Philips WP3893 User manual

Register your product and get support at
WP3893
WP3892
EN User manual 3
KO사용 설명서 21
PT Manual do utilizador 39
RU Руководство
пользователя 59
ZH-TW 使用手冊 79
ZH-CN 用户手册 97
132
Contact information 134

3
Make sure the Pure Water Dispenser is
mounted stably in vertical position.
Make sure you install the Pure Water
Dispenser in accordance with state and local
regulations.
Do not install the Pure Water Dispenser in
direct sunlight or in a hot location, e.g. close to
a stove or over the cooker.

and clean containers for not more than 48
hours.
Do not store the water in a water pot

recontaminate the water.


in this user manual.
Use the PureFlush function if the Pure Water
Dispenser has not been used for 2 days.
Always handle the quartz tube carefully during
cleaning.
Do not use an extension cord to supply
power to the Pure Water Dispenser.
Do not connect the Pure Water Dispenser to
a hot water tap.
Do not connect ordinary tubes or hoses to
the water outlet to collect water from the
Pure Water Dispenser.
Do not open the appliance door while you
are collecting water from the Pure Water
Dispenser.
Do not connect the Pure Water Dispenser to
a drain.

affects the performance of the Pure Water
Dispenser.
Do not place anything on top of the Pure
Water Dispenser.
Do not hang anything on the tube and mains
cord of the appliance.
Do not use any chemical to disinfect or clean
the Pure Water Dispenser externally or
internally (tubes etc).
Do not clean any plastic parts in a dishwasher
or boil them.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1 Important
Read this user manual carefully before you use the
appliance and save it for future reference.
1.1 Danger
Do not spill water or any other liquid onto
the appliance.
1.2 Warning
Check if the voltage indicated on the
appliance corresponds to the local mains
voltage before you connect the appliance.
If the mains cord is damaged, you must have it
replaced by Philips, a service centre authorised

order to avoid a hazard.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
Do not close the water outlet when the Pure
Water dispenser is in operation or in waiting
mode.This will create pressure on all internal
components and can lead to leakage and a
hazardous situation.
1.3 Caution
Install the Pure Water Dispenser at a
convenient and safe location where it poses
no risk of injury.
Make sure you mount the Pure Water
Dispenser properly according to the
instructions in this user manual.
•
•
•
•
•
•
•
•
ENGLISH

4
2 Your Pure Water
Dispenser
1 Front Access Panel
2 Door Panel
3 Back Panel
4 Faucet / Tap
5 FaucetCap
6 Display Panel
7 TopCover
8 UVAccessCover
9 UVChamber
10 DualFilterUnit(lter)
11 Macro Filter
12 MainsCord
13 PowerON/OFFSwitch
14 Mounting Holes
15 WaterInletConnector
2.0.1 Pure Water

bigger particles are removed from input drinking
water, then it passes through a sediment and

Chlorine,Volatile Organic compounds and cysts
are removed. Finally the water passes through the
UV chamber where the UV rays destroy bacteria’s
and virus, giving you absolutely safe and pure
drinking water.
Pure water is our life: it cleanses our body, enlivens
our mind and rejuvenates our soul Pure water,
though a basic necessity, is within the reach of
only a few.With a mission to help millions of
people gain access to pure drinking water, Philips,
the global master of sense & simplicity, offers the
ultimate Pure Water Dispenser.
Our Pure Water Dispenser combines the
excellence of European technology with sleek,
elegant styling and simple operations to offer
our customers an enjoyable pure drinking water
experience.We invite you and your family to live
this pure water experience.
Do not replace the PhilipsTUV PLS 9W lamp
with any other ordinary or UV lamp.This will
affect the microbiological performance of the
Pure Water Dispenser and make it ineffective.
When you replace the UV lamp and/or clean
the quartz tube, make sure you place all parts
back according to the instructions in this user
manual.
Do not forget to clamp the tube that
connects the Pure Water Dispenser to the
tap. Improper clamping of the tube may lead
to leakage.
Hold a container of appropriate capacity

water from the Pure Water Dispenser.A too
small container may lead to leakage and a

