IMPORTANT:Whether mounting
to the door or door frame, the gap
distance between the alarm and
magnet must be 1/2” or less.
2.Attach the mounting plate to
the back of the alarm. Peel the
protective covering from one side
of the double-sided tape and then
apply to mounting plate. Remove
protective covering from the back
side of the double-sided tape
and lightly mount the alarm in
the desired position. Make sure
Distance must be less that 1/2”
7

the surface you are mounting to
is clean and dry. For best results,
clean the mounting surface with a
mixture of 50% isopropyl alcohol
and 50% water.
Do not apply rm pressure until
location is nal.
NOTE: When mounting to a door
frame, the mounting plate mounts
o-center to the left or right in
order to position alarm closest to
the edge of the door.
8
Double-sided tape
Mounting Plate
Alarm

3.Using double-sided tape, lightly
attach the magnet to the opposite
edge next to the alarm. Line up
the arrows of the alarm and the
magnet. Ensure the distance
between the two pieces is 1/2”
or less. To test the gap distance,
slide the ALARM/CHIME switch to
CHIME and open the door. If chime
sounds, then the gap distance is
correct. If it does not sound, move
either the alarm or magnet closer
so that gap distance is 1/2” or less.
4.Once you have conrmed the
correct positioning of the magnet
and alarm, lift the alarm o the
mounting plate and apply rm
pressure directly to the plate
itself. Once secured, reattach the
alarm to the mounting plate.
5.Apply rm pressure to the magnet
to secure its position as well.
9

1. Locate ALARM/CHIME switch on
right side of the alarm unit.
2.Slide switch to ALARM position.
3.Choose HOME or AWAY on the left
side of the alarm unit.
HOME MODE
In HOME mode, the alarm will sound
when the gap between the alarm and
the magnet is greater than 1/2” (i.e.
the door is opened).
AWAY MODE
In AWAY mode, there will be a 45 second
exit delay before the unit is armed.
The alarm’s indicator light will ash
red quickly, alerting you that the unit
has been activated and has begun the
45-second count down. The delay allows
time for you to leave the protected area
without triggering the alarm. When
returning to the protected area, there is
a 30 second delay to allow time to enter
4-digit code before the alarm will sound.
10
Operating In The Alarm Mode

Arming the Alarm:
1. Arm the alarm by pressing your 4-digit
code. When the 4 digit code is entered
correctly the unit will ash a green
light once. NOTE: if the 4 digit code is
entered incorrectly, the unit will sound
a higher tone and ash red 3 times.
Disarming the alarm:
1. Enter your 4-digit code to disarm the
alarm. When the fourth digit of your
code is entered, the unit will respond
with two tones and will ash a green
light twice.
2. Enter the correct code anytime after
the alarm has sounded to deactivate.
NOTE: When testing, a cloth can be
used to cover the alarm to reduce risk
of hearing damage.
Incorrect code
If an incorrect code is entered, the
unit will sound a louder beep and
will ash red 3 times. Re-enter the
correct code after the light stops
ashing.
11

1. Locate ALARM/CHIME switch on
right side of unit.
2.Slide switch to CHIME mode.
Activating the chime:
1. The chime will now sound
immediately if the distance
between the alarm and magnet is
greater than 1/2” (i.e. the door is
opened).
Deactivating the chime:
1. To deactivate the chime slide
ALARM/CHIME switch to ALARM
position.
To clean the alarm housing, use a soft
cloth slightly dampened with water
and wipe dry. Do not use chemical
agents as this may damage and
discolor the unit.
12
Care and Maintenance
Operating In The Chime Mode

13
Warning
Limitations of Alarm Products
This product should be tested periodically to
make sure it is working properly. The product, if
used properly, may reduce the risk of burglary,
robbery, or other adverse events. However,
JASCO is not an insurer, this product is neither
insurance nor a guarantee that such an event
will be prevented, and users should protect
themselves with proper insurance. JASCO makes
no representation that this product cannot
be compromised or circumvented, that it will
provide an adequate warning, or that it will
prevent any personal injuries, property damage,
or other losses. Like any alarm product, including
expensive commercial systems, it may be
bypassed, it is subject to compromise, and it may
fail to warn for a variety of reasons, including,
but not limited to: improper installation or
positioning; improper maintenance; tampering;
dead or improperly installed batteries; sensing
limitations; component failures; receivers;
for infrared products, intrusions may be
outside of a product’s designed range and
certain environmental conditions may impact
performance and audible alarm signals may
be outside of hearing range, muted by doors,
walls, and oors, unheard by deep sleepers or
the hearing-impaired, or overwhelmed by other
sounds.

Risk of personal injury
• Prolonged exposure to alarm siren may cause
permanent hearing loss
Battery Warning
• Remove batteries before storing the Alarm for
extended periods
• Batteries may leak harmful liquids or ignitable
materials or explode causing injury and product
damage
• Do not mix old and new or other battery types
• Replace all batteries at the same time
• Replace fully discharged batteries immediately
For indoor use only; do not use in wet locations.
Warning
14
MADE IN CHINA
Philips and the Philips Shield Emblem are registered trademarks
of Koninklijke Philips N.V. and are used under license. This product
has been manufactured by and is sold under the
responsibility of Jasco Products Company, and
Jasco Products Company LLC, 10 E. Memorial
Rd., Oklahoma City, OK 73114 is the warrantor in
relation to this product.
This product comes with a 1-year limited warranty.
Visit www.philips.com/support for warranty details.
Questions? Contact our US-based Consumer Care
at 1-844-816-0320 between 7AM–8PM, M–F,
Central Time.

Suppliers Declaration of Conformity | Model #:
LRM3120K/27 | Jasco Products Co., 10 E. Memorial Rd,
Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for
any radio or TV interference caused by unauthorized
modications to this equipment. Such modications could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment
and receiver.
— Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV
technician for help.
15

16
Scan to watch a step-by-
step instructional video or
visit byjasco.com/47713i
Get exclusive, web-only
deals and more! Scan here
or visit byjasco.com/deals
Like our product?
Leave us a review on
Amazon.com or your
favorite retailer website!
Having issues and
need support?
Call our U.S.-based
experts Monday–Friday,
from 7AM–8PM (Central)
1-844-816-0320
Product
instructions
made easy
For additional Philips home
security visit our website!
byjasco.com/security
Need more home
security devices?
Register
your Philips
product
THANK YOU FOR YOUR PURCHASE!

Home power
LRM3120K/27

La unidad de alarma tiene un circuito
de batería baja. Cuando las baterías
lleguen a un nivel bajo, la luz indicadora
se encenderá y se apagará lentamente.
La vida promedio de las baterías es de
hasta un año para una utilización normal.
Indicador de batería baja
LEARN
Interruptor
en casa/
fuera de
casa
Interruptor
de alarma/
campana Imán
Luz
indicadora
Botón
crear
Cinta doble faz
Placa de
soporte
Tornillos
Compartimento
para baterías
3

La alarma para puertas controlada por
teclado funciona con tres (3) baterías
alcalinas AAA (no vienen incluidas).
Para instalar las baterías:
1. Retire el tornillo de la tapa del
compartimento para baterías que se
encuentra en la parte de atrás de la
unidad. Deslice la tapa en dirección
de la echa.
2. Inserte tres (3) baterías AAA
de acuerdo con el diagrama de
polaridad que se encuentra en el
compartimiento para baterías.
3. Vuelva a colocar la
tapa y asegure el
tornillo.
Cómo Instalar Las Baterías
4