•
•
•
•

5
ENGLISH
1
2
6
3
45
11
15
8
7
9
14
13
10

6
4 Getting Started
4.0.1 Installation
Make sure the routing of the pipe and wire to
the socket are proper.
In case the water pressure in your area is

we recommend the use of a suitable domestic
water pump.
If the pressure is higher than the maximum

reducing valve is required.
DNote:
ItisrecommendedthatthePureWater
DispenserbeinstalledbyTrainedService
Technicians.
Always install the Pure Water Dispenser in a
vertical position. Do not install it inclined or
horizontally.
Do not connect to an electrical point placed
below the Pure Water Dispenser.
Drill 3 holes on the wall as shown in picture.
Distance of the Pure Water Dispenser should
be 1m from the tap.
•
•
•
•
•
•
•
150mm
192.5mm
150mm
192.5mm
3 Certications
This Philips Pure Water Dispenser conforms
to the highest standards for contaminant
reduction, structural integrity and material
safety and thus ensures that you get Pure
Water Made Easy - Always.The following

3.0.1WQAGoldSealCertied:
WQA (Water Quality Association, USA)
only awards the Gold Seal to those systems,
components, or additives that have met or
exceeded industry standards for contaminant
reduction, structural integrity, and material
safety.

to NSF/ANSI 42 for the removal of chlorine
and particulates (removes all classes of
particulates from Class I till ClassVI - particle

removal of turbidity, volatile organic chemicals

for microbiological dis-infection. Both the

by WQA.
3.0.2TestedbyKiwaWaterResearch:
Microbiological performance tested by Kiwa
Water Research (The Netherlands) according


•
•
•
•
1m

7
5 Features
1 IntelliFill:Purieswaterinpre-setquantity,
eveninyourabsence
When the Pure Water Dispenser senses
water pressure, IntelliFill will start purifying and
dispensing water up to the amount you have

when you are away or asleep, and you will
always be sure of having enough pure water
when you need it
2  PowerUV+:UsesAdvancedUVtechnology
andActivatedCarbontopurifywater.
Advanced state-of-the-art UV (PLS)
technology destroys known waterborne
viruses, bacteria, parasites and amoebae while

improves taste and removes turbidity, chlorine,
volatile organic chemicals (VOC’s), cysts and
larger micro-organisms.
3  PureProtectAlert:PureProtectAlertwarns
youwhenthelterneedsreplacement.
The Pure Water Dispenser should be placed at
eye level or a bit above eye level from the LCD
display panel.
Connect the Pure Water Dispenser to the

Connect the Pure Water Dispenser to
running tap water
4.0.2DisplayPanelDescription
1 PowerIndicator
2 BatteryIndicator(onlyformodelNo.WP
3893)
3 UVIndicator
4 WaterAvailabilityIndicator
5 FilterIndicator
6 LCDDisplay
7 AutoModeIndicator
8 Mode Button
9 ’Litres’(Qty)settingbutton
10 PuricationStageIndicator
11 Dispense Button
•
•
ENGLISH
2
5
6
7
9
10
11
1
3
8
4

8
In the event of a mains power failure, the Pure
Water Dispenser automatically switches over
to the battery, making it possible to dispense

supply is available, the battery is automatically
recharged.
6  PureFlush:PureFlushushespipesandUV
chamber.
At the push of a button, PureFlush

UV chamber of the Pure Water Dispenser.


Dispenser has not been used for 2 days.
Thanks to PureFlush, you can be sure of pure
water even if you have been away for a while.
7  Tilt&TwistFilterchange:Tilt&Twist
mechanismforeasylterreplacement.

do yourself, thanks to the simple Tilt & Twist
mechanism.
8  PowerSave:PowerSaveensureslow
electricity consumption

PureProtect Alert sends out a signal.There will

after the signal.
4  PureProtectLock:PureProtectLock
guaranteeswaterquality.
The PureProtect Lock guarantees high quality


water consumption after the PureProtect
Alert signal), the Pure Water Dispenser will
be locked so that no more water can be
dispensed.The Pure Water Dispenser also

mounted properly, or if the UV lamp fails.
5  RechargeableBatteryBackUp:Rechargeable
batteryensuressupplyduringpowerfailure
(onlyformodelno.WP3893)

9
6 UsingYour Pure
Water Dispenser
DNote:
OpenthetapconnectedtothePure
WaterDispenser.
Switchonthemainspowersupplytothe
PureWaterDispenser.
6.0.1 Purifying in Manual Mode: (2 Easy
Steps)
1  PressthePowerbuttononthePureWater
Dispenser

Power LED 3 will be ON
LCD display will be ON
Battery LED will glow green, if AC supply
is available Else RED, on battery. If battery


(Only for model WP 3893).
The Pure Water Dispenser checks for
water supply
The Pure Water Dispenser checks the
Filter c
The Pure Water Dispenser checks the UV

in a sequence – RED,YELLOW, GREEN

Dispense button d
mode= manual)
2  PressDispensebutton
The Pure Water Dispenser starts
dispensing water. (While dispensing,
the quantity of water dispensed would
be shown on the LCD display & the
Dispense button LED glows a constant
green)
Again, press the dispense button dto
stop dispensing water.The dispense

to dispense again)
•
•
•
•
•
•
•
•
•
•
•
•
•
This Pure Water Dispenser has low electricity
consumption and is rated at a maximum of

the UV lamp switches off when the Pure

minutes.
9  SmartDisplay:SmartDisplayforeasy
settingsandfeedback.
The LCD display gives clear, legible feedback
and is easy to use when programming settings.
10 AudibleIndications:Audiblereminderlets
youknowwhenthePureWaterDispenseris
on.
While the Pure Water Dispenser is dispensing
water, an optional audible reminder will notify
you that the Pure Water Dispenser is on.
ENGLISH

10
The LCD display would retain the
previously selected quantity so that you

quantity.
To cancel/reset the existing setting, either
press the Mode button (switch to manual
mode) or switch off the power button.
To reset quantity, press the Litres button
DNote:
Incasewatersupplyshutsoffwhile
dispensinginAutomode,thePureWater
Dispenser will program itself to dispense
later.
TheLCDdisplayshowspendingquantity,
whichyoucanchangeifrequired.
ThePureWaterDispenserisnowready
todispensethepending/changedquantity
oncethewatersupplyresumes.
Ensurethatyouplaceacontainerof
appropriatecapacitytocollectthepuried
water.Tocanceltheexistingsetting,switch
offthePureWaterDispenser.
6.0.3SettingthePureWaterDispenser
whenwaterisnotavailable
1  PressthePowerbuttononthePureWater
Dispenser
When water is not available the Pure
Water Dispenser switches to Auto mode
f.
Water indicator bwill glow RED

2  PressLitresbutton(toselectquantity)
Select the quantity of water you need to
dispense when water supply resumes
Once you select the quantity the

3  PressDispensebutton
The Dispense button LED switches off
The Water LED b
means that the Pure Water Dispenser has
programmed itself for later dispense when
water supply resumes
•
•
•
•
•
•
•
•
•
•
•
•
•
•
DNote:
Incasewatersupplyshutsoffwhile
dispensinginManualmode,thePureWater
DispenserwillswitchtoAutomode.
IfyouwanttoprogramthePureWater
Dispenserforalaterdispense,(when
watersupplyresumes)selectaquantity
bypressingLitresbutton.TheLCDdisplay
willshowtheselectedquantity.
ThePureWaterDispenserisnow
readytodispensethisselectedquantity
automatically,oncethewatersupply
resumes.
6.0.2 Purifying in Auto mode: (4 Easy
Steps)
1  PressthePowerbuttononthePureWater
Dispenser.
Wait till the Dispense button dstarts

2  PresstheModebutton
The Pure Water Dispenser goes into
AUTO fmode
The Dispense LED switches off, LCD

3  PresstheLitresbutton
Pressing this button would let you select
the quantity of water required
A single press of the button increases the

Press and Hold the button for fast
increment in quantity. Once the quantity is
selected, the Dispense button dwill start

4  PresstheDispensebutton
The Pure Water Dispenser would start
dispensing water
The LCD display shows a reverse count
as the water is being dispensed. (Pending
quantity would be displayed)
The Pure Water Dispenser would
automatically stop once it has dispensed
the selected quantity
•
•
•
•
•
•
•
•
•
•
•
•

11
6.1Otherfunctions
6.1.1Pureush

either of the 3 conditions.
1st time use of the Pure Water Dispenser
If the Pure Water Dispenser is not used for
more than 2 days

Dispenser would perform the Pure Flush


1  SwitchonthePureWaterDispenser.
Wait till the Dispense button LED starts

2  PressandholdtheDispensebuttonfor4
sec
The Pure Water Dispenser will start


so make sure that you place a container
below the dispenser.
BWarning:
Donotusethisushedwaterfordrinking.
Dispense button LED would glow a constant
green as an indication of Pure Flush in
progress.All the other indications (LEDs)
would be OFF.
DNote:
TocancelPureFlushmidway,pressthePower
ButtontoswitchoffthePureWaterDispenser.
6.1.2 Audio on/off
The Pure Water Dispenser plays an audio while
it’s dispensing water.This is just to remind you that
the dispensing is in progress.The factory (Default)
setting for this audio would be “AUDIO OFF”.You
can switch the audio ON if required Power on
the Pure Water Dispenser.
1  PoweronthePureWaterDispenser.
•
•
•
•
•
•

(Waiting for Water) Stand-by mode
Make sure that you place a container
of appropriate capacity below the Pure
Water Dispenser to collect the dispensed
water
When water supply resumes, the Pure
Water Dispenser dispenses the pre-
selected quantity and stops automatically

Dispenser goes into Stand-by mode
DNote:
In(WaitingforWater)Stand-bymode,all
theLED’s&theLCDwouldswitchoff,
exceptforthepower3,batteryzthe
WaterLED(Flashing).
Afterdispensingwater,thepresetquantity
remainsonscreen.
6.0.4 Battery (only for WP 3893)
1  BatteryCharging
To charge the battery, switch on the mains
power supply.
Switch on the Power button to start
charging the battery.
During charging the Battery LED z

Once the battery is fully charged, the
Battery LED zwould glow constant
green.
Charge the battery for 14 hours before

time will be 12 hours for a full recharge.
DNote:
ThePureWaterDispenserwillswitchto
Standby(PowerSaving)modeafter10minutes
butthebatterywillcontinuetocharge.
Remarks: Lead acid gel batteries lose their life
when not charged regularly.The performance and
functionality of the battery is dependent directly
on the charging pattern.We recommend that the
battery is charged regularly till it gets fully charged.
•
•
•
•
•
•
•
•
•
•
•
ENGLISH

12
7 Maintanance
7.0.1 Cleaning
1  HowtocleanyourPureWaterDispenser.
Clean the Pure Water Dispenser regularly
using a damp (not wet) cloth.
Do not pour water over the Pure Water
Dispenser.
Do not use corrosive and abrasive
cleaning products.
If not used for 2 days: Press & hold the


2  HowtocleantheMacrolter.
Switch off the Pure Water Dispenser.
Turn off the water supply to the Pure
Water Dispenser.
Unscrew the cap (and hold it in a vertical
position to avoid any spillage of water).

Rinse it in running water and clean the
dirt on the mesh.

the same position.
Close the cap.
Open the tap and start using the Pure
Water Dispenser.
7.0.2Replacement
DNote:
SwitchoffthePureWaterDispenserbeforeyou
commencelterchange.
•
•
•
•
•
•
•
•
•
•
•
•
Wait till the Dispense button LED starts

mode).
2  Pressthehold“Litres”button.
When you Press and hold the “Litres” button
for more than 4 sec the “During Dispense”
audio will be turned ON.
To Switch the audio OFF, press and hold the
“Litres” button again for 4 sec.
DNote:
Toperformthisoperation,makesurethat
thePureWaterDispenserisintheManual
mode,andtheDispensebuttonLEDis
ashing(Readytodispense).
TheAudioON/OFFsettingwillchange
todefault(Factorysetting–“AUDIO
OFF”)whenthePureWaterDispenseris
poweredonnexttime.
•
•

13
5  Turnandclickopentheltercap.
6  Pulloutthecombinedlterslowlywithhelp
ofthehandleavailableonthetopofthe
lter.
7  Replaceitwithanewone.Pushitdowntill
ittsrmly.
8  Toclosetheltercapalignthearrowonthe
capwiththearrowonthelterhousingand
pressdownrmly.
9  Rotatethecapinaclockwisedirectionto
close.
1  Whendoyoureplacethelter?


litres, the Pure Water Dispenser gives you

You can continue to dispense water

period but the Filter LED will always



litres. In this scenario the Filter LED will
glow constant RED and the Pure Water
Dispenser will not dispense water unless
the Filter is replaced.
DNote:
Itisrecommendedtochangethelter
afterevery6monthseventhoughyou
mightnothaveconsumed3000litres.
Filterlifeissubjecttoactuallevelof
impuritiesinyourwatersupplyandthus
mightexpirebefore3000litreswithout
anyalert/warning.
2  SwitchoffthePureWaterDispenser.
3  Openthedoor.
4  Pullthelterunittowardsyouwiththehelp
oftheleverfromitsmountedplaceand
slightlytiltit.
•
•
•
•
ENGLISH

14
(A) Press and hold the “Litres” button.
(B) Press and hold the “Dispense” button.
(C) Make sure that you press and hold
both these buttons together for more
than 4 sec.
The Pure Water Dispenser will now

The Filter LED will switch off which means
that the new Filter is registered.
If the Filter warning still persists, try
repeating steps
(A), (B), (C).
Once the new Filter is acknowledged the
Pure Water Dispenser will automatically

Make sure that you either drain that water


it later.
DNote:
Ifyouhavereplacedthelterduringthe
warningperiodwaituntiltheDispense
buttonLEDstartsashing(Readyto
dispense-Manualmode)andthenfollow
steps(A),(B),(C).
Ifyouhavereplacedthelterafterlter
expiry,theFilterLEDwillglowconstantly
afterwhichfollowsteps(A),(B),(C).
Do not forget to keep a container (10
litres)tocollecttheushedwater.
7.0.4ReplacingUVLamp
DNote:
Whilereplacingthenewlampassembly
pleaseensurethatitiswithPhilips12NC
-421530875020.
SwitchoffthePureWaterDispenser
beforeyoucommenceUVLamp
replacement.
1  RemovetheUVaccesscover.
•
•
•
•
•
•
•
•
•
•
•
•
•
10 Pushbackthelterunitintoitsplace.
11 Closethedoor.
DNote:
Eachtimethatyoureplacethelter,ensurethat
youcleantheMicrolteraswell(seesection
7.0.1Cleaning).


replacement.The Pure Water Dispenser will start


7.0.3FilterReplacementConformation

1  SwitchonthePureWaterDispenser.


Wait till the Dispense button LED starts

mode).

expiry the Filter LED will be constantly
ON.
2  Pressandhold“Litres”buttonandthe
“Dispense”buttontogetherfor4sec.
•
•

15
7  Re-connectthewireconnectors.
8  ClosetheUVaccesscover.
7.0.5CleaningtheQuartzTube
DNote:
Recommended cleaning cycle of Quartz
tube:Onceeverysixmonths.
Cleanwithcareasbreakageofthequartz
tubemightcauseinjury.Donottamper
withthequartztube(applyglueetc).
SwitchoffthePureWaterDispenser
beforeyoucommencethecleaningof
Quartztube.
Alwaysremembertoputtherubber
O-ringandquartztubeinthecorrect
position.
1  ToremovetheQuartztubefromtheUV
chamber,followthestepsfrom1to8of
section7.0.4.
2  OnceyouremovetheUVLampassembly,
pullouttheQuartztubewiththerubber
O-ring.
3  RemovetherubberO-ring.
•
•
•
•
2  DisconnecttheUVLampwireconnectors.
3  Unscrewthe“UVLampRetaining”cap.
4  RemovetheUVLampassembly(Lamp,
Rubberseal&Lampsupport).
5  InsertthenewUVlampassemblybackinits
position.
6  FixtheLampretainingcap.
ENGLISH

16
8 Disposal
Do not throw away the appliance with the
normal household waste at the end of its life,

recycling. By doing this, you help to preserve
the environment.
The built-in rechargeable batteries contain
substances that may pollute the environment.
Always remove the batteries before you

collection point. Dispose of the batteries at

have trouble removing the batteries, you can
also take the appliance to a Philips service
centre.The staff of this centre will remove the
batteries for you and will dispose of them in
an environmentally safe way.
8.0.1Disposalofthebatteries
Remove the battery from the Pure Water
Dispenser before you discard the Pure Water
Dispenser after end of life
1  OpenthedoorofthePureWaterDispenser.
2  Useacrossheadscrewdrivertoremovethe
threescrewsonthecomponentcover.
•
•
4  Cleanthequartztubewithcleanmoistcloth
anddryitcompletely.
5  InserttherubberO-ringtothedepthof2-3
mmfromtheopenend.
6  Insertthetubewiththerubbero-ringinthe
chamber.
7  PuttheUVLampassemblybackintoplace
(withthelampsupport&wires).
8  FixtheUVLampretainingcap.
9  Fixthewireconnectorsback.
10 ClosetheUVaccesscover.
7.0.6Supplyofconsumabletreatment
components


Domestic Appliances and Personal Care Products
(see chapter Guarantee & Service).

17
9 Guarantee and
service
If you need information or if you have a problem,
please visit the Philips Web site at www.Philips.
com or contact the Philips Customer Care Centre


Customer Care Centre in your country, turn to
your local Philips dealer or contact the Service
Department of Philips Domestic appliances and
Personal Care BV.
9.0.1GuaranteeRestrictions/Exceptions
1 TheguaranteedoesnotcoverthePure
WaterDispenserpartsthataresubjectto
wearandtear,thatcanbeconsideredas
consumablepartsbytheirnatureorthatare
madeofglass.
2 Filter(activatedcarbonandsedimentlter)
beingaconsumableisnotcoveredunder
guarantee.
3 Thisguaranteedoesnotextendto
accessories(piping,clamps,adaptor,seal
etc)ifanysuppliedwiththisPureWater
Dispenser.
4 PhilipsDAPoritsauthorizedservice
personnelwillbeentitledtoretainall
defectivepartreplacedunderguarantee
5 IfthePureWaterDispenserisinstalled
outsidecitylimitsoftheservicecenter,then
toandfroconveyanceandotherincidental
expensesincurredbyservicepersonnel/
engineeroninstallationorservicewillbe
bornebythecustomer.
6 AllexpensesincurredinRe-installation,
collectionanddeliveryasregardsservice
requirementsofthePureWaterDispenser
fromPhilipsAuthorizedServiceCenter
/Dealerwillbebornebythecustomer.
7 InspectionandTestReportsofthecompany
willbenalandbindingunderguaranteeif
repairs/modicationsarecarriedoutoras
3  Removethefourscrewsonthebattery
bracket.
4  Pulldownthebracketholdingthebattery.
Remove the battery after disconnecting the
battery connections.
ENGLISH

18
regardscertifyingworkingofthePureWater
Dispenser.
8 Guaranteewillcease/willnotbevalid
anymoreifthePureWaterDispenserisused
forcommercialpurposes.
10Troubleshooting
Problem Cause Solution
FilterLEDblinking Filternotworkingoptimum.End
stage.
Buynewlterforlaterreplacement
Filter LED constant Filterneedreplacement. Forreplacementoflter,seechapter
8.
BatteryLEDblinkingred Batteryatitscriticalstage,needs
charging.
SwitchontheACsupply.
BatteryLEDblinkinggreen Batteryisbeingcharged.
WaterLEDglowsconstantly Waterisnotavailable. Checkwateravailabilitywith
appropriatepressure(0.5-2bar).
Waterdrippingfromtheappliance Pipemaynotbeconnectedproperly. Checkalltheconnections.Contact
yourdealeroraPhilipsservice
centre.
UV LED ON ANerrorintheUVchamber. CheckifUVcoverisclosed.Clean
quartztube(seesection7.0.5).If
problempersists,contactyourdealer
oraPhilipsservicecentre.
Notdispensingwatereveniferror
indications are off
Nopower(IncaseofModelswithout
battery).
Checkifmainspowersupplyis
availableandthepowercordis
correctlyconnected.
Filterisnotmountedproperly. Mountlterproperly.
NonPhilipsltermounted. AlwaysbuyoriginalPhilipslter.
Fuseblownupduevoltageuctations. ContactyourdealeroraPhilips
servicecentre.
Filterexpirybeforeitsstipulated
3000litres.
ContactyourdealeroraPhilips
servicecentre.
AlltheLEDindicatorsdonotash
on Power ON (as per regular
behaviour)
LEDdamaged. ContactyourdealeroraPhilips
servicecentre.

19
Symbol LEDDescription Colour On/Constant Flashing Off
yPower Green PowerOn/Standby
zBattery Green FullyCharged
(WP3983)
Charging
zBattery Red Working,onbat-
tery(WP3893)
Critical,charging
required
UV UV(UltraViolet) Red UV-error
bWater Red Nowateravail-
able(orwater
availableatpres-
surebelowmini-
mumrequired)
Waitingforwater
cFilter Red Replacelter Endstageoflter
life
dDispense Green Waterbeing
dispensed
ePuricationstage
indicator
Red/Yellow/Green Performingpuri-
cation staged
yAuto Blue Inautomode Manual mode
11Technicaldata
1 UVLamp:TUVPLS-9Watt
2 PowerRating:30Wattmax
3 OperatingVoltage:230V±10,50Hz
4 InputWaterPressure


5 InputWaterTemperature


6 Outputwaterowrate:1.2lit/min(max)
7 Fuse:Lamp,slowblow
DNote:
ncasethewaterpressureisabove2Bar,
pressureregulator/reducershouldbeused.
Incasethewaterpressureisbelow0.5bar,use
ofadomesticpumpisrecommended.
Dimensions:


Weight: Product
Model WP3892: - 3.8 Kg

•
•
•
•
This Philips Pure Water Dispenser conforms
to NSF/ANSI 42 for removal of chlorine and
particulates (removes all classes of particulates


and volatile organic chemicals (VOC’s).This Pure

for the removal of cysts.
This Philips Pure Water Dispenser conforms

microbiologically contaminated water that meets
all other public health standards.The system is
not intended for the treatment of water that has
an obvious contamination or intentional source,
such as raw sewage, nor is the system intended
to convert waste water to microbiologically safe
drinking water.

20
12 Frequently asked
questions
Note:
CanIusethePhilipsPureWaterDispenseron
well/borewater?
Yes.The Pure Water Dispenser was designed for
use on potable (drinkable) water sources such as
municipal water or potable well/bore water. It is
not intended for use on lake, river, sewage water
or other untreated water.We recommend that
you have your water tested regularly, if you use
well/bore water.
Cantreatedwaterbestored?
Yes.To prevent treated water from becoming
contaminated, store in a clean container with a

container, treated water may be stored for up to
48 hours.
Canultravioletlightmakethewaterradioactive?
No.While the water in the Pure Water Dispenser
is exposed to ultraviolet light, ultraviolet light is
not radioactive.Therefore, it is impossible for the
water to become radioactive.
DoesthePhilipsPureWaterDispenserchange
thetasteofwater?
The taste of water depends on what’s in the
water.The Pure Water Dispenser removes many
substances such as particulates, chlorine, thus
improving the taste, odour, and clarity of water.
WhatissospecialabouttheUVlamp?
Ultraviolet light is an effective way to destroy
micro-organisms without the use of chemicals.The

that is destructive to micro-organisms.The light
has to be the right intensity and the water must

time to properly dose the water